RF Chip Inductors
Wire Wound - 1008 Series
For More Information Please Visit: Networking.PulseElectronics.com
WIRE WOUND RF CHIP INDUCTORS
1008CD SERIES
Wire wound ceramic core construction
High Q values
High self resonant frequency
Temperature Range -40 oC to +125 oC
Industry 1008 ( 2520) size and surface
mount land pattern
100% Tin Solder Termination
Electrical Specifications @ 25°C - Operating Temperature Range -40 oC to +125oC
PE-1008CD100GTT
10 @ 50MHz
50 @ 500MHz
4100.0
0.09
IDC 5
(mA MAX)
1000
PE-1008CD120GTT
PE-1008CD180GTT
12 @ 50MHz
17, 8 @ 50MHz
50 @ 500MHz
50 @ 350MHz
3300.0
2500.0
0.09
0.11
1000
1000
PE-1008CD220GTT
22 @ 50MHz
55 @ 350MHz
1800.0
0.12
1000
PE-1008CD270GTT
27 @ 50MHz
55 @ 350MHz
1500.0
0.11
1000
PE-1008CD330GTT
33 @ 50MHz
60 @ 350MHz
1600.0
0.14
1000
PE-1008CD390GTT
39 @ 50MHz
60 @ 350MHz
1400.0
0.12
1000
PE-1008CD470GTT
47 @ 50MHz
65 @ 350MHz
1200.0
0.08
1000
PE-1008CD560GTT
56 @ 50MHz
65 @ 350MHz
1160.0
0.09
1000
PE-1008CD680GTT
68 @ 50MHz
65 @ 350MHz
1100.0
0.07
1000
PE-1008CD820GTT
82 @ 50MHz
60 @ 350MHz
950.0
0.14
1000
PE-1008CD101GTT
100 @ 25MHz
60 @ 350MHz
900.0
0.15
650
PE-1008CD121GTT
120 @ 25MHz
60 @ 350MHz
950.0
0.63
650
PE-1008CD151GTT
PE-1008CD181GTT
150 @ 25MHz
45 @ 100MHz
625.0
0.16
580
180 @ 25MHz
45 @ 100MHz
650.0
0.77
620
PE-1008CD221GTT
220 @ 25MHz
45 @ 100MHz
625.0
0.84
500
PE-1008CD271GTT
270 @ 25MHz
45 @ 350MHz
525.0
0.91
500
PE-1008CD331GTT
330 @ 25MHz
45 @ 100MHz
500.0
1.05
450
PE-1008CD391GTT
390 @ 25MHz
45 @ 100MHz
475.0
1.12
470
PE-1008CD471GTT
470 @ 25MHz
45 @ 100MHz
450.0
1.19
420
PE-1008CD561GTT
560 @ 25MHz
415.0
1.33
310
PE-1008CD681GTT
680 @ 25MHz
45 @ 100MHz
45 @ 100MHz
375.0
1.47
230
PE-1008CD821GTT
820 @ 25MHz
45 @ 100MHz
350.0
1.61
180
Part Number
Tolerance +/-2%
Inductance 1
(nH)
Q2
(MIN)
SRF 3
(MHz MIN)
RDC 4
(Ω MAX)
(Continued on next page)
Pulse Jack
www.networking.pulseelectronics.com
WC711.C (7/19)
Electronics
WIRE WOUND RF CHIP INDUCTORS
1008CD SERIES
Electrical Specifications @ 25°C - Operating Temperature Range -40oC to +125oC
Inductance 1
(nH)
Q2
(MIN)
SRF 3
(MHz MIN)
RDC 4
(Ω MAX)
IDC 5
(mA MAX)
PE-1008CD102GTT
1000 @ 25MHz
35 @ 50MHz
260.0
1.90
120
PE-1008CD122GTT
1200 @ 7.9MHz
35 @ 50MHz
250.0
2.00
310
PE-1008CD152GTT
PE-1008CD182GTT
1500 @ 7.9MHz
28 @ 50MHz
200.0
2.30
330
1800 @ 7.9MHz
28 @ 50MHz
PE-1008CD222GTT
2200 @ 7.9MHz
28 @ 50MHz
160.0
80.0
2.60
2.80
300
280
PE-1008CD272GTT
2700 @ 7.9MHz
3300 @ 7.9MHz
22 @ 50MHz
90.0
3.20
290
22 @ 25MHz
40.0
3.40
290
PE-1008CD332GTT
Notes:
(continued)
Part Number
Tolerance +/-2%
1. Inductance measured using a HP4286A RF Impedance Analyzer. (Please note that inductance information
is not stamped on part, because of the extremely small size).
2. Q measured using a HP4291A RF Impedance Analyzer with a HP16193A Test Fixture
3. SRF measured using a HP8753C Network Analyzer.
4. RDC measured using a Valhalla Scientific model 4100 ATC Digital Ohmeter.
5. Based on a 15�C maximum temperature rise,
Typical Q vs Frequency
Typical Inductance vs Frequency
Mechanical
Pulse Jack
Weight ..................0.032gram
3
Electronics
Dimensions:
www.networking.pulseelectronics.com
Inches
mm
WC711.C (7/19)
Unless otherwise specified,
all tolerances are ± .010
0,25
WIRE WOUND RF CHIP INDUCTORS
perFormanCe testing
Electrical Testing
Storage and Operating
Temperature Range:
-40oC to +125oC
Inductors are subjected to the extremes
for 48 hours.
Then tested at 25 oC
Thermal:
Inductors are subjected to 30 cycles for 30 minutes
at each extreme.
-40oC to +85oC
Then tested at 25 oC
Moisture Resistance
Inductors are subjected to
10 cycles of 24 hours at 70 oC with 90 to 95% Relative
Humidity
There shall be no deformation or change in
appearance
Inductance shall not change by more than
±5%
Q values shall not change by more than
±10%
Then tested at 24 oC
Operating Life
Inductors are subjected to 1000 hours at 85 oC
with 85% Relative Humidity with the rated
current applied
There shall be no Damaged, Open or
Shorted Windings
Mechanical Testing
Temperature Range:
Inductors are subjected to the following: Use a solder pot at
260 oC, with RMA Flux. Each termination is immersed in
63Sn/37Pb molten solder for 4 to 6 seconds.
There shall be no deformation or change in
appearance
Inductance shall not change by more than ±5%
Q values shall not change by more than ±10%
Recommended Solder Heat
Resistance Profile
Pulse Jack
4
Electronics
www.networking.pulseelectronics.com
WC711.C (7/19)
WIRE WOUND RF CHIP INDUCTORS
perFormanCe testing
Physical Specifications
Samplers are subjected to random vibrations as
per NAVMAT P9492
Vibration (Random)
There shall be no deformation or change in
appearance
Inductance shall not change by more than
±5%
Mechanical Shock
Inductors are subjected to one half sine wave pulse
(8700 g's for 0.3ms) in each directional axis for a total of
18 shocks
Q values shall not change by more than ±10%
Moisture Resistance
Reflow Inductors on to test pads using 63
Sn/37 Pb solder paste (IR Reflow profile :
200 oC for 30 seconds or
peak 235 oC for 20 seconds)
The inductors shall withstand a minimum
force of 1000 g's in any direction using a
dynamometer force guage.
Tape and Reel Specifications
Packing Moisture Level = MSL 1 - Storage Temperature - 40oC to +125oC
Series
Parts per
Reel
PE-1008CD
1600
Tape Dimensions (mm)
Reels Dimensions (mm)
A
178
B
50
C
D
E
13
14.4
8.4
W
8
P1
2
P2
4
P3
4
H
T
2.6
0.3
Notes: P1, P2 and P3 are same for all chip inductor series. Keeping the same dimensions for guide hole and pocket pitch (P1), pocket pitch (P2), guide hold pitch (P3) and tape width (8mm) for all series, enables the
packaging machine to maintain the same settings while changing models. The only difference between the series are the parts per reel which contributes to a different length of tapes/reel per model.
Pulse Jack
5
www.networking.pulseelectronics.com
WC711.C (7/19)
Electronics
很抱歉,暂时无法提供与“PE-1008CD471GTT”相匹配的价格&库存,您可以联系我们找货
免费人工找货