PCA9516PW

INTEGRATED CIRCUITS PCA9516 5-channel I2C hub Product data Supersedes data of 2002 Mar 01 2002 May 13 Philips Semiconductors Philips Semiconductors Product data 5-channel I2C hub PCA9516 PIN CONFIGURATION SCL0 1 SDA0 SCL1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VCC EN4 SDA4 SCL4 EN3 SDA3 SCL3 EN2 DESCRIPTION The PCA9516 is a BiCMOS integrated circuit intended for application in I2C and SMBus systems. While retaining all the operating modes and features of the system, it permits extension of the I2C bus by buffering both the data (SDA) and the clock (SCL) lines, thus enabling five buses of 400 pF. The I2C bus capacitance limit of 400 pF restricts the number of devices and bus length. Using the PCA9516 enables the system designer to divide the bus into five segments off of a hub where any segment to segment transition sees only one repeater delay. It can also be used to run different buses at 5 V and 3.3 V or 400 kHz and 100 kHz buses where the 100 kHz bus is isolated when 400 kHz operation of the other bus is required. I2C SDA1 EN1 SCL2 SDA2 GND SU01395 Figure 1. Pin configuration PIN DESCRIPTION PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SYMBOL SCL0 SDA0 SCL1 SDA1 EN1 SCL2 SDA2 GND EN2 SCL3 SDA3 EN3 SCL4 SDA4 EN4 VCC FUNCTION Serial clock bus 0 Serial data bus 0 Serial clock bus 1 Serial data bus 1 Active High Bus 1 enable Input Serial clock bus 2 Serial data bus 2 Supply ground Active High Bus 2 enable Input Serial clock bus 3 Serial data bus 3 Active High Bus 3 enable Input Serial clock bus 4 Serial data bus 4 Active High Bus 4 enable Input Supply power FEATURES • 5 channel, bi-directional buffer • I2C-bus and SMBus compatible • Active high individual repeater enable input • Open-drain input/outputs • Lock-up free operation • Supports arbitration and clock stretching across the repeater • Accommodates standard mode and fast mode I2C devices and multiple masters • Powered-off high impedance I2C pins • Operating supply voltage range of 3.0 V to 3.6 V • 5 V tolerant I2C and enable pins • 0 to 400 kHz clock frequency1 • ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101. • Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA. • Package offerings: SO and TSSOP ORDERING INFORMATION DESCRIPTION 16-pin plastic SO (narrow) TEMPERATURE RANGE –40 to +85 °C ORDER CODE PCA9516D DRAWING NUMBER SOT109-1 SOT403-1 16-pin plastic TSSOP –40 to +85 °C PCA9516PW Standard packing quantities and other packaging data is available at www.philipslogic.com/packaging. 1. The maximum system operating frequency may be less than 400 KHz because of the delays added by the repeater. 2002 May 13 2 853–2234 28185 Philips Semiconductors Product data 5-channel I2C hub PCA9516 VCC PCA9516 SCL0 Buffer Buffer Hub Logic SCL4 SCL1 Buffer Buffer SCL2 Buffer SCL3 SDA0 Buffer Buffer Hub Logic SDA4 SDA1 Buffer Buffer SDA2 Buffer SDA3 EN1 EN4 EN2 EN3 SU01396 GND Figure 2. Block Diagram: PCA9516 A more detailed view of Figure 2 buffer is shown in Figure 3. To output Data z In Inc Enable SW00712 Figure 3. The output pull-down of each internal buffer is set for approximately 0.5 V, while the input threshold of each internal buffer is set about 0.07 V lower, when the output is internally driven low. This prevents a lock-up condition from occurring. 2002 May 13 3 Philips Semiconductors Product data 5-channel I2C hub PCA9516 FUNCTIONAL DESCRIPTION The PCA9516 BiCMOS integrated circuit is a five way hub repeater, which enables I2C and similar bus systems to be expanded with only one repeater delay and no functional degradation of system performance. The PCA9516 BiCMOS integrated circuit contains five bi-directional, open drain buffers specifically designed to support the standard low-level-contention arbitration of the I2C-bus. Except during arbitration or clock stretching, the PCA9516 acts like five pairs of non-inverting, open drain buffers, one for SDA and one for SCL. the other side to also go low. The side driven low by the PCA9516 will typically be at VOL = 0.5 V. In order to illustrate what would be seen in a typical application, refer to Figures 5 and 6. If the bus master in Figure 4 were to write to the slave through the PCA9516, we would see the waveform shown in Figure 5 on Bus 0. This looks like a normal I2C transmission until the falling edge of the 8th clock pulse. At that point, the master releases the data line (SDA) while the slave pulls it low through the PCA9516. Because the VOL of the PCA9516 is typically around 0.5 V, a step in the SDA will be seen. After the master has transmitted the 9th clock pulse, the slave releases the data line. 3.3 V Enable The enable pins EN1 through EN4 are active high and have internal pull-up resistors. Each enable pin ENn controls its associated SDAn and SCLn ports. When low the ENn pin blocks the inputs from SDAn and SCLn as well as disabling the output drivers on the SDAn and SCLn pins. The enable pins should only change state when both the global bus and the local port are in an idle state to prevent system failures. The active high enable pins allow the use of open drain drivers which can be wire-ORed to create a distributed enable where either centralized control signal (master) or spoke signal (submaster) can enable the channel when it is idle. 5V SDA SCL BUS MASTER SDA0 SCL0 SDA1 SCL1 3.3 V SDA SLAVE 1 SCL 400 kHz PCA9516 EN1 EN2 EN3 EN4 I2C Systems As with the standard I2C system, pull-up resistors are required to provide the logic HIGH levels on the Buffered bus. (Standard open-collector configuration of the I2C-bus). The size of these pull-up resistors depends on the system, but each side of the repeater must have a pull-up resistor. This part designed to work with standard mode and fast mode I2C devices in addition to SMBus devices. Standard mode I2C devices only specify 3 mA output drive, this limits the termination current to 3 mA in a generic I2C system where standard mode devices and multiple masters are possible. Under certain conditions higher termination currents can be used. Please see Application Note AN255 “I 2C & SMBus Repeaters, Hubs and Expanders” for additional information on sizing resistors and precautions when using more than one PCA9515/PCA9516 in a system or using the PCA9515/16 in conjunction with the P82B96. 400 kHz SDA2 SCL2 5V SDA SLAVE 2 SCL 400 kHz SDA3 SCL3 SDA SLAVE 3 SCL 5V 100 kHz APPLICATION INFORMATION A typical application is shown in Figure 4. In this example, the system master is running on a 3.3 V I2C-bus while the slave is connected to a 5 V bus. All buses run at 100 kHz unless slave 3 and 4 are isolated and then the master bus and slave 1 and 2 can run at 400 kHz. Any segment of the hub can talk to any other segment of the hub. Bus masters and slaves can be located on all five segments with 400 pF load allowed on each segment. The PCA9516 is 5 V tolerant so it does not require any additional circuitry to translate between the different bus voltages. When one side of the PCA9516 is pulled low by a device on the I2C-bus, a CMOS hysteresis type input detects the falling edge and causes an internal driver on the other side to turn on, thus causing SDA4 SCL4 SDA SLAVE 4 SCL 100 kHz SW00923 Figure 4. Typical application 2002 May 13 4 Philips Semiconductors Product data 5-channel I2C hub PCA9516 2 V/DIV 9th CLOCK PULSE VOL OF PCA9516 VOL OF MASTER SW00965 Figure 5. Bus 0 waveform On the Bus 1 side of the PCA9516, the clock and data lines would have a positive offset from ground equal to the VOL of the PCA9516. After the 8th clock pulse, the data line will be pulled to the VOL of the slave device that is very close to ground in our example. It is important to note that any arbitration or clock stretching events on Bus 1 require that the VOL of the devices on Bus 1 be 70 mV below the VOL of the PCA9516 (see VOL – Vilc in the DC Characteristics section) to be recognized by the PCA9516 and then transmitted to Bus 0. 9th CLOCK PULSE 2 V/DIV VOL OF PCA9516 VOL OF SLAVE SW00966 Figure 6. Bus 1 waveform 2002 May 13 5 Philips Semiconductors Product data 5-channel I2C hub PCA9516 ABSOLUTE MAXIMUM RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134). Voltages with respect to pin GND. LIMITS SYMBOL VCC to GND Vbus I Ptot Tstg Tamb Supply voltage range VCC Voltage range I2C-bus, SCL or SDA DC current (any pin) Power dissipation Storage temperature range Operating ambient temperature range PARAMETER MIN. –0.5 –0.5 — — –55 –40 MAX. +7 +7 50 300 +125 +85 UNIT V V mA mW °C °C DC ELECTRICAL CHARACTERISTICS VDD = 3.0 to 3.6 V; GND = 0 V; Tamb = –40 to +85 °C; unless otherwise specified. SYMBOL Supplies VCC ICCH ICCL DC supply voltage Quiescent supply current, both channels HIGH Quiescent supply current, both channels LOW Quiescent supply current in contention VCC = 3.6 V; SDAn = SCLn = VCC VCC = 3.6 V; one SDA and one SCL = GND, other SDA and SCL open VCC = 3.6 V; SDAn = SCLn = GND 3.0 — — 3.3 7 6.8 3.6 10 10 V mA mA PARAMETER TEST CONDITIONS CONDITIONS LIMITS MIN. TYP. MAX. UNIT ICCLc — 7 10 mA Input SCL; input/output SDA VIH VIL VILc VIK II IIL VOL VOL–VILc IOH CI Enable 1–4 VIL VIH IIL ILI CI LOW level input voltage HIGH level input voltage Input current LOW, EN1–EN4 Input leakage current Input capacitance VI = 3.0 V or 0 V VI = 0.2 V, EN1–EN4 –0.5 2.0 — –1 — — — 10 — 6 0.8 5.5 30 1 7 V V µA µA pF High-level input voltage Low-level input voltage (Note 1) Low-level input voltage contention (Note 1) Input clamp voltage Input leakage current Input current LOW, SDA, SCL Low level output Low level input voltage below output low level voltage Output high level leakage current Input capacitance II = –18 mA VI = 3.6 V VI = 0.2 V, SDA, SCL IOL = 0 or 6 mA Guaranteed by design VO = 3.6 V VI = 3 V or 0 V 0.7 VCC –0.5 –0.5 — — — 0.47 — — — — — — — — — .52 — — 6 5.5 0.3 VCC 0.4 –1.2 ±1 5 0.6 70 10 10 V V V V µA µA V mV µA pF NOTE: 1. VIL specification is for enable input and the first low level seen by the SDAx/SCLx lines. VILc is for the second and subsequent low levels seen by the SDAx/SCLx lines. 2002 May 13 6 Philips Semiconductors Product data 5-channel I2C hub PCA9516 AC ELECTRICAL CHARACTERISTICS SYMBOL tPHL tPLH tTHL tTLH tSET tHOLD PARAMETER Propagation delay Propagation delay Transition time Transition time Enable to Start condition Enable after Stop condition TEST CONDITIONS CONDITIONS Waveform 1 Waveform 1 Waveform 1 Waveform 1; Note 1 100 100 LIMITS MIN. 57 33 TYP. 115 55 67 135 MAX. 170 78 UNIT ns ns ns ns ns ns NOTE: 1. The tTLH transition time is guaranteed with loads of 1.35 kΩ pull-up resistance and 7 pF load capacitance, plus an additional 50 pF load capacitance. Different load resistance and capacitance will alter the RC time constant, thereby changing the propagation delay and transition times. AC WAVEFORMS 3.3 V INPUT 1.5 V 1.5 V 0.1 V tPHL 80% OUTPUT 1.5 V 20% tTHL 1.5 V 20% VOL tTLH tPLH 3.3 V 80% TEST CIRCUIT VCC VCC VIN PULSE GENERATOR RT D.U.T. VOUT RL CL Test Circuit for Open Drain Outputs SW00646 DEFINITIONS RL = Load resistor; 1.35 kΩ CL = Load capacitance includes jig and probe capacitance; 7 pF RT = Termination resistance should be equal to ZOUT of pulse generators. SW00792 Waveform 1. 2002 May 13 7 Philips Semiconductors Product data 5-channel I2C hub PCA9516 SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 2002 May 13 8 Philips Semiconductors Product data 5-channel I2C hub PCA9516 TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 2002 May 13 9 Philips Semiconductors Product data 5-channel I2C hub PCA9516 Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the components in the I2C system provided the system conforms to the I2C specifications defined by Philips. This specification can be ordered using the code 9398 393 40011. Data sheet status Data sheet status [1] Objective data Preliminary data Product status [2] Development Qualification Definitions This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. Product data Production [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 © Koninklijke Philips Electronics N.V. 2002 All rights reserved. Printed in U.S.A. Date of release: 05-02 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. Document order number: 9397 750 09815 Philips Semiconductors 2002 May 13 10