PE-1008CD390GTT

RF Chip Inductors Wire Wound - 1008 Series For More Information Please Visit: Networking.PulseElectronics.com WIRE WOUND RF CHIP INDUCTORS 1008CD SERIES Wire wound ceramic core construction High Q values High self resonant frequency Temperature Range -40 oC to +125 oC Industry 1008 ( 2520) size and surface mount land pattern 100% Tin Solder Termination Electrical Specifications @ 25°C - Operating Temperature Range -40 oC to +125oC PE-1008CD100GTT 10 @ 50MHz 50 @ 500MHz 4100.0 0.09 IDC 5 (mA MAX) 1000 PE-1008CD120GTT PE-1008CD180GTT 12 @ 50MHz 17, 8 @ 50MHz 50 @ 500MHz 50 @ 350MHz 3300.0 2500.0 0.09 0.11 1000 1000 PE-1008CD220GTT 22 @ 50MHz 55 @ 350MHz 1800.0 0.12 1000 PE-1008CD270GTT 27 @ 50MHz 55 @ 350MHz 1500.0 0.11 1000 PE-1008CD330GTT 33 @ 50MHz 60 @ 350MHz 1600.0 0.14 1000 PE-1008CD390GTT 39 @ 50MHz 60 @ 350MHz 1400.0 0.12 1000 PE-1008CD470GTT 47 @ 50MHz 65 @ 350MHz 1200.0 0.08 1000 PE-1008CD560GTT 56 @ 50MHz 65 @ 350MHz 1160.0 0.09 1000 PE-1008CD680GTT 68 @ 50MHz 65 @ 350MHz 1100.0 0.07 1000 PE-1008CD820GTT 82 @ 50MHz 60 @ 350MHz 950.0 0.14 1000 PE-1008CD101GTT 100 @ 25MHz 60 @ 350MHz 900.0 0.15 650 PE-1008CD121GTT 120 @ 25MHz 60 @ 350MHz 950.0 0.63 650 PE-1008CD151GTT PE-1008CD181GTT 150 @ 25MHz 45 @ 100MHz 625.0 0.16 580 180 @ 25MHz 45 @ 100MHz 650.0 0.77 620 PE-1008CD221GTT 220 @ 25MHz 45 @ 100MHz 625.0 0.84 500 PE-1008CD271GTT 270 @ 25MHz 45 @ 350MHz 525.0 0.91 500 PE-1008CD331GTT 330 @ 25MHz 45 @ 100MHz 500.0 1.05 450 PE-1008CD391GTT 390 @ 25MHz 45 @ 100MHz 475.0 1.12 470 PE-1008CD471GTT 470 @ 25MHz 45 @ 100MHz 450.0 1.19 420 PE-1008CD561GTT 560 @ 25MHz 415.0 1.33 310 PE-1008CD681GTT 680 @ 25MHz 45 @ 100MHz 45 @ 100MHz 375.0 1.47 230 PE-1008CD821GTT 820 @ 25MHz 45 @ 100MHz 350.0 1.61 180 Part Number Tolerance +/-2% Inductance 1 (nH) Q2 (MIN) SRF 3 (MHz MIN) RDC 4 (Ω MAX) (Continued on next page) Pulse Jack www.networking.pulseelectronics.com WC711.C (7/19) Electronics WIRE WOUND RF CHIP INDUCTORS 1008CD SERIES Electrical Specifications @ 25°C - Operating Temperature Range -40oC to +125oC Inductance 1 (nH) Q2 (MIN) SRF 3 (MHz MIN) RDC 4 (Ω MAX) IDC 5 (mA MAX) PE-1008CD102GTT 1000 @ 25MHz 35 @ 50MHz 260.0 1.90 120 PE-1008CD122GTT 1200 @ 7.9MHz 35 @ 50MHz 250.0 2.00 310 PE-1008CD152GTT PE-1008CD182GTT 1500 @ 7.9MHz 28 @ 50MHz 200.0 2.30 330 1800 @ 7.9MHz 28 @ 50MHz PE-1008CD222GTT 2200 @ 7.9MHz 28 @ 50MHz 160.0 80.0 2.60 2.80 300 280 PE-1008CD272GTT 2700 @ 7.9MHz 3300 @ 7.9MHz 22 @ 50MHz 90.0 3.20 290 22 @ 25MHz 40.0 3.40 290 PE-1008CD332GTT Notes: (continued) Part Number Tolerance +/-2% 1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that inductance information is not stamped on part, because of the extremely small size). 2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture 3. SRF measured using a HP8753C Network Analyzer. 4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter. 5. Based on a 15�C maximum temperature rise, Typical Q vs Frequency Typical Inductance vs Frequency Mechanical Pulse Jack Weight ..................0.032gram 3 Electronics Dimensions: www.networking.pulseelectronics.com Inches mm WC711.C (7/19) Unless otherwise specified, all tolerances are ± .010 0,25 WIRE WOUND RF CHIP INDUCTORS perFormanCe testing Electrical Testing Storage and Operating Temperature Range: -40oC to +125oC Inductors are subjected to the extremes for 48 hours. Then tested at 25 oC Thermal: Inductors are subjected to 30 cycles for 30 minutes at each extreme. -40oC to +85oC Then tested at 25 oC Moisture Resistance Inductors are subjected to 10 cycles of 24 hours at 70 oC with 90 to 95% Relative Humidity There shall be no deformation or change in appearance Inductance shall not change by more than ±5% Q values shall not change by more than ±10% Then tested at 24 oC Operating Life Inductors are subjected to 1000 hours at 85 oC with 85% Relative Humidity with the rated current applied There shall be no Damaged, Open or Shorted Windings Mechanical Testing Temperature Range: Inductors are subjected to the following: Use a solder pot at 260 oC, with RMA Flux. Each termination is immersed in 63Sn/37Pb molten solder for 4 to 6 seconds. There shall be no deformation or change in appearance Inductance shall not change by more than ±5% Q values shall not change by more than ±10% Recommended Solder Heat Resistance Profile Pulse Jack 4 Electronics www.networking.pulseelectronics.com WC711.C (7/19) WIRE WOUND RF CHIP INDUCTORS perFormanCe testing Physical Specifications Samplers are subjected to random vibrations as per NAVMAT P9492 Vibration (Random) There shall be no deformation or change in appearance Inductance shall not change by more than ±5% Mechanical Shock Inductors are subjected to one half sine wave pulse (8700 g's for 0.3ms) in each directional axis for a total of 18 shocks Q values shall not change by more than ±10% Moisture Resistance Reflow Inductors on to test pads using 63 Sn/37 Pb solder paste (IR Reflow profile : 200 oC for 30 seconds or peak 235 oC for 20 seconds) The inductors shall withstand a minimum force of 1000 g's in any direction using a dynamometer force guage. Tape and Reel Specifications Packing Moisture Level = MSL 1 - Storage Temperature - 40oC to +125oC Series Parts per Reel PE-1008CD 1600 Tape Dimensions (mm) Reels Dimensions (mm) A 178 B 50 C D E 13 14.4 8.4 W 8 P1 2 P2 4 P3 4 H T 2.6 0.3 Notes: P1, P2 and P3 are same for all chip inductor series. Keeping the same dimensions for guide hole and pocket pitch (P1), pocket pitch (P2), guide hold pitch (P3) and tape width (8mm) for all series, enables the packaging machine to maintain the same settings while changing models. The only difference between the series are the parts per reel which contributes to a different length of tapes/reel per model. Pulse Jack 5 www.networking.pulseelectronics.com WC711.C (7/19) Electronics