2902823

MINI MCR-SL-CVS-24-5-10-NC Constant voltage source Data sheet 105264_en_01 1 © PHOENIX CONTACT 2013-04-03 Description Configurable constant voltage source for generating highprecision constant voltages. The voltage supply is also the input voltage. It is between 9.6 V DC and 30 V DC. The DIP switches accessible from the side of the housing allow configuration of the 10 V DC, 7.5 V DC, 5 V DC and 2.5 V DC output voltages. Features – – – Configurable constant voltage source Approval for Ex-zone 2 (nA) Screw or spring-cage connection can be provided Output and supply (input) are are electrically isolated from one another. NOTE: Correct usage in potentially explosive areas The module is a category 3 item of electrical equipment. It is absolutely vital to follow the instructions provided here during installation and observe the information in the "Safety regulations and installation notes". Make sure you always use the latest documentation. It can be downloaded from the product at phoenixcontact.net/products. This data sheet is valid for all products listed on the following page: MINI MCR-SL-CVS-24-5-10-NC 2 Table of contents 1 Description .............................................................................................................................. 1 2 Table of contents ..................................................................................................................... 2 3 Ordering data .......................................................................................................................... 3 4 Technical data ......................................................................................................................... 4 5 Safety regulations and installation notes.................................................................................. 6 5.1 Installation notes ................................................................................................................. 6 5.2 Installation in the Ex area (zone 2)............................................................................................ 6 6 Installation ............................................................................................................................... 7 6.1 Structure ........................................................................................................................... 7 6.2 Block diagram ..................................................................................................................... 7 6.3 Power supply ...................................................................................................................... 7 6.4 Assembly........................................................................................................................... 8 6.5 Connecting the wires ............................................................................................................ 8 7 Configuration ........................................................................................................................... 9 7.1 Configuration table ............................................................................................................... 9 8 Adjustment .............................................................................................................................. 9 105264_en_01 PHOENIX CONTACT 2 MINI MCR-SL-CVS-24-5-10-NC 3 Ordering data Description Type Order No. Pcs. / Pkt. Constant voltage source, input voltage 9.6 - 30 V DC, output voltage 10 V, 7.5 V, 5 V, 2.5 V DC, electrically isolated, can be configured via DIP switches, screw connection technology, standard configuration MINI MCR-SL-CVS-24-5-10-NC 2902822 1 Constant voltage source, input voltage 9.6 - 30 V DC, output voltage 10 V, 7.5 V, 5 V, 2.5 V DC, electrically isolated, can be configured via DIP switches, spring cage connection technology, standard configuration MINI MCR-SL-CVS-24-5-10-SP-NC 2902823 1 Constant voltage source, input voltage 9.6 - 30 V DC, output voltage 10 V, 7.5 V, 5 V, 2.5 V DC, electrically isolated, can be configured via DIP switches, spring cage connection technology, standard configuration MINI MCR-SL-CVS-24-5-10-SP-NC 2902823 1 Accessories Type Order No. Pcs. / Pkt. DIN rail connector (TBUS), 5-pos., for bridging the supply voltage, can be snapped onto NS 35/... DIN rails according to EN 60715 ME 6,2 TBUS-2 1,5/5-ST-3,81 GN 2869728 10 MCR power terminal block for supplying several MINI Analog modules via the T-connector, with screw connection, maximum current consumption of up to 2 A MINI MCR-SL-PTB 2864134 1 MCR power terminal block for supplying several MINI Analog modules via MINI MCR-SL-PTB-SP the T-connector, with spring-cage connection, maximum current consumption of up to 2 A 2864147 1 DIN rail power supply unit, primary-switched mode, slim design, output: 24 V DC / 1.5 A MINI-SYS-PS-100-240AC/24DC/1.5 2866983 1 DIN rail power supply unit, primary-switched mode, slim design, output: 24 V DC / 1.5 A, ATEX approval MINI-PS-100-240AC/24DC/1.5/EX 2866653 1 Eight MINI analog signal converters with screw connection method can be connected to a control system using a system adapter and system cabling with a minimum of wiring and very low error risk. MINI MCR-SL-V8-FLK 16-A 2811268 1 Fold up transparent cover for MINI MCR modules with additional labeling option using insert strips and flat Zack marker strip 6.2 mm MINI MCR DKL 2308111 10 Label for extended marking of MINI MCR modules in connection with the MINI MCR-DKL MINI MCR-DKL-LABEL 2810272 10 105264_en_01 PHOENIX CONTACT 3 MINI MCR-SL-CVS-24-5-10-NC 4 Technical data Input Voltage input signal 9.6 V DC ... 30 V DC Output Max. voltage output signal 10 V DC 7.5 V DC 5 V DC 2.5 V DC Configurable/programmable Yes, preconfigured Short-circuit current approx. 32 mA Ripple < 20 mVPP Supply Nominal supply voltage 24 V DC Supply voltage range 9.6 V DC ... 30 V DC (The T connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715)) Max. current consumption < 25 mA (10 V output with 30 mA load at 24 V DC IN) < 65 mA (10 V output with 30 mA load at 9.6 V DC IN) < 50 mA (10 V voltage output with 30 mA load at 12 V DC IN) < 20 mA (10 V voltage output with 30 mA load at 30 V DC IN) Power consumption < 600 mW (at 24 V IN) < 624 mW (at 9.6 V IN) < 564 mW (At 12 V IN) < 540 mW (At 30 V IN) General data Maximum transmission error ≤ 0.1 % (of final value) ≤ 0.5 % (Without adjustment) Temperature coefficient, typical < 0.002 %/K Maximum temperature coefficient < 0.01 %/K Electrical isolation Basic insulation according to EN 61010 Surge voltage category II Mounting position Any Degree of protection IP20 Pollution degree 2 Rated insulation voltage 50 V AC/DC Dimensions W / H / D 6.2 mm / 93.1 mm / 102.5 mm Type of housing PBT green Connection data Screw connection Spring-cage conn. Conductor cross section, solid 0.2 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² Conductor cross section, stranded 0.2 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² Stripping length 12 mm 8 mm Ambient conditions Ambient temperature (operation) -20 °C ... 65 °C Ambient temperature (storage/transport) -40 °C ... 85 °C 105264_en_01 PHOENIX CONTACT 4 MINI MCR-SL-CVS-24-5-10-NC Conformance with EMC Directive 2004/108/EC Noise immunity according to EN 61000-6-2 When being exposed to interference, there may be minimal deviations. Noise emission according to EN 61000-6-4 Conformance / approvals Conformance CE-compliant ATEX  II 3 G Ex nA IIC T4 Gc X UL, USA / Canada 508 listed UL, USA / Canada Class I, Div. 2, Groups A, B, C, D T5 applied for 105264_en_01 PHOENIX CONTACT 5 MINI MCR-SL-CVS-24-5-10-NC 5 Safety regulations and installation notes 5.1 Installation notes – – – – – The category 3 device is suitable for installation in the zone 2 potentially explosive area. It fulfills the requirements of EN 60079-0:2009 and EN 60079-15:2010. Installation, operation, and maintenance may only be carried out by qualified electricians. Follow the installation instructions described. When installing and operating the device, the applicable regulations and safety directives (including national safety directives), as well as general technical regulations, must be observed. The technical data is provided in this package slip and on the certificates (conformity assessment, additional approvals where applicable). It is not permissible to open or modify the device. Do not repair the device yourself but replace it with an equivalent device. Repairs may only be carried out by the manufacturer. The manufacturer is not liable for damage resulting from violation. The IP20 degree of protection (IEC 60529/EN 60529) of the device is intended for use in a clean and dry environment. Do not subject the device to any load that exceeds the described limits. The device is not designed for use in atmospheres with a danger of dust explosions. 105264_en_01 5.2 – – – – – – Installation in the Ex area (zone 2) Observe the specified conditions for use in potentially explosive areas. The device must be installed in a housing (control or distributor box) which meets the requirements of EN 60079-15 and provides at least IP54 (EN 60529) degree of protection. During installation and when connecting the supply and signal circuits, observe the requirements of EN 6007914. Devices may only be connected to circuits in zone 2 if they are suitable for operation in Ex zone 2 and for the prevailing conditions at the place of use. In potentially explosive areas, terminals may only be snapped onto or off the DIN rail connector and wires may only be connected or disconnected when the power is switched off. The device must be stopped and immediately removed from the Ex area if it is damaged, has been subjected to an impermissible load, has been stored incorrectly, or if it malfunctions. You can download the latest documents for these devices from www.phoenixcontact.net/products. PHOENIX CONTACT 6 MINI MCR-SL-CVS-24-5-10-NC 6 6.2 Installation Block diagram OUT NOTE: electrostatic discharge! The device contains components that can be damaged or destroyed by electrostatic discharge. When handling the device, observe the necessary safety precautions against electrostatic discharge (ESD) according to EN 61340-5-1 and EN 61340-5-1. 6.1 + 1 – 2 + 3 – 4 Structure 3 2 OUT U GND 1 +24V OUT OUT U GND 1 O DC , 7,5 0V DC ...3 5V 9°F 9,6 VDC, C ...+14 2,5 0VD -4° IN: : 9,6...3 °C / T OU = IN: °...+65 + –20 TU 1 OU Tamb OU + TU GN +24V GND 2 GN +24 V +24 ND 2 G 7 o. ial N Structure Output: constant voltage Potentiometer for adjustment Cover Groove for ZBF 6 zack marker strip Input/supply voltage Connection for DIN rail connector Universal snap-on foot for EN DIN rails DIP switch S1 105264_en_01 8 G Gc X II 3 A II C T4 Ex n D2 6 1. 2. 3. 4. 5. 6. 7. 8. 6.3 + 8 Ser Figure 1 5 D2 4 1 GN Block diagram Power supply - V 3 V 7 www.phoenixcontact.com D1 2 Figure 2 D1 - 6 5 GN +24 5 8 – Zone 2 Warning – Do n ot seperate when energized 1 , 10 C VD FF S1 7 + GND 2 4 y an rm -NC Ge 10 rg, 4-52 2 lo VS- 82 t B 2 5 tan rce L-C 0 82 32 R-S .: 29 Cons Sou C o ge lta I M rd.–N C Vo VD MIN O ON 6 – +24V GND 2 1 e mb 5 + NOTE: Never connect the supply voltage directly to the DIN rail connector. It is not permitted to draw power from the DIN rail connector or from individual modules. Supply via the MINI Analog Module Where the total current consumption of the aligned modules does not exceed 400 mA, the power can be supplied directly at the connection terminal blocks of the module. A 400 mA fuse should be connected upstream. Supply via a power terminal block The MINI MCR-SL-PTB power terminal block (Order No. 2864134) or the MINI MCR-SL-PTB-SP power terminal block (Order No. 2864147), which are the same shape, are used to feed the supply voltage to the DIN rail connector. A 2 A fuse should be connected upstream. Supply via a system power supply unit The system power supply unit with 1.5 A output current connects the DIN rail connector to the supply voltage and can thus be used to supply several modules from the mains. – MINI-SYS-PS-100-240AC/24DC/1.5 (Order No. 2866983) – Potentially explosive areas: MINI-PS-100-240AC/24DC/1.5/EX (Order No. 2866653) PHOENIX CONTACT 7 MINI MCR-SL-CVS-24-5-10-NC 6.4 Assembly Screw connection: B A B A D www.interface.phoenixcontact.com C E Figure 4 • • Figure 3 – 6.5 Insert the wire into the corresponding connection terminal block. Use a screwdriver to tighten the screw in the opening above the connection terminal block. Spring-cage connection: Mount the module on a 35 mm DIN rail according to EN 60715. When using the DIN rail connector, first place it into the DIN rail (see A – C). It is used to bridge the power supply. It is also absolutely vital that you snap the module and the DIN rail connector into position in the correct direction: the snap-on foot should be at the bottom and the connector on the left. A B Connecting the wires The MINI MCR-SL-CVS-24-5-10... is available in two connection versions: – Screw terminal blocks (MINI MCR-SL-CVS-24-5-10NC) – Spring-cage terminal blocks (MINI MCR-SL-CVS-24-510-SP-NC) Seri Figure 5 • • 105264_en_01 Screw connection www.interface.phoenixcontact.com – Mounting and removing X XXX XXX o. X al N Seri o. X al N XXX XXX X Spring-cage connection Insert a screwdriver into the opening above the connection terminal block. Insert the wire into the corresponding connection terminal block. PHOENIX CONTACT 8 MINI MCR-SL-CVS-24-5-10-NC 7 Configuration You set the constant output voltage with DIP switch S1 (see table). Standard Configuration If it is an "NC version", the device has the standard configuration: 10 V constant output voltage (all DIP switches in the "off" position). 7.1 Configuration table • = ON OUT 8 10 V 7.5 V 5V 2.5 V DIP S1 1 2 • • • • Adjustment A potentiometer is located underneath the cover; this is used for fine adjustment of the analog signals once the configuration of the DIP switches has been modified. The transmission error without adjustment is