CBTS3306D

INTEGRATED CIRCUITS CBTS3306 Dual bus switch with Schottky diode clamping Product data File under Integrated Circuits — ICL03 2001 Nov 08 Philips Semiconductors Philips Semiconductors Product data Dual bus switch with Schottky diode clamping CBTS3306 FEATURES • 5 Ω switch connection between two ports • TTL-compatible input levels • Package options include plastic small outline (SO) and thin shrink small outline (TSSOP) PIN CONFIGURATION 1OE 1A 1B GND 1 2 3 4 8 7 6 5 VCC 2OE 2B 2A • Latch-up protection exceeds 100 mA per JESD78 • ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101 SA00535 PIN DESCRIPTION DESCRIPTION The CBTS3306 Dual FET Bus Switch features independent line switches with Schottky diodes on the I/OS to clamp undershoot. Each switch is disabled with the associated Output Enable (OE) input is high. The CBTS3306 is characterized for operation from –40 to +85 °C. PIN NUMBER 1, 7 2, 5 3, 6 4 8 SYMBOL 1OE, 2OE 1A, 2A 1B, 2B GND VCC NAME AND FUNCTION Output enable A port inputs B port outputs Ground (0 V) Positive supply voltage QUICK REFERENCE DATA SYMBOL tPLH tPHL CIO(OFF) ICC Propagation delay A to B or B to A Port off capacitance Quiescent supply current PARAMETER CONDITIONS Tamb = 25 °C; GND = 0 V CL = 50 pF; VCC = +5.0 V ±0.5 V VO = 3 V or 0; OE = VCC VCC = 5.5 V; IO = 0, VI = VCC or GND TYPICAL 0.25 (MAX) 7.60 3 UNIT ns pF µA ORDERING INFORMATION PACKAGES 8-pin plastic SO 8-pin plastic TSSOP TEMPERATURE RANGE –40 to 85 °C –40 to 85 °C ORDER CODE CBTS3306D CBTS3306PW DWG NUMBER SOT96-1 SOT530-1 Standard packing quantities and other packaging data is available at www.philipslogic.com/packaging. LOGIC DIAGRAM (positive logic) 1A 2 3 1B FUNCTION TABLE INPUT OE L H FUNCTION A port = B port Disconnect 1OE 1 2A 5 6 2B 2OE 1 SA00618 2001 Nov 08 2 853-2306 27313 Philips Semiconductors Product data Dual bus switch with Schottky diode clamping CBTS3306 ABSOLUTE MAXIMUM RATINGS1 Tamb = –40 to +85 °C, unless otherwise specified. SYMBOL VCC VI IOUT IIK Tstg PARAMETER DC supply voltage DC input voltage2 DC output current Diode current Storage temperature range VI/O < 0 CONDITIONS RATING –0.5 to +7.0 –0.5 to +7.0 128 –50 –65 to +150 UNIT V V mA mA °C NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 3. The package thermal impedance is calculated in accordance with JESD 51. RECOMMENDED OPERATING CONDITIONS1 SYMBOL VCC VIH VIL Tamb DC supply voltage High-level input voltage Low-level Input voltage Operating free-air temperature range PARAMETER LIMITS MIN 4.5 2.0 — –40 MAX 5.5 — 0.8 +85 UNIT V V V °C NOTE: 1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. DC ELECTRICAL CHARACTERISTICS Tamb = –40 to +85 °C, unless otherwise specified. LIMITS SYMBOL PARAMETER A or B input Control inputs TEST CONDITIONS VCC = 4.5 V; II = –18 mA VCC = 4.5 V; II = –18 mA VCC = 5.5 V; VI = GND or 5.5 V VCC = 5.5 V; IO = 0, VI = VCC or GND VO = VCC = 5.0 V; II = –100 mA pin2 VCC = 5.5 V, one input at 3.4 V, other inputs at VCC or GND VI= 3 V or 0 VO = 3 V or 0; OE = VCC VCC = 4.5 V; VI = 0 V; II = 64 mA ron 3 Tamb = –40 to +85 °C MIN TYP1 — — — — 3.6 — 3.25 7.60 3.4 3.4 6.8 MAX –0.7 –1.2 ±1 3 3.9 2.5 — — 5 5 7.5 — — — — 3.4 — — — — — — UNIT VIK II ICC VP ∆ICC CI CIO(OFF) Input clamp voltage Input clamp voltage Input leakage current Quiescent supply current Output high pass voltage V µA µA V mA pF pF Ω Ω Ω Additional supply current per input Control pin capacitance Port off capacitance On-resistance VCC = 4.5 V; VI = 0 V; II = 30 mA VCC = 4.5 V; VI = 2.4 V; II = 15 mA NOTES: 1. All typical values are at VCC = 5 V, Tamb = 25 °C. 2. This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND 3. Measured by the voltage drop between the A and the B terminals at the indicated current through the switch. On-state resistance is determined by the lowest voltage of the two (A or B) terminals. 2001 Nov 08 3 Philips Semiconductors Product data Dual bus switch with Schottky diode clamping CBTS3306 AC CHARACTERISTICS Tamb = –40 to +85 °C; CL = 50 pF LIMITS SYMBOL tpd ten tdis PARAMETER Propagation delay1 Output enable time to High and Low level Output disable time from High and Low level FROM (INPUT) A or B OE OE TO (OUTPUT) B or A A or B A or B VCC = +5.0 V ±0.5 V MIN — 1.8 1 MAX 0.25 5 5 ns ns ns UNIT NOTE: 1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). AC WAVEFORMS VM = 1.5 V, VIN = GND to 3.0 V 3V 1.5 V INPUT 0V tPLH tPHL VOH 1.5 V OUTPUT VOL 1.5 V 1.5 V TEST CIRCUIT AND WAVEFORMS 7V From Output Under Test CL = 50 pF 500 Ω S1 Open GND 500 Ω Load Circuit TEST tpd tPLZ/tPZL tPHZ/tPZH S1 open 7V open SA00028 Waveform 1. Input to Output Propagation Delays DEFINITIONS Load capacitance includes jig and probe capacitance; CL = see AC CHARACTERISTICS for value. 3V Output Control (Low-level enabling ) tPZL Output Waveform 1 S1 at 7 V (see Note) tPZH Output Waveform 2 S1 at Open (see Note) 1.5 V 1.5 V 0V 3.5 V 1.5 V tPHZ VOH – 0.3 V 1.5 V 0V Note: Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. SA00012 tPLZ NOTES: 1. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. 2. The outputs are measured one at a time with one transition per measurement. VOL + 0.3 V VOL VOH SA00029 Waveform 2. 3-State Output Enable and Disable Times NOTES: 1. tPLZ and tPHZ are the same as tdis. 2. tPZL and tPZH are the same as ten. 3. tPLH and tPHL are the same as tpd. 2001 Nov 08 4 Philips Semiconductors Product data Dual bus switch with Schottky diode clamping CBTS3306 TSSOP8: plastic thin shrink small outline; 8 leads; body width 4.4 mm SOT530-1 2001 Nov 08 5 Philips Semiconductors Product data Dual bus switch with Schottky diode clamping CBTS3306 SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 2001 Nov 08 6 Philips Semiconductors Product data Dual bus switch with Schottky diode clamping CBTS3306 NOTES 2001 Nov 08 7 Philips Semiconductors Product data Dual bus switch with Schottky diode clamping CBTS3306 Data sheet status Data sheet status [1] Objective data Preliminary data Product status [2] Development Qualification Definitions This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. Product data Production [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 © Koninklijke Philips Electronics N.V. 2001 All rights reserved. Printed in U.S.A. Date of release: 11-01 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. Document order number: 9397 750 09117 Philips Semiconductors 2001 Nov 08 8