1SP0335D2S1-45

SCALE™-2 1SP0335x2x1-45 1SP0335x2x1-45 Data Sheet Compact, high-performance, plug-and-play single-channel IGBT driver based on SCALE™-2 technology for individual and parallel-connected modules in 2-level, 3-level and multilevel converter topologies Abstract The SCALE™-2 plug-and-play driver 1SP0335x2x1-45 is a compact single-channel intelligent gate driver designed for 4500V 130x140mm and 190x140mm IGBT modules. The master driver 1SP0335x2M1-45 features a fiber-optic interface. It can be used as stand-alone driver or in conjunction with up to three 1SP0335D2S145 slaves to drive up to four parallel-connected IGBT modules. The DC/DC power supply must be purchased as a separate unit (one per master driver). The turn-on and turn-off gate resistors as well as the auxiliary gate capacitor are not assembled in order to provide maximum flexibility. They must be assembled by the user before start of operation. Please refer to the paragraph on “Gate Resistor Assembly” for the recommended values. For drivers adapted to other types of high-power and high-voltage IGBT modules, refer to: www.power.com/gate-driver/go/plug-and-play Features Applications  Plug-and-play solution  Allows parallel connection of IGBT modules  For 2-level, 3-level and multilevel topologies  Fiber-optic links (master)  Built-in interface to 1SP0335D2S1 (slave)  Duty cycle 0...100%  Dynamic Advanced Active Clamping DA C  Dynamic IGBT short-circuit protection  Monitoring of supply voltage  Monitoring of gate voltage  Extremely reliable; long service life  Shortens application development time  Suitable for 4500V 130x140mm 2 and 190x140mm IGBT modules www.power.com/gate-driver  Traction  Railroad power supplies  Light rail vehicles  HVDC  Flexible AC transmission systems (FACTS)  Medium-voltage converters  Industrial drives  Wind-power converters  Medical applications  Research  And many others  Page 1 SCALE™-2 1SP0335x2x1-45 Data Sheet Safety Notice! The data contained in this data sheet is intended exclusively for technically trained staff. Handling all highvoltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive devices according to international standard IEC 60747-1, Chapter IX or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged. Important Product Documentation This data sheet contains only product-specific data. For a detailed description, must-read application notes and common data that apply to the whole series, please refer to the “Description & Application Manual for 1SP0335 SCALE-2 IGBT Drivers” on www.power.com/gate-driver/go/1SP0335. The gate resistors as well as the auxiliary gate capacitor on this gate driver are not assembled in order to provide maximum flexibility. For the values required for specific IGBT modules, refer to the paragraph on “Gate Resistor Assembly”. Use of gate resistors and gate auxiliary capacitors other than those specified may result in failure. Mechanical Dimensions Dimensions: Refer to the relevant “Description and Application Manual” Mounting principle: Connected to IGBT module with screws Fiber-Optic Interfaces (1SP0335x2M1) Interface Remarks Drive signal input Drive signal input Status output Status output 1SP0335V, fiber-optic receiver (Notes 1, 2) 1SP0335S, fiber-optic receiver (Notes 1, 2) 1SP0335V, fiber-optic transmitter (Notes 1, 3) 1SP0335S, fiber-optic transmitter (Notes 1, 3) Part type # HFBR-2522ETZ HFBR-2412Z HFBR-1522ETZ HFBR-1412Z Electrical Connectors Interface Remarks Power supply connector X1 Bus connectors X2 and X3 On-board connector (Note 4) On-board connectors (Note 5) www.power.com/gate-driver Part type # 214012 214013 Page 2 SCALE™-2 1SP0335x2x1-45 Data Sheet Absolute Maximum Ratings Parameter Remarks Supply voltage VDC Average supply current IDC Average supply current IDC Gate output power VDC to COM 1SP0335x2M1 only (Note 6) 1SP0335x2M1 with three 1SP0335D2S1 (Note 6) 1SP0335x2M1, Ta < 70°C (Note 7) 1SP0335x2M1, Ta = 85°C (Note 7) 1SP0335D2S1, Ta < 70°C (Note 8) 1SP0335D2S1, Ta = 85°C (Note 8) 1SP0335x2M1, Ta < 70°C (Note 28) 1SP0335x2M1, Ta = 85°C (Note 28) 1SP0335D2S1, Ta < 70°C (Note 28) 1SP0335D2S1, Ta = 85°C (Note 28) Note 9 Switching operation (Note 10) Off state (Note 11) Collector-emitter voltage Between parallel connected drivers (Note 12) Between parallel connected drivers (Note 13) X2 and X3, total RMS value (Note 14) X2 and X3, total peak value (Note 14) Gate output power Switching frequency f Switching frequency f Gate peak current Iout DC-link voltage Operating voltage Max. emitter-emitter voltage |dV/dt| Max. interface current Operating temperature Storage temperature Min Note 29 0 Max Unit -40 -40 30 V 215 mA 740 mA 3.5 W 2.5 W 3.3 W 2.3 W n.d. kHz n.d. kHz n.d. kHz n.d. kHz +35 A 3000 V 3550 V 4500 Vpeak 200 Vpeak 50 kV/μs 4 Arms 20 Apeak 85 °C 50 °C -35 Recommended Operating Conditions Power Supply Remarks Min Typ Max Unit Supply voltage VDC To COM 23.5 25 26.5 V www.power.com/gate-driver Page 3 SCALE™-2 1SP0335x2x1-45 Data Sheet Electrical Characteristics All data refer to +25°C and VDC = 25V unless otherwise specified Power Supply Remarks Supply current IDC Without load, only 1SP0335x2M1 Without load, per additional 1SP0335D2S1 Power Supply Monitoring Remarks Min Typ Max Unit Supply threshold Viso-Vee 12.1 11.5 0.35 5 4.7 0.15 12.6 12.0 13.1 12.5 5.15 4.85 5.3 5 Monitoring hysteresis Clear fault Set fault (Note 15) Set/clear fault Clear fault Set fault (Note 15) Set/clear fault V V V V V V Bus to 1SP0335D2S1 Remarks Min Typ Max Monitoring hysteresis Supply threshold Vee-VCOM Supply voltage Turn-off command Turn-on command To COM To COM Gate Monitoring Remarks Turn-on threshold VGE,on,min Turn-off threshold VGE,off,max Filter delay Gmean to E, set fault (Note 16) Gmean to E, set fault (Note 16) Turn-on (Note 16) Turn-off (Note 16) Short-circuit Protection Remarks Static Vce-monitoring threshold Response time Delay to IGBT turn-off Between auxiliary terminals (Note 17) DC-link voltage = 3000V (Note 18) DC-link voltage = 2000V (Note 18) DC-link voltage = 1500V (Note 18) DC-link voltage = 1000V (Note 18) After the response time (Note 19) Timing Characteristics Remarks Turn-on delay td(on) Turn-off delay td(off) Output rise time tr(out) Output fall time tf(out) Note 20 Note 20 G to E (Note 21) G to E (Note 21) www.power.com/gate-driver Min Typ Max 45 20 mA mA VDC 0 15 Min Typ Typ Max Typ 190 185 9 30 Unit V V μs μs Max 170 5.8 5.8 6.0 7.7 0.3 Min Unit V V V 12.9 -7.6 28 42 Min Unit Unit V μs μs μs μs μs Max Unit ns ns ns ns Page 4 SCALE™-2 1SP0335x2x1-45 Data Sheet Timing Characteristics Remarks Min Typ Transmission delay of fault state Delay to clear fault state Acknowledge delay time Acknowledge pulse width Note 22 After IGBT short circuit (Note 23) After gate-monitoring fault (Notes 23, 27) Note 24 On host side Gate Output Remarks Turn-on gate resistor Rg(on) Turn-off gate resistor Rg(off) Auxiliary gate capacitor Cge Gate voltage at turn-on Gate-voltage at turn-off Note Note Note Note Note 25 25 25 26 26 Max Unit 400 90 9 1 250 700 1050 ns μs μs ns ns Min Typ Max Unit not assembled not assembled not assembled 15 -10 Ω Ω nF V V Footnotes to the Key Data 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) The transceivers required on the host controller side are not supplied with the gate driver. It is recommended to use the same types as used in the gate driver. For product information refer to www.power.com/gate-driver/go/fiberoptics. The recommended transmitter current at the host controller is 20mA. A higher current may increase jitter or delay at turn-off. The typical transmitter current at the gate driver is 18mA. In case of supply undervoltage, the minimum transmitter current at the gate driver is 12mA: this is suitable for adequate plastic optical fibers with a length of up to 10 meters. This refers to the manufacturer ordering number, see www.power.com/gate-driver/go/ext_erni. The customer-side connector as well as cables with different lengths can be supplied by Power Integrations. Refer to the “Description & Application Manual for 1SP0335 SCALE-2 IGBT Drivers” for more information. This refers to the manufacturer ordering number, see www.power.com/gate-driver/go/ext_erni. These connectors are to be used to connect 1SP0335x2M1 (master) or 1SP0335D2S1 (slave) to 1SP0335D2S1 (slave) if parallel connection of IGBT modules is required. Cables with different lengths can be supplied by Power Integrations. Refer to the “Description & Application Manual for 1SP0335 SCALE-2 IGBT Drivers” for more information. If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is not protected against overload. The given power can only be fully exploited without slaves 1SP0335D2S1 (no parallel connection of IGBT modules). If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is not protected against overload. From 70°C to 85°C, the maximum permissible output power can be linearly interpolated from the given data. The given power can be fully exploited with slaves 1SP0335D2S1 (parallel connection of IGBT modules). If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is not protected against overload. From 70°C to 85°C, the maximum permissible output power can be linearly interpolated from the given data. The gate current is limited by the gate resistors located on the driver. This limit is due to active clamping under switching conditions. Refer to the “Description & Application Manual for 1SP0335 SCALE-2 IGBT Drivers”. Due to the Dynamic Active Advanced Clamping Function (DA 2C) implemented on the driver, the DClink voltage can be increased in the off-state condition (e.g. after emergency shut-down). This value is only valid when the IGBTs are in the off state (not switching). The time during which the voltage can be applied should be limited to short periods (< 60 seconds). Refer to the “Description & Application Manual for 1SP0335 SCALE-2 IGBT Drivers”. www.power.com/gate-driver Page 5 SCALE™-2 1SP0335x2x1-45 Data Sheet 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 22) 23) 24) 25) 26) 27) 28) 29) The maximum dynamic voltage between auxiliary emitters of parallel-connected drivers due to asymmetrical operation at turn-on and turn-off must be limited to the given value. Maximum allowed rate of change of auxiliary emitter voltage of parallel connected drivers. This specification guarantees that the drive information will be transferred reliably even with high rate of change of auxiliary emitter voltages (asymmetrical operation). Dynamic voltages between auxiliary emitters of parallel connected drivers at turn-on and turn-off lead to equalizing currents over the X2 or X3 bus. The peak and RMS values of the resulting current must be limited to the given value. Undervoltage monitoring of the secondary-side supply voltage (Viso to Vee and Vee to COM which correspond with the approximate turn-on and turn-off gate-emitter voltages). If the corresponding voltage drops below this limit on 1SP0335x2M1 (masters), all paralleled IGBTs (master and slaves) are switched off and a fault is transmitted to the status output. If the corresponding voltage drops below this limit on 1SP0335D2S1 (slaves), the corresponding IGBT is switched off. If the IGBT was turned on, a fault will be generated by the gate-monitoring function on the master which will turn off all paralleled IGBT after the corresponding delay. The mean value VGE,mean of all gate voltages (master and all slaves) is filtered and compared to the given values at turn-on and turn-off. If the specified values are exceeded (V GE,meanVGE,off,max at turn-off) after the given filter delay, the driver turns off all parallelconnected IGBTs and a fault is transmitted to the status output. A dynamic Vce protection is implemented on the driver. The maximum allowed Vce voltage at turn-on is dynamically adjusted in order to better fit to the IGBT characteristics at turn-on. At the end of the turn-on process the given static value applies. The resulting pulse width of the direct output of the gate drive unit for short-circuit type I (excluding the delay of the gate resistors) is the sum of the response time plus the delay to IGBT turn-off. The turn-off event of the IGBT is delayed by the specified time after the response time. Including the delay of the external fiber-optic links (cable length: 1m). Measured from the transition of the turn-on or turn-off command at the optical transmitter on the host controller side to the direct output of the gate drive unit (excluding the delay of the gate resistors). Output rise and fall times are measured between 10% and 90% of the nominal output swing. The values are given for the driver side of the gate resistors with 2Ω/1uF load. The time constant of the output load in conjunction with the present gate resistors leads to an additional delay at their load side. Delay of external fiber-optic links. Measured from the driver secondary side (ASIC output) to the optical receiver on the host controller (cable length: 1m). Measured on the host side. The fault status on the secondary side is automatically reset after the specified time. Including the delay of the external fiber-optic links (cable length: 1m). Measured from the transition of the turn-on or turn-off command at the optical transmitter on the host controller side to the transition of the acknowledge signal at the optical receiver on the host controller side. The gate resistors and the auxiliary gate capacitor are not assembled on this IGBT gate driver. They must be assembled by the user according to the paragraph on “Gate Resistor Assembly”. The driver supply voltage VDC is split into two distinct voltages on the driver. The first one is the turnon voltage which is regulated at about 15V. The difference between VDC and the turn-on voltage is the turn-off voltage which is not regulated and mainly dependent on the driver input voltage VDC. The fault status is set as long as the gate monitoring fault is present. The given value applies if the driver goes from the “off state” to the “on state” and the gate-emitter voltage of one or more parallel connected drivers does not turn on. If the driver goes from the “on state” to the “off state” and the gate-emitter voltage of one or more parallel connected drivers does not turn off, the fault status is applied as long as the gate monitoring fault is present. The maximum switching frequency is not defined, as it depends on the IGBT module used. Please consult the corresponding driver data sheet for more information. The storage temperature inside the original package must be limited to the given value. Otherwise, it is limited to 90°C. www.power.com/gate-driver Page 6 SCALE™-2 1SP0335x2x1-45 Data Sheet Gate Resistor and Auxiliary Gate Capacitor Assembly The turn-on and turn-off gate resistors as well as the auxiliary gate capacitor of 1SP0335x2x1 drivers are adapted to their respective IGBT modules. Recommended gate resistors (R168, R169, R178 and R179): PR02 / 2W / 5% from Vishay Recommended auxiliary gate capacitor (C105): 1206 / X7R / 25V / 5% The following versions exist1: 4500V IGBT Type R178/ R179 CM600HG-90H 30Ω 30Ω 15Ω 15Ω not assembled 4.3Ω 5.6Ω 2.15Ω 2.8Ω 150nF 4.3Ω 5.6Ω 2.15Ω 2.8Ω 150nF 5.1Ω 16Ω 2.55Ω 8Ω not assembled 10Ω 13Ω 5Ω 6.5Ω 68nF 20Ω 24Ω 10Ω 12Ω not assembled THT gate resistors cannot be used (mechanical conflict). Please contact the technical support. 5SNA0650J450300 5SNA0800J450300 FZ800R45KL3_B5 MBN800H45E2-H CM900HG-90H MBN1000FH45F-H 5SNA1200G450300, 5SNA1200G450350 DIM1200ASM45-TS001 DIM1200ASM45-TF001 MBN1200H45E2-H FZ1200R45KL3_B5 3Ω R168/ R169 3.9Ω 5.1Ω 6.8Ω 5.1Ω 8.2Ω 8.2Ω 9.1Ω 1.3Ω 12Ω 5.6Ω 24Ω CM1200HG-90R CM1500HG-90X 5.1Ω 62Ω MBN1500FH45F 6.8Ω 6.8Ω MBN1500FH45F-H 6.8Ω 6.8Ω For the component position, refer to Figs. 1 and 2. 1 Resulting Rg,on Resulting Rg,off C105 1.5Ω 1.95Ω 220nF 2.55Ω 2.55Ω 4.1Ω 0.65Ω 2.8Ω 2.55Ω 3.4Ω 3.4Ω 3.4Ω 4.1Ω 4.55Ω 6Ω 12Ω 31Ω 3.4Ω 3.4Ω 220nF 220nF not assembled not assembled not assembled not assembled not assembled not assembled Note that the Rg,on and Rg,off values resulting from the THT versions may differ slightly from the SMD versions. www.power.com/gate-driver Page 7 SCALE™-2 1SP0335x2x1-45 Data Sheet Assembly Drawing Fig. 1: Assembly drawing of 1SP0335x2M1 with highlighted gate resistors Fig. 2: Assembly drawing of 1SP0335D2S1 with highlighted gate resistors Note that the wires of the gate resistors should not project more than 1.6mm after soldering (excess length at bottom side). Furthermore, a minimum distance of 1mm must be maintained between the gate resistor body and the PCB. Legal Disclaimer The statements, technical information and recommendations contained herein are believed to be accurate as of the date hereof. All parameters, numbers, values and other technical data included in the technical information were calculated and determined to our best knowledge in accordance with the relevant technical norms (if any). They may base on assumptions or operational conditions that do not necessarily apply in general. We exclude any representation or warranty, express or implied, in relation to the accuracy or completeness of the statements, technical information and recommendations contained herein. No responsibility is accepted for the accuracy or sufficiency of any of the statements, technical information, recommendations or opinions communicated and any liability for any direct, indirect or consequential loss or damage suffered by any person arising therefrom is expressly disclaimed. www.power.com/gate-driver Page 8 SCALE™-2 1SP0335x2x1-45 Data Sheet Ordering Information Our international terms and conditions of sale apply. Interface Master, Fiber-Optic Interface Master, Fiber-Optic Interface Slave, Electrical Interface 1) 2) 1) 2) Power Integrations Driver Type # Related IGBT 1SP0335V2M1-45 1SP0335S2M1-45 1SP0335D2S1-45 4500V IGBT modules 4500V IGBT modules 4500V IGBT modules Fiber-optic interface with versatile link (HFBR-2522ETZ and HFBR-1522ETZ) Fiber-optic interface with ST (HFBR-2412Z and HFBR-1412Z) See “Description & Application Manual for 1SP0335 SCALE-2 IGBT Drivers” Product home page: www.power.com/gate-driver/go/1SP0335 Refer to www.power.com/gate-driver/go/nomenclature for information on driver nomenclature Information about Other Products For other drivers, evaluation systems, product documentation and application support Please click onto: www.power.com/gate-driver © 2010…2020 Power Integrations Switzerland GmbH. We reserve the right to make any technical modifications without prior notice. www.power.com/gate-driver All rights reserved. Version 2.6 from 2020-03-26 Page 9 SCALE™-2 1SP0335x2x1-45 Data Sheet Power Integrations Sales Offices WORLD HEADQUARTERS 5245 Hellyer Avenue San Jose, CA 95138 USA Tel: +1-408-414-9200 Fax: +1-408-414-9765 Email: usasales@power.com AMERICAS EAST 7360 McGinnis Ferry Road Suite 225 Suwannee, GA 30024 USA Tel: +1-678-957-0724 Fax: +1-678-957-0784 Email: usasales@power.com AMERICAS CENTRAL 333 Sheridan Road Winnetka, IL 60093 USA Tel: +1-847-721-6293 Email: usasales@power.com AMERICAS WEST 5245 Hellyer Avenue San Jose, CA 95138 USA Tel: +1-408-414-8778 Fax: +1-408-414-3760 Email: usasales@power.com CHINA (Shanghai) Room 2410, Charity Plaza No. 88 North Caoxi Road Shanghai, 200030 China Tel: +86-21-6354-6323 Fax: +86-21-6354-6325 Email: chinasales@power.com CHINA (Shenzhen) 17/F, Hivac Building, No 2 Keji South 8th Road, Nanshan District Shenzhen, 518057 China Tel: +86-755-8672-8689 Fax: +86-755-8672-8690 Email: chinasales@power.com GERMANY (AC-DC/LED Sales) Einsteinring 24 85609 Aschheim, Germany Tel: +49-89-5527-39100 Fax: +49-89-1228-5374 Email: eurosales@power.com GERMANY (Gate Driver Sales) HellwegForum 1 59469 Ense, Germany Tel: +49-2938-64-39990 Email: gate-drivers.sales@power.com INDIA (Bangalore) #1, 14th Main Road Vasanthangar Bangalore, 560052 India Tel 1: +91-80-4113-8020 Tel 2: +91-80-4113-8028 Fax: +91-80-4113-8023 Email: indiasales@power.com INDIA (Mumbai) Unit: 106-107, Sagar Tech Plaza-B Sakinaka, Andheri Kurla Road Mumbai, Maharashtra 400072 India Tel 1: +91-22-4003-3700 Tel 2: +91-22-4003-3600 Email: indiasales@power.com INDIA (New Delhi) #45, Top Floor Okhla Industrial Area, Phase - III New Delhi, 110020 India Tel 1: +91-11-4055-2351 Tel 2: +91-11-4055-2353 Email: indiasales@power.com ITALY Via Milanese 20 20099 Sesto San Giovanni (MI), Italy Tel: +39-02-4550-8708 Email: eurosales@power.com JAPAN Kosei Dai-3 Bldg. 2-12-11, Shin-Yokohama, Kohoku-ku Yokohama-shi, Kanagawa Japan 222-0033 Tel: +81-45-471-1021 Fax: +81-45-471-3717 Email: japansales@power.com KOREA RM602, 6FL, 22 Teheran-ro 87-gil, Gangnam-gu Seoul, 06164 Korea Tel: +82-2-2016-6610 Fax: +82-2-2016-6630 Email: koreasales@power.com SINGAPORE 51 Newton Road #19-01/05 Goldhill Plaza Singapore, 308900 Tel 1: +65-6358-2160 Tel 2: +65-6358-4480 Fax: +65-6358-2015 Email: singaporesales@power.com TAIWAN 5F, No. 318, Nei Hu Rd., Sec. 1 Nei Hu Dist. Taipei, 114 Taiwan Tel: +886-2-2659-4570 Fax: +886-2-2659-4550 Email: taiwansales@power.com UNITED KINGDOM Building 5, Suite 21 The Westbrook Centre Milton Road Cambridge, CB4 1YG United Kingdom Tel: +44-7823-557-484 Email: eurosales@power.com www.power.com/gate-driver Page 10