PS-LD0605-01S

LED-CONVERTER UNIT PS-LD0605-01(S) (4.5 W) DESCRIPTION : This low profile LED-Converter is developed for max. 6 LED-lines APPLICABLE: 1~6 LED lines (Serial Mode) Pout max. 0,9 Watt per line, total max. 4,5 Watt LED Voltage max. 27V Lamp Current max. 60 mAdc per line FEATURES : Internal Open LED Detection for every Line Voltage or ext. PWM Dimming 1000:1 dimming ratio with external PWM Remote ON / OFF Wide Input Voltage Range RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity Connector style (PRELIMINARY INFORMATION) Pin-terminal style -20°C ~ +70°C -20°C ~ +85°C 95 %RH max DIMENSIONS : LxWxH 64 x 32 x 9.5 mm Weight :9 (g) typ. Pin terminal length may differ Components No. 1 2 3 Part Description PCB Connector CN1 Connector CN3 Qty. 1 1 1 Material UL94V-0 (FR-4 or CEM-3) 53261-0890 53261-0790 Note t=1.0mm Molex JST Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (1) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.0, 15th June 2009 All specifications are subject to change without notice. LED-CONVERTER UNIT PS-LD0605-01(S) (4.5 W) Input side CN1 Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 CN 1-6 CN 1-7 CN 1-8 Symbols Ratings Vin 4.75 ~ 5.25 Vdc Vin 4.75 ~ 5.25 Vdc Vrmt 0 ~ 0.8 = OFF / 2.5 ~ Vin = ON Ext. PWM 0 ~ 0.5 = LOW / 2.5 ~ 5 = HIGH Vbr 0.0 ~ 5.0 (5V=low brightness) GND GND GND Pin No. CN3 / 4-1 CN3 / 4-2 CN3 / 4-3 CN3 / 4-4 CN3 / 4-5 CN3 / 4-6 CN3 / 4-7 (PRELIMINARY INFORMATION) Output side CN3 / CN4 Symbols RTN6 (-) RTN5 (-) RTN4 (-) RTN3 (-) RTN2 (-) RTN1 (-) Ratings LED LINE 6 RETURN LED LINE 5 RETURN LED LINE 4 RETURN LED LINE 3 RETURN LED LINE 2 RETURN LED LINE 1 RETURN Vhigh (+) max 27Vdc (max.27mAdc) Output Current Select Control Jumper JP 1 Break Break Break Break Break JP 2 JP 3 JP 4 JP 5 Output Current +2 mA +4 mA +6 mA +8 mA +10 mA Example: 30mA (Output Current Min.) + 2mA (JP1) = 32mA 30mA (Output Current Min.) + 8mA (JP4) = 38mA JP1 ~ JP5 OPEN = 60mA For more information, please visit our web-site. ELECTRICAL CHARACTERISTICS : Conditions Parameters Output Current Output Current Input Current Open Load Shutdown PWM Frequency Output Power Output Power Output Power Output Power Symbols Iout Imin Iin Vbias f(PWM) Pout Pout Pout Pout Vin (V) 4.75 ~ 5.25 4.75 ~ 5.25 4.75 ~ 5.25 4.75 ~ 5.25 4.75 ~ 5.25 4.75 ~ 5.25 4.75 ~ 5.25 4.75 ~ 5.25 4.75 ~ 5.25 Vbr (V) 0 5 0 0 0 0 0 0 0 Tu (°C) -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+50 -20~+70 Min. 28 0.06 150 TBD TBD TBD TBD Specification Typ. 30 10 27 3 1.9 0.9 0.6 Max. 32 0.3 300 TBD TBD TBD TBD Unit mAdc % Adc Vdc Hz Watt Watt Watt Watt Note Duty 100% max current , duty cycle Tu: -20~+50degC Tu: -20~+70degC For one line For one line Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (2) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.0, 15th June 2009 All specifications are subject to change without notice. LED-CONVERTER UNIT PS-LD0605-01(S) (4.5 W) TEST CIRCUIT : (PRELIMINARY INFORMATION) Connect Vbr to Ground while using ext. PWM dimming. Note 1 : Note 2 : Note 3 : Note 4 : Note 5: Note 6 : ORDER KEY : Do not use analog dimming function and external PWM for dimming at the same time. Pin terminal style converters have Molex connectors mounted. Above output current is the default value. Correct output current is to be selected by user and under his sole responsibility. Exceeding currents will damage the LED backlight. External PWM-signal is LOW active. Do not use output 1 in case you connect only 5 (or less) outputs. Examples: Use 4 outputs only 1 then connect Pin 2+3+4+5. In case customer do not connect all output, please ask factory. PS-LD0605-01-x-yyy With order of this converter please give the following key: -x to be replaced by: -1 for connectors -2 for Pin-Terminal in case of quantity orders (300+ pcs), a pre-configuration can be ordered: -yyy to be replaced by: three digit value for required output current per LED line (from 010 to 030 including) Attention: * if no value is mentioned, 10 mA output current per LED line will be set as default * a selection of incorrect LED current may decrease lifetime or destroy the backlight * orders for pre-configured converters can’t be cancelled Examples: PS-LD0605-01-1-034 (S) 34 mA output current PCB with connectors PS-LD0605-01-2-58 (S) 58 mA output current PCB with Pin-Terminal CABLES : for input: 500 mm, stripped and tinned ends, order key for output: 500 mm, stripped and tinned ends, order key Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (3) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.0, 15th June 2009 All specifications are subject to change without notice.