GBJ6G

DATA SHEET GBJ6A~GBJ6K GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER GBJ VOLTAGE 50 to 800 Volts CURRENT 6.0 Ampere Unit: inch (mm) Recongnized File #E228882 FEATURES • Plastic material has Underwriters Laboratory Flammability Classification 94V-O • Ideal for printed circuit board • Reliable low cost construction utilizing molded plastic technique .146(3.7) .129(3.3) C .118(3.0) .996(25.3) .972(24.7) .142(3.6) .122(3.1) .189(4.8) .173(4.4) .150(3.8) .133(3.4) • High temperature soldering guaranteed: 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension • Both normal and Pb free product are available: Normal : 80~95% Sn, 5~20% Pb Pb free: 98.5% Sn above .603(15.3) .578(14.7) .709(18.0) .669(17.0) .087(2.2) .070(1.8) .044(1.1) .035(0.9) .304(7.7) .288(7.3) .115(2.9) .098(2.5) MECHANICALDATA Case: Reliable low cost construction utilizing molded plastic technique Terminals: Leads solderable per MIL-STD-202, Method 208 Mounting position: Any Mounting torque: 5 in. lb. Max. Weight: 0.15 ounce, 4.0 grams .304(7.7) .288(7.3) .304(7.7) .288(7.3) .032(0.8) .024(0.6) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%. PA RA M E TE R M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e M a x i m u m R M S B r i d g e In p u t V o l t a g e M a xi m um D C B l o c k i ng V o l t a g e M a xi m um A ve r a g e F o r w a r d R e c t i f i e d O ut p ut C ur r e nt a t T C = 1 0 0 OC I2 t R a t i n g f o r f u s i n g ( t < 8 . 3 m s ) P e a k F o r w a r d S ur g e C ur r e nt s i ng l e s i ne - w a ve s up e r i m p o s e d o n r a t e d l o a d ( J E D E C m e t ho d ) M a x i m u m In s t a n t a n e o u s F o r w a r d V o l t a g e D r o p p e r e l e m e n t a t 3 .0 A M a xi m um R e ve r s e L e a k a g e C ur r e nt a t R a t e d @ T A = 2 5 OC D c B l o c k i ng V o l t a g e @ T A = 1 0 0 OC Ty p i c a l T h e r m a l R e s i s t a n c e p e r l e g ( N o t e 2 ) (No te 3 ) O p e r a t i n g J u n c t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e S YM B O L GB J 6 A GB J 6 B GB J 6 D 50 35 50 100 70 100 200 140 200 6 .0 127 175 1 .0 5 .0 500 8 .6 3 .1 -5 5 to + 1 5 0 O GB J 6 G GB J 6 J GB J 6 K 400 280 400 600 420 600 800 560 800 V RRM V RM S V DC I AV I2 t IF S M VF IR R θJ A R θJ C .382(9.7) .366(9.3) U N IT S V V V A A 2s e c Apk Vpk uA C /W T J ,T S TG O C NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate. STAD-FEB.20.2004 PAGE . 1 RATING AND CHARACTERISTIC CURVES FORWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) AVERAGE FORWARD CURRENT AMPERES 6.0 HEAT-SINK MOUNTING, T C (4 x 4 x 0.15cm)THK COPPER PLATE 175 140 4.0 105 2.0 MOUNTED ON PC BOARD, TA 0.5 (12.7mm)LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD 70 35 0 0 50 100 O 150 0 1 2 6 10 20 40 60 100 CASE TEMPERATURE, C NO. OF CYCLES AT 60Hz Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT Fig.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 4 100 40 20 10 4.0 2.0 1.0 10 3 REVERSE CURRENT,uA 10 2 T J =150 C O 10 1 10 0 T J =25 C O 10 -1 0.4 0.2 0.1 0.7 0.8 0.9 1.0 1.1 TJ=25 C Pulse Width = 300us 1% DULY Cycle O 10 -2 0 10 20 30 40 50 60 70 80 90 100 110 1.2 1.3 1.4 PERCENT OF PEAK REVERE VOLTAGE,% INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig.3 - TYPICAL REVERSE CHARACTERISTICS Fig.4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER ELEMENT STAD-FEB.20.2004 PAGE . 2