1F1

FAST RECOVERY RECTIFIER 1F1 THRU 1F7 FEATURES • • • • • VOLTAGE RANGE CURRENT 50 to 1000 Volts 1.0 Ampere R-1 .787 MIN. (20.0) Low coat construction Fast switching for high efficiency. Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 260℃/10 secods/.375”(9.5mm)lead length at 5 lbs(2.3kg) tension .138(3.5) .114(2.9) .102(2.6) DIA. .087(2.2) MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-O rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.007ounce, 0.20 grams .787 MIN. (20.0) .025(0.6) DIA. .021(0.5) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25OC ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current 0.375”(9.5mm) lead length at T A= 25℃ Peak Forward Surge Current 8.3mS single half sine wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current at Rated DC Blocking Voltage T A = 25℃ TA = 100℃ VRRM VRMS VDC I(AV) IFSM VF IR Trr CJ RθJA 1F1 50 35 50 1F2 100 70 100 1F3 200 140 200 1F4 400 280 400 1.0 25 1.3 5.0 50 250 15 50 1F5 600 420 600 1F6 800 560 800 1F7 1000 700 1000 UNITS Volts Volts Volts Amps Amps Volts µAmps Maximum Reverse Recovery Tine (Note 3) T J=25℃ Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Operating and Storage Temperature Range 150 500 ns pF ℃/W ℃ TJTSTG -55 to +150 Notes: 1.Measured at 1.0MHz and Applied Reverse Voltage of 4.0Volits. 2.Thermal Resistance from junction to Ambient at .375”(9.5mm)lead length, P.C.board mounted. 3.Reverse Recovery Test Conditions:If=0.5A,Ir=1.0A,Irr=0.25A Web Site: WWW.PS-PFS.COM FAST RECOVERY RECTIFIER 1F1 THRU 1F7 VOLTAGE RANGE CURRENT 50 to 1000 Volts 1.0 Ampere RATING AND CHRACTERISTIC CURVES 1F1 Thur 1F7 FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 1.2 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 AVERAGE FORW ARD CURRENT, (A) PEAK FORWARD SURGE 1.0 25 0.8 CURRENT, (A) 20 8.3ms Single Half Sine-Wave (JEDEC Method) =T T j jmax 0.6 0.4 Single Phase Half Wave 60Hz Resistive or 10 0.2 0 0 Inductive Load 25 50 75 100 125 150 175 0 1 2 5 8 10 20 50 100 AMBIENT TEMPERATURE, (° C) NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 20 FIG.4-TYPICAL REVERSE CHARACTERISTICS 10 10 INSTANTANEOUS FORWARD CURRENT, INSTANTANEOUS REVERSE CURRENT, (mA) 1 1.0 (A) Tj =100° C 0.1 Tj =25° C Pulse Width=300us 1% Duty Cycle 0.1 0.01 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Tj =25° C 0.01 0 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD VOLTAGE,(V) PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE 100 CAPACITANCE,(pF) 10 TJ=25° C F=1MHz 10 0.1 1.0 4.0 10.0 100 REVERSE VOLTAGE,(VOLTS) Web Site: WWW.PS-PFS.COM