USB0403_10

05205 Only One Name Means ProTek’Tion™ USB0403 - USB0424C 350 watt low CaPaCitanCe tvS aRRay DeSCRiPtion The USB04xx and USBxxC Series of devices are low capacitance TVS arrays available in a SOT-143 package. These devices are designed to protect Ethernet data I/O ports against the damaging effects of ESD and EFT transient threats. The USB04xx series are unidirectional devices used for common mode protection from line to ground. The USB04xxC series are bidirectional devices typically used for differential mode on balanced lines. Voltages range from 3.3 to 24 volts for both configurations. Each series provides ESD protection to > 25 kilovolts with a peak pulse power rating of 350 Watts for an 8/20µs waveshape. The USB04xx and USBxxC series are designed to meet and exceed the IEC 61000-4-2 and IEC 61000-4-4 requirements. Sot-143 PaCkage FeatUReS • Compatible with IEC 61000-4-2 (ESD): Air 15kV, Contact 8kV • Compatible with IEC 61000-4-4 (EFT): 40A, 5/50ns • Compatible with IEC 61000-4-5 (Surge): 12A, 8/20µs - Level 1(LineGnd) & Level 2(Line-Line) • 350 Watts Peak Pulse Power per Line (tp = 8/20µs) • Unidirectional and Bidirectional Configurations • Available in Multiple Voltages Ranging from 3V to 24V • Protects 1 Line • Low Leakage Current • Low Capacitance: 5pF per Line Pair • RoHS Compliant • REACH Compliant aPPliCationS • • • • Ethernet - 10/100/1000 Base T Cellular Phones Audio/Video Inputs FireWire, SCSI & USB Interfaces MeChaniCal ChaRaCteRiStiCS • • • • Molded JEDEC SOT-143 Package Approximate Weight: 9 milligrams Lead-Free Pure-Tin Plating (Annealed) Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270°C • 8mm Tape and Reel Per EIA Standard 481 • Flammability Rating UL 94V-0 Pin ConFigURationS 1 4 1 4 2 3 2 BIDIRECTIONAL 3 UNIDIRECTIONAL 05205.R5 10/10 Page 1 www.protekdevices.com 05205 Only One Name Means ProTek’Tion™ USB0403 - USB0424C tyPiCal DeviCe ChaRaCteRiStiCS MaXiMUM RatingS @ 25°C Unless otherwise Specified PaRaMeteR Operating Temperature Storage Temperature Peak Pulse Power (tp = 8/20µs) - See Figure 1 SyMBol TL TSTG PPP valUe -55 to 150 -55 to 150 350 UnitS °C °C Watts eleCtRiCal ChaRaCteRiStiCS PeR line @ 25°C Unless otherwise Specified PaRt nUMBeR (notes 1 - 2) DeviCe MaRking RateD StanD-oFF voltage MiniMUM BReakDown voltage @ 1ma v(BR) voltS 4.0 4.0 6.0 6.0 8.5 8.5 13.3 13.3 16.6 16.6 26.7 26.7 MaXiMUM ClaMPing voltage (Fig. 2) @ i P = 5a vC voltS 9.0 9.0 11.0 11.0 16.6 16.6 24.0 24.0 30.0 30.0 N/A N/A MaXiMUM ClaMPing voltage (See Fig. 2) @ 8/20µS vC @ i PP voltS 19.0V @ 20.0A 19.0V @ 20.0A 18.3V @ 17.0A 18.3V @ 17.0A 18.5V @ 17.0A 18.5V @ 17.0A 28.6V @ 11.0A 28.6V @ 11.0A 31.8V @ 10.0A 31.8V @ 10.0A 56.0V @ 6.0A 56.0V @ 6.0A MaXiMUM leakage CURRent @v wM iD µa 125 125 20 20 10 10 1 1 1 1 1 1 tyPiCal CaPaCitanCe @0v, 1Mhz vwM voltS USB0403 USB0403C USB0405 USB0405C USB0408 USB0408C USB0412 USB0412C USB0415 USB0415C USB0424 USB0424C noteS 3U 3B 5U 5B 8U 8B 12U 12B 15U 15B 24U 24B 3.3 3.3 5.0 5.0 8.0 8.0 12.0 12.0 15.0 15.0 24.0 24.0 C pF 5 5 5 5 5 5 5 5 5 5 5 5 1. Part numbers with an additional “C” suffix are bidirectional devices, i.e., USB0405C. 2. Unidirectional Only: Positive potential is applied from pin 2 to 1 or pin 3 to 4. 05205.R5 10/10 Page 2 www.protekdevices.com 05205 Only One Name Means ProTek’Tion™ USB0403 - USB0424C tyPiCal DeviCe ChaRaCteRiStiCS FigURe 1 Peak PUlSe PoweR vS PUlSe tiMe 10,000 PPP - Peak Pulse Power - watts 1,000 350W, 8/20µs Waveform 100 10 0.1 1 10 100 td - Pulse Duration - µs 1,000 10,000 120 iPP - Peak Pulse Current - % of iPP FigURe 2 PUlSe wave FoRM tf Peak Value IPP TEST WAVEFORM PARAMETERS tf = 8µs td = 20µs 100 80 % of Rated Power FigURe 3 PoweR DeRating CURve Peak Pulse Power 8/20µs 100 80 60 40 20 0 0 5 e-t 60 40 20 0 Average Power td = t/(IPP/2) 10 15 t - time - µs 20 25 30 0 25 50 75 100 125 ta - ambient temperature - °C 150 05205.R5 10/10 Page 3 www.protekdevices.com 05205 Only One Name Means ProTek’Tion™ USB0403 - USB0424C tyPiCal DeviCe ChaRaCteRiStiCS FigURe 4 oveRShoot & ClaMPing voltage FoR USB0405C 40 30 5 volts per Division 20 10 0 eSD test Pulse - 5 kilovolt, 1/30ns (waveshape) FigURe 5 inSeRtion loSS - USB0405C FigURe 6 RetURn loSS - USB0405C 20 10 db per Division 10 db per Division 100 Mhz per Division 20 Ref 0 Ref 0 -20 -20 -50 -50 100 Mhz per Division 05205.R5 10/10 Page 4 www.protekdevices.com 05205 Only One Name Means ProTek’Tion™ USB0403 - USB0424C SPiCe MoDel FigURe 1 SPiCe MoDel I/O LCRD LCRD ABD Lg 0.8nH LCRD Lg 0.65nH ABD ABD I/O LCRD UNIDIRECTIONAL BIDIRECTIONAL ABD - Avalanche Breakdown Diode (TVS) LCRD: Low Capacitance Rectifier Diode Lg - Lead Inductance taBle 1 - SPiCe PaRaMeteRS PaRaMeteR BV IBV Cjo IS Vj M N RS TT EG Unit V µA pF A V Ohms s eV aBD(tvS) See Table 2 1 See Table 2 See Table 2 0.6 0.33 1 See Table 2 1E-8 1.11 lCRD 200 0.01 5 1E-13 0.6 0.33 1 0.31 1E-9 1.11 PaRt nUMBeR USB0403 USB0405 USB0408 USB0412 USB0415 USB0424 USB0403C USB0405C USB0408C USB0412C USB0415C USB0424C 05205.R5 10/10 taBle 2 - aBD SPeCiFiC SPiCe PaRaMeteRS i S (aMPS) Bv(voltS) Cjo(pF) 4.5 6.0 8.5 13.3 16.7 26.7 4.5 6.0 8.5 13.3 16.7 26.7 200 140 67 55 47 28 200 140 67 55 47 28 Page 5 Rs(ohMS) 0.22 0.18 0.12 1.10 1.43 4.24 0.22 0.18 0.12 1.10 1.43 4.24 www.protekdevices.com 1E-11 1E-11 1E-11 1E-13 1E-13 1E-13 1E-11 1E-11 1E-11 1E-13 1E-13 1E-13 05205 Only One Name Means ProTek’Tion™ USB0403 - USB0424C aPPliCation inFoRMation GND SOLDER PAD 1 4 1 4 2 3 2 3 USB OUTPUT CONNECTOR D+ USB IC D- FigURe 1 - USB PRoteCtion Two USB04xx (Unidirectional) in a Common-Mode configuration. Circuit connectivity is as follows: • Device 1: Line 1(D+) is connected to pins 2 and 3. • Device 2: Line 2(D-) is connected to pins 2 and 3. • Device 1 and 2: Pins 1 and 4 connected to ground RX ETHERNET TRANSCEIVER R 2 3 TX FigURe 2 - etheRnet PRoteCtion One USB04xxC (Bidirectional) in a Differential-Mode configuration. Circuit connectivity is as follow: • Line 1 (RX) is connected to pins 1 and 4. • Line 2 (TX) is connected to pins 2 and 3. CiRCUit BoaRD ReCoMMenDationS Circuit board layout is critical for electromagnetic compatibility protection. The following guidelines are recommended: • The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. • The path length between the TVS device and the protected line should be minimized. • All conductive loops including power and ground loops should be minimized. • The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. • Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. RJ-45 R 1 4 05205.R5 10/10 Page 6 www.protekdevices.com 05205 Only One Name Means ProTek’Tion™ USB0403 - USB0424C Sot-143 PaCkage inFoRMation oUtline DiMenSionS DiM A B C D F G J K L L1 R S noteS A G L MilliMeteRS Min 2.80 1.20 0.84 0.39 0.79 1.78 0.08 0.46 0.445 0.40 0.72 2.11 inCheS Min 0.110 0.047 0.033 0.015 0.031 0.070 0.003 0.018 0.0175 0.016 0.028 0.083 MaX 3.04 1.39 1.14 0.50 0.93 2.03 0.15 0.60 0.60 0.60 0.83 2.48 MaX 0.120 0.055 0.045 0.020 0.037 0.080 0.006 0.024 0.024 0.024 0.033 0.098 H C F D BS L1 K J R 1. Dimensioning and tolerances per ANSI Y14.M, 1985. 2. Controlling dimension: inches. 3. Dimensions are exclusive of mold flash and metal burrs. PaD layoUt DiMenSionS DiM A B C D E F noteS C A MilliMeteRS Min 1.88 1.80 0.71 0.76 1.07 0.71 inCheS Min 0.074 0.071 0.028 0.030 0.042 0.028 MaX 2.13 2.06 0.97 1.02 1.32 0.97 MaX 0.084 0.081 0.038 0.040 0.052 0.038 E F D B 1. Controlling dimension: inches. 05205.R5 10/10 Page 7 www.protekdevices.com 05205 Only One Name Means ProTek’Tion™ USB0403 - USB0424C taPe anD Reel P0 t D P2 10 Pitches Cumulative Tolerance on Tape. ± 0.2 E Top Cover Tape A0 K0 Pin 1 F W B0 P User Direction of Feed SPeCiFiCationS Reel Dia. 178mm (7”) 1. 2. 3. 4. 5. taPe wiDth 8mm a0 B0 k0 D e F w P0 P2 P tmax 0.25 3.10 ± 0.10 2.70 ± 0.10 1.35 ± 0.10 1.50 ± 0.10 1.75 ± 0.10 3.50 ± 0.05 8.00 ± 0.30 4.00 ± 0.10 2.00 ± 0.05 4.00 ± 0.10 noteS Dimensions are in millimeters. Surface mount product is taped and reeled in accordance with EIA-481. Suffix - T7 = 7” Reel - 3,000 pieces per 8mm tape. Suffix - T13 = 13” Reel - 10,000 pieces per 8mm tape. Marking on Part - marking code (see page 2) and date code. Package outline, pad layout and tape specifications per document number 06011.R4 8/10. oRDeRing inFoRMation BaSe PaRt nUMBeR (xx = voltage) USB04xx/USB04xxC USB04xx/USB04xxC leaDFRee SUFFiX -LF -LF taPe SUFFiX -T7 -T13 Qty/Reel 3000 10,000 Reel SiZe 7” 13” tUBe Qty n/a n/a 05205.R5 10/10 Page 8 www.protekdevices.com 05205 Only One Name Means ProTek’Tion™ USB0403 - USB0424C CoMPany inFoRMation CoMPany PRoFile ProTek Devices, based in Tempe, Arizona USA, is a manufacturer of Transient Voltage Suppression (TVS) products designed specifically for the protection of electronic systems from the effects of lightning, Electrostatic Discharge (ESD), Nuclear Electromagnetic Pulse (NEMP), inductive switching and EMI/RFI. With over 25 years of engineering and manufacturing experience, ProTek designs TVS devices that provide application specific protection solutions for all electronic equipment/systems. ProTek Devices Analog Products Division, also manufactures analog interface, control, RF and power management products. ContaCt US Corporate headquarters 2929 South Fair Lane Tempe, Arizona 85282 USA By telephone General: 602-431-8101 Sales: 602-414-5109 Customer Service: 602-414-5114 By Fax General: 602-431-2288 By e-mail: Sales: sales@protekdevices.com Customer Service: service@protekdevices.com Technical Support: support@protekdevices.com web www.protekdevices.com www.protekanalog.com COPYRIGHT © ProTek Devices 2007 - This literature is subject to all applicable copyright laws and is not for resale in any manner. SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice. DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special, consequential or incidental damages. LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory. 05205.R5 10/10 Page 9 www.protekdevices.com