SMF70A

SMF5.0A~SMF170A SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR VOLTAGE FEATURES • For surface mounted applications in order to optimize board space. • Low profile paceage • Built-in strain relief • Low inductance • High temperature soldering : 260 OC/10 seconds at terminals • In compliance with EU RoHS 2002/95/EC directives 5.0 to 170 Volts CURRENT 200 Watts MECHANICAL DATA • Case: JEDEC DO-219AB,Molded plastic over passivated junction. • Terminals: Solderable per MIL-STD-750, Method 2026 • Polarity: Color band denotes positive end (cathode) • Weight: 0.0006 ounce, 0.0172 gram • Standrad Packaging : 8mm tape (EIA-481) 1 2 Cathode Anode MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25OC ambient temperature unless otherwise specified. Rating Peak Pulse Power Dissipation on T A = 25 OC (Notes 1,2,5, Fig.1) Peak Forward Surge Current per (Note 3) Peak Pulse Current on 10/1000s waveform(Note 1)Fig.2 Steady State Power Dissipation (NOTE 4) Operating Junction and Storage Temperature Range Thermal resistance Symbol PPPM IFSM IPPM PM(AV) TJ,TSTG RθJA Value 200 20 see Table 1 1.0 -55 to +150 180 Units Watts Amps Amps Watts O C C O NOTES : 1.Non-repetitive current pulse, per Fig.3 and derated above T A =25 OC per Fig.2 . 2.Mounted on 5.0mm 2 c opper pads to each terminal. 3.8.3ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minutes maximum. 4.lead temperature at 75 OC =T L . 5.Peak pulse power waveform is 10/1000 μ s. May 04.2010-REV.00 PAGE . 1 SMF5.0A~SMF170A V BR @ IT V R WM Part Number V 200W Transient Voltage Suppressor SMF5.0A SMF6.0A SMF6.5A SMF7.0A SMF7.5A SMF8.0A SMF8.5A SMF9.0A SMF10A SMF11A SMF12A SMF13A SMF14A SMF15A SMF16A SMF17A SMF18A SMF20A SMF22A SMF24A SMF26A SMF28A SMF30A SMF33A SMF36A SMF40A SMF43A SMF45A SMF48A SMF51A SMF54A SMF58A SMF60A SMF64A SMF70A SMF75A SMF78A SMF85A SMF90A SMF100A SMF110A SMF120A SMF130A SMF140A SMF160A SMF170A 5 6 6.5 7 7.5 8 8.5 9 10 11 12 13 14 15 16 17 18 20 22 24 26 28 30 33 36 40 43 45 48 51 54 58 60 64 70 75 78 85 90 100 110 120 130 150 160 170 6.4 6.7 7.2 7.8 8.3 8.9 9.4 10 11.1 12.2 13.3 14.4 15.6 16.7 17.8 18.9 20 22.2 24.4 26.7 28.9 31.1 33.3 36.7 40 44.4 47.8 50 53.3 56.7 60 64.4 66.7 71.1 77.8 83.3 86.7 94.4 100 111 122 133 144 167 178 189 7 7.4 8 8.6 9.2 9.8 10.4 11.1 12.3 13.5 14.7 15.9 17.2 18.5 19.7 20.9 22.1 24.5 26.9 29.5 31.9 34.4 36.8 40.6 44.2 49.1 52.8 55.3 58.9 62.7 66.3 71.2 73.7 78.6 86 92.1 95.8 104 111 123 135 147 159 185 197 209 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 400 400 250 100 50 25 10 5 2.5 2.5 2.5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 9.2 10.3 11.2 12 12.9 13.6 14.4 15.4 17 18.2 19.9 21.5 23.2 24.4 26 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103 113 121 126 137 146 162 177 193 209 243 259 275 21.7 19.4 17.9 16.7 15.5 14.7 13.9 13 11.8 11 10.1 9.3 8.6 8.2 7.7 7.2 6.8 6.2 5.6 5.1 4.8 4.4 4.1 3.8 3.4 3.1 2.9 2.8 2.6 2.4 2.3 2.1 1.8 1.7 1.5 1.4 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 0.7 0.6 HE HG HK HM HP HR HT HV HX HZ IE IG IK IM IP IR IT IV IX IZ JE JG JK JM JP JR JT JV JX JZ RE RG RK RM RP RR RT RV RX RZ SE SG SK SM SP SR Min . V Max. V IT mA μA V A IR @ VRWM VC @ IPP Marking Code May 04.2010-REV.00 PAGE . 2 SMF5.0A~SMF170A P PPM ,PEAK PULSE FORWARD ,KW 100 Non-Repetitve Pulse Waveform Shown in Figure.3 T A = 25 OC 100 PEAK PULSE FORWARD (P PP) OR CURRENT (I PP) DERATING IN PERCENTAGE % 75 10 50 1.0 25 0.1 0.1 1.0 10 100 1000 10000 0 0 25 50 75 100 125 150 175 200 td ,PULSE WIDTH, micro sec T A ,AMBIENT TEMPERATURE, C O Fig.1 PEAK PULSE POWER RATING CURVE Fig.2 DERATING CURVE I PPM ,PEAK PULSE CURRENT,% 150 tf = 10usec T A = 25 C Pulse Width (td) is Defined as the Point where the Peak Current Decayst to 50% of Ipp O 10,000 T J = 25 C f= 1.0MHZ Vsig = 50mVp -p O 100 Peak Value Ippm Ha lf Va lue -Ip p 2 10/1000 msec Waveform as Defined by R.E.A. CJ , CAPACITANCE , pF 1,000 Mea sured a t Ze ro Bia s 50 e -kt td 0 0 1.0 2.0 3.0 4.0 100 Me a sure d a t Sta nd -Off Volta ge (VRWM) T,TIME,ms Fig.3 PULSE WAVEFORM 10 1.0 2.0 5.0 10 20 50 100 200 I FSM , PEAK FORWARD SURGE CURRENT, AMPERES 50 40 T J=T J MAX 8.3ms Single Half Sine-Wave JEDEC Method V(RWM) , REVERSE STAND-OFF VOLTAGE , VOLTS 30 Fig.4 TYPICAL JUNCTION CAPACITANCE 20 10 0 1 2 4 10 20 40 100 NUMBER OF CYCLES AT 60Hz Fig.5 MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT May 04.2010-REV.00 PAGE . 3 SMF5.0A~SMF170A MOUNTING PAD LAYOUT ORDER INFORMATION • Packing information T/R - 10K per 13" plastic Reel T/R - 3K per 7" plastic Reel LEGAL STATEMENT Copyright PanJit International, Inc 2010 The information presented in this document is believed to be accurate and reliable. The specifications and information herein are subject to change without notice. Pan Jit makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose. Pan Jit products are not authorized for use in life support devices or systems. Pan Jit does not convey any license under its patent rights or rights of others. May 04.2010-REV.00 PAGE . 4