ER3C

DATA SHEET ER3A~ER3J SURFACE MOUNT RECTIFIER VOLTAGE FEATURES • For surface mounted applications .128(3.25) .108(2.75) .245(6.22) .220(5.59) 50 to 600 Volts CURRENT 3.0 Amperes SMC/DO-214AB Unit: inch (mm) • High temperature metallurgically bonded-no compression contacts as found in other diode-constructed rectifiers • Glass passivated junction • Built-in strain relief • Easy pick and place • Plastic package has Underwriters Laboratory Flammability Classification 94V-O • Both normal and Pb free product are available : .280(7.11) .260(6.60) .012(.305) .006(.152) Normal : 80~95% Sn, 5~20% Pb Pb free: 98.5% Sn above .103(2.62) .079(2.00) .050(1.27) .030(0.76) .320(8.13) .305(7.75) MECHANICALDATA Case: JEDEC DO-214AB molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard packaging: 16mm tape (EIA-481) Weight: 0.007 ounce, 0.21 gram .008(.203) .002(.051) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. P A R A M E TE R M a xi um R e curre nt P e a k R e ve rse V o l a g e m t M a xi um R M S V o l a g e m t M a xi um D C B l cki g V o l a g e m o n t M a xi um A ve ra g e F o rw a rd C urre nt . 7 5 "(9 . m m ) m 3 5 l a d l ng t a t T L = 7 5 O C e e h P e a k F o rw a rd S urg e C urre nt : 8 . m s si g l ha l si e -w a ve 3 ne fn sup e ri p o se d o n ra t d l a d (JE D E C m e t o d ) m eo h M a xi um F o rw a rd V o l a g e a t 3 . A m t 0 M a xi um D C R e ve rse C urre nt T A = 2 5 C m a t R a t d D C B l cki g V o l a g e T A = 1 0 0 O C e o n t M a xi um R e ve rse R e co ve ry Ti e (N o t 1 ) m m e Typ i a l Junct o n ca p a ci a nce (N o t 2 ) c i t e M a xi um t e rm a l R e si t nce (N o t 3 ) m h sa e O p e ra t ng a nd S t ra g e Te m p e ra t re R a ng e i o u O S YM B O L V RRM V RM S VDC IV A I SM F VF I R TR R CJ R θ JL T J, S TG T E R 3A 50 35 50 E R 3B 100 70 100 E R 3C 150 105 150 E R 3D 200 140 200 3. 0 100 E R 3E 300 210 300 E R 3G 400 280 400 E R 3J 600 420 600 UNI S T V V V A A 0. 5 9 5. 0 200 35 45 16 -5 0 T O + 1 5 0 1. 5 2 1. 7 V uA ns pF O C /W O C NOTES:1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A 2. Measured at 1 MHz and applied Vr = 4.0 volts. 3. 8.0 mm2 ( .013mm thick ) land areas. STAD-MAR.10.2004 PAGE . 1 RATING AND CHARACTERISTIC CURVES 100 AVERAGE FORWARD RECIFIED CURRENT AMPERES 90 80 TJ = 25 C f = 1.0MHZ Vsig = 50mVp-p O 3 CAPACITANCE, pF 70 60 50 40 30 20 10 0 0.1 1 10 100 1000 2 1 SINGLE PHASE, HALF-WAVE, 60Hz RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.3 x 0.3" (8.0 x 8.0 mm)COPPER PAD AREAS 0 20 40 60 80 100 120 O 0 140 160 180 REVERSE VOLTAGE, VOLTS LEAD TEMPERATURE, C FIG.1 TYPICAL JUNCTION CAPACITANCE FIG.2 MAXIMUM AVERAGE FORWARD CURRENT RATING 100 TJ=100 C O INSTANTANEOUS FORWARD CURRENT AMPERES 100 INVSTANTANEOUS REVERSE CURRENT, MICROAMPERES 50-200V 10 10 TJ=75 C O 300-400V 1.0 600V 1.0 TJ=25 C O 0.1 TJ=25 C PULSE WIDTH= 300mS 2% DUTY CYCLE 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 O 0.1 0.01 2 40 60 80 60 80 100 120 140 PERCENT OF RATED PEAK INVERSE VOLTGE, VOLTS INSTANTANEOUS FORWARD VOLTAGE VOLTS FIG.3 TYPICAL REVERSE CHARACTERISTICS FIG.4 TYPICAL FORWARD CHARACTERISTICS 110 FORWARD SURGE CURRENT, AMPERES 100 90 80 70 60 50 8.3ms SINGLE HALF SINE-WAVE JEDC METHOD 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPEITIVE SURGE CURRENT STAD-MAR.10.2004 PAGE . 2