1A6

1A1 THRU 1A7 SILICON RECTIFIER VOLTAGE RANGE 1000 Volts CURRENT 1.0 Ampere FEATURES * * * * High reliability Low leakage Low forward voltage drop High current capability MECHANICAL DATA * * * * * Case: Molded plastic black body Epoxy: Device hasUL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.19 gram .787 (20.0) MIN. .025 (0.65) DIA. .021 (0.55) .126 (3.2) .106 (2.7) .102 (2.6) DIA. .091 (2.3) .787 (20.0) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 C unless otherwise noted) o SYMBOL Maximum Recurrent Peak Reverse Voltage VRRM 1A4 1000 Maximum RMS Voltage VRMS 700 Volts VDC 1000 Volts IO 1.0 Amps I FSM 25 Amps IT 2.59 AS RATINGS Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 25 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) 1A1 1A2 1A3 2 Typical Current Squared Time Typical Junction Capacitance (Note) Typical Thermal Resistance Operating and Storage Temperature Range CJ 15 R QJA 60 T J , T STG -55 to + 150 1A5 1A6 1A7 UNITS Volts 2 pF 0 C/ W 0 C ELECTRICAL CHARACTERISTICS (At TA = 25 C unless otherwise noted) o CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0A DC o @T A = 25 C Maximum DC Reverse Current o at Rated DC Blocking Voltage @T A = 150 C Maximum Full Load Reverse Current Full Cycle Average o .375” (9.5mm) lead length at T L = 75 C NOTES : 1.Measured at 1 MH Z and applied reverse voltage of 4.0 volts SYMBOL VF IR 1A1 1A2 1A3 1A4 1.0 1.0 2.0 100 1A5 1A6 1A7 UNITS Volts uAmps mAmps uAmps 2019-02 REV:E FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE .8 .6 .4 Single Phase Half Wave 60Hz Resistive or Inductive Load .2 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE, ( ) FIG. 3 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 8.3ms Single Half Sine-Wave (JEDED Method) 40 30 20 10 FIG. 2 - MAXIMUM INSTANTANEOUS FORWARD CHARACTERISTICS 20 10 4 2 1.0 .4 .2 .1 TJ = 25 Pulse Width=300uS 1% Duty Cycle .04 .02 .01 .6 .8 1.0 1.2 1.4 1.5 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 4 - MAXIMUM REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, (uA) 0 PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, (A) 1.0 10 Ta = 25 1.0 0.1 .01 0 1 2 4 6 8 10 20 40 6080100 NUMBER OF CYCLES AT 60Hz JUNCTION CAPACITANCE, (pF) AVERAGE FORWARD CURRENT, (A) RATING AND CHARACTERISTIC CURVES ( 1A1 THRU 1A7 ) 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG. 5 - TYPICAL JUNCTION CAPACITANCE 200 100 60 40 TJ = 25 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, ( V ) RECTRON AXIAL LEAD TAPING SPECIFICATIONS FOR RECTIFIERS Axial lead devices are packed in accordance with EIA standard RS-296-D and specifications given below. COMPNENT OUTLINE COMPONENT PITCH A 0.5mm (.020") T-1 R-1 A-405 A-405 DO-41 DO-41 DO-15 R-3 DO-201AD R-6 INNER TAPE PITCH B 0.5mm (.020") 1.5mm (.059") 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 10.0mm 10.0mm 26.0mm 26.0mm 26.0mm 52.4mm 26.0mm 52.4mm 52.4mm 52.4mm 52.4mm 52.4mm O Z 90 5 CUMULATIVE PITCH TOLERANCE 2.0mm/20pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch O DO A E W L1 D1 B L2 D T E Fig.: Configuration of AXIAL LEAD TAPING ITEM Component alignment Tape width Exposed adhesive Body eccentricity Reel outside diameter Reel inner diameter Feed hole diameter Reel width Notes : SYMBOL Z T E IL1-L2I D D1 DO W SPECIFICATIONS (mm) 1.2 Max. 6.0 0.4 0.8 Max. 1.0 Max. 330.0 85.7 0.3 30.5 0.4 79.0 1.0 1.Each component lead shall be sandwiched between tapes for a minimum of 3.2mm (0.126"). 2.The reel width "W" for 26mm taping is 50.0 1.0mm (1.97" 0.040"). SPECIFICATIONS (inch) 0.047 Max. 0.236 0.016 0.032 Max. 0.039 Max. 13.0 3.374 0.012 1.201 0.016 3.110 0.039 RADIAL-TAPING SPECIFICATIONS FOR RECTIFIERS-I TAPING P h A D F K2 d K1 B K3 H K4 L A1 W2 A2 W1 W0 W T P1 P0 D0 t Fig.: Configuration of I-TAPING ITEM Lead-wire clinch heigth Kinker heigth Kinker position Lead kinker length Component kinker spacing Adhesive tape position Body diameter Body length Lead-wire diameter Component pitch Feed hole pitch Component lead spacing Deflection Tape width Hole-down tape width Hole position Length from seating plane Feed hole diameter Totai tape thickness Cut out length Leed protrusion Center of seating plane location Adhesive tape position Lead bend Notes : SYMBOL SPECIFICATIONS(mm) SPECIFICATIONS(inch) A2 K1 K2 K3 K4 A1 D A d P P0 F h W W0 W1 H D0 t L T P1 W2 B 15.5 0.2 5.0 1.0 3.0 1.0 3.0 1.0 2.5 1.0 6.0 Min. 2.5 0.2 3.1 0.3 0.6 0.1 12.7 1.0 12.7 1.0 5.0 0.8 0.0 2.0 18.0+1.0/-0.5 12.5 Min. 9.0+0.7/-0.5 20.0 0.5 4.0 0.3 0.7 0.2 11.0 Max. 2.0 Max. 6.35 0.7 3.0 Max. 1.0 Max. 0.610 0.008 0.197 0.039 0.118 0.039 0.118 0.039 0.098 0.039 0.236 Min. 0.098 0.008 0.122 0.012 0.024 0.004 0.500 0.039 0.500 0.039 0.197 0.031 0.0 0.079 0.709+0.039/-0.020 0.492 Min. 0.354+0.028/-0.020 0.787 0.020 0.157 0.012 0.028 0.008 0.433 Max. 0.079 Mix. 0.250 0.028 0.118 Max. 0.039 Max. 1.Devices are pecked in accordance with EIA standard RS-468and specifications listed above. Available only for R-1 product utilizing 0.6mm diameter leads. 2.Maximum cumulative pitchtolerance : 1.0mm/20pitch. 3.Standard packing code is "l" RADIAL-TAPING SPECIFICATIONS FOR RECTIFIERS-J TAPING P h A D F d B H W2 L W1 W0 W T P1 P0 D0 t Fig.: Configuration of J-TAPING ITEM Body diameter Body height Lead-wire diameter Component pitch Feed hole pitch Component lead spacing Deflection SYMBOL D A d P PO F h SPECIFICATIONS(mm) 2.5 0.2 3.1 0.3 0.6 0.1 12.7 1.0 SPECIFICATIONS(inch) 0.098 0.008 0.122 0.012 0.024 0.004 0.500 0.039 12.7 1.0 5.0 0.8 0.500 0.039 0.197 0.032 0.0 2.0 0.000 0.079 Tape width Hold-down tape width W WO 18.0+1.0/-0.5 12.5 Min. 0.709+0.039/-0.020 0.492 Min. Hold-position Length from seating plane Feed hole diameter Overall tape thickness Cut out length W1 H DO t L 9.0+0.7/-0.50 20.0 0.5 4.0 0.3 0.7 0.2 11.0 Max. 0.354+0.028/-0.020 0.787 0.020 0.157 0.012 0.028 0.008 0.433 Max. Lead protrusion Center of seating plane location Adhesive tape border Lead bend T P1 W2 B 1.0 Max. 6.35 0.7 30 Max. 1.0 Max. 0.039 Max. 0.250 0.028 1.181 Max. 0.039 Max. Notes : 1.Devices are packed in accordance with EIA standard RS-468 and specification given above. Available only for R-1 product utilizing 0.6mm diameter leads. 2.Maximum cumulative pitch tolerance:1.0mm/20pitch. 3.Standard packing code is "J". 1. Internal Circuit Anode Cathode 2. Marking on the body Cathode Band Plant - code Part No. AH V X X Month - code H---for all Voltage rang Year - code PACKAGING OF DIODE AND BRIDGE RECTIFIERS REEL PACK PACKAGE PACKING EA PER EA PER COMPONENT TAPE SPACE REEL DIA CARTON SIZE EA PER GROSS SPACE INNER REEL CARTON WEIGHT(Kg) CODE (mm) (mm) (mm) (mm) BOX R-1 -T 5,000 5,000 5.0 330 52 355*350*335 20,000 7.37 AMMO PACK PACKAGE PACKING CODE REEL ( EA ) COMPONENT TAPE SPACE SPACE(mm) (mm) R-1 -F 3,000 5.0 R-1 -E 3,000 R-1 -J R-1 -I BOX SIZE (mm) CARTON SIZE(mm) CARTON ( EA ) GROSS WEIGHT (Kg) 52 255*73*100 400*268*225 30,000 8.5 5.0 26 256*48*94 365*270*217 42,000 8.35 3,000 12.7 --- 325*170*40 355*350*335 42,000 13.93 2,000 12.7 --- 325*170*40 355*350*335 28,000 9.69 BULK PACK PACKAGE PACKING CODE R-1 -B EA PER BOX 1000 INNER BOX SIZE CARTON SIZE (mm) (mm) 192*75*21 415*220*255 EA PER CARTON 50,000 GROSS WEIGHT(Kg) 11.74 DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.