2891390

https://www.phoenixcontact.com/us/products/2891390 Industrial Ethernet Switch - FL SWITCH SFNT 5GT - 2891390 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Wide-temperature Ethernet switch, five TP RJ45 ports, automatic detection of data transmission speed of 10/100/1000 Mbps (RJ45), autocrossing function, reads QoS priority messages, accepts security frames. Product Description The FL SWITCH SFN 5GT supports the auto negotiation function at the twisted-pair ports and offers transmission speeds of 10/100/1000 Mbps. Mixed operation for the connection of segments with different data transmission speeds is also supported. Switching properties -Multi-address function The switch can store up to 8192 MAC addresses in its address table. -Quality of service In case of heavy traffic, packets tagged with higher priority 802.1Q or Differentiated Services values will be given preference. The switch has four internal priority queues. -Multicast filtering The multicast filter will block PROFINET PTCP-Delay traffic. This is accomplished by filtering frames with the destination MAC address in the range 01-80-C2-00-00-02 through 01-80-C2-00-00-0F. Note that the filter blocks LLDP traffic because PTCP-Delay uses the same MAC address, 01-80C2-00-00-0E. -Alarm contact The switch provides contacts (R1, R2) for remote alarms if a failure is detected. Alarms are triggered if one or both power supplies fail. An alarm can be triggered if a port link is lost. Individual port alarms can be enabled via a DIP switch located on the bottom of the switch. The alarm relay is a normally closed type. When there are no faults, the contact is held open. When a fault occurs, the relay is de-energized to close the contact. -Link monitor DIP switch To enable an alarm for a port, move the appropriate slider to the ON position. To disable an alarm, move the appropriate slider to the OFF position. Power connection is via a removable COMBICON connector. US1 and US2 are 24 V DC and GND is 0 V DC.  FE, functional earth.   Product Features  All ports offer transmission speeds of 1000 Mbps  Jumbo frame support (frame size up to 10,240 bytes/frame)  QoS-prioritized (Quality of Service) messages  The switch also offers cable locking and port blocking  Alarm contact for power supply and link status diagnostics  Wide operating temperature range (-40°C ... +75°C)     10/21/2015   Page 1 / 4 https://www.phoenixcontact.com/us/products/2891390 Industrial Ethernet Switch - FL SWITCH SFNT 5GT - 2891390 Key Commercial Data Packing unit 1 pc Weight per Piece (excluding packing) 520.0 g Custom tariff number 85176200 Country of origin Taiwan Technical data Note Utilization restriction EMC: class A product, see manufacturer's declaration in the download area Dimensions Width 30 mm Height 130 mm Depth 100 mm Ambient conditions Degree of protection IP20 Ambient temperature (operation) -40 °C ... 75 °C Ambient temperature (storage/transport) -40 °C ... 85 °C Permissible humidity (operation) 5 % ... 95 % (non-condensing) Air pressure (operation) 62 kPa ... 108 kPa (up to 4850 m above mean sea level) Air pressure (storage/transport) 62 kPa ... 108 kPa (up to 4850 m above mean sea level) Interfaces Interface 1 Ethernet (RJ45) No. of ports 5 (RJ45 ports) Connection method RJ45 Note on connection method Auto negotiation and autocrossing Transmission physics Ethernet in RJ45 twisted pair Transmission speed 10/100/1000 MBit/s Function Basic functions Unmanaged switch / autonegotiation, complies with IEEE 802.3, store and forward switching mode, includes QoS and alarm contact Status and diagnostic indicators LEDs: US1, US2 (redundant voltage supply), link and activity per port, alarm (power and link down) Network expansion parameters Cascading depth Network, linear, and star structure: any Maximum conductor length (twisted pair) 100 m Supply voltage 10/21/2015   Page 2 / 4 https://www.phoenixcontact.com/us/products/2891390 Industrial Ethernet Switch - FL SWITCH SFNT 5GT - 2891390 Technical data Supply voltage Supply voltage 24 V DC (redundant) Residual ripple 3.6 VPP (within the permitted voltage range) Supply voltage range 10 V DC ... 60 V DC Typical current consumption typ. 223 mA (at US = 24 V DC) Max. current consumption 547 mA (10 V DC) Inrush surge current 7.2 A (400 μs) General Mounting type DIN rail Type AX Block design Net weight 525.6 g Housing material Aluminum Noise emission EN 61000-6-4 Classifications eCl@ss eCl@ss 5.1 19030117 eCl@ss 6.0 19170106 ETIM ETIM 5.0 EC000734 Approvals Approvals Approvals UL Listed / cUL Listed / cULus Listed Ex Approvals UL Listed / cUL Listed / cULus Listed Approvals submitted Approval details 10/21/2015   Page 3 / 4 https://www.phoenixcontact.com/us/products/2891390 Industrial Ethernet Switch - FL SWITCH SFNT 5GT - 2891390 Approvals UL Listed  cUL Listed  cULus Listed  Drawings Connection diagram + – + Connection diagram – + – US1 GND US2 GND R1 Redundant power supply connection R2 US1 GND US2 GND R1 R2 Single power supply connection Phoenix Contact 2015 © - all rights reserved http://www.phoenixcontact.com 10/21/2015   Page 4 / 4