BR1505

VOLTAGE RANGE 50 to 1000 Volts CURRENT 15 Amperes SINGLE-PHASE SILICON BRIDGE RECTIFIER BR1505 T HRU BR1510 FEATURES * * * * S uperior thermal desing 3 00 amperes surge rating 1 /4" universal faston terminal H ole thru for #8 screw MECHANICAL DATA * Epoxy : Device has UL flammability classification 94V-0 * UL listed the recongnized component director, file #94233 D co is ed inu nt BR-15 DISCONTINUED- "This series is replaced by the MP15 series that meets to the same fit and function parameters. The MP15 series is preferred for PCB assembly.＂ MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. BR-15W MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TC = 55oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 2) Operating and Storage Te mperature Range E LECTRICAL CHARACTERISTICS (@TA=25 C unless otherwise noted) O SYMBOL VRRM VRMS VDC IO IFSM RqJC RqJA T J, TSTG BR1505 50 35 50 BR151 100 70 100 BR152 200 140 200 BR154 400 280 400 15.0 300 5 22 -55 to + 150 BR156 600 420 600 BR158 800 560 800 BR1510 1000 700 1000 UNITS Volts Volts Volts Amps Amps O C/W 0 C CHARACTERISTICS Maximum Instantaneous Forward Voltage at 7.5A DC Maximum DC Reverse Current at Rated DC Blocking Voltage NOTES : @TA = 25oC @TC = 100oC SYMBOL VF IR BR1505 BR151 BR152 BR154 1.1 5.0 500 BR156 BR158 BR1510 UNITS Volts uAmps 2007-5 1. Suffix "W" for wire type. 2. Typical Thermal Resistance: Heat-sink case mounted. 3. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. RATING AND CHARACTERISTICS CURVES ( BR1505 THRU BR1510 ) INSTANTANEOUS FORWARD CURRENT, (uA) 18 AVERAGE FORWARD CURRENT, (A) 15 12 9 6 3 0 Single Phase Half Wave 60Hz Inductive or Resistive Load 0.375" (9.5mm) Lead Length 1000 TA = 100 OC 100 T A = 7 5 OC 10 T A = 2 5 OC 1 0 50 100 O 150 0.1 0 20 40 60 80 100 120 140 CASE TEMPERATURE, ( C) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS REVERSE CURRENT, (A) PEAK FORWARD SURGE CURRENT, (A) 500 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 300 250 200 150 100 50 0 1 FIG.2 TYPICAL REVERSE CHARACTERISTICS 8.3mS Single Half Sine-Wave JEDEC Method 100 10 T J = 2 5 OC Pulse width=300mS 1% Duty Cycle 1 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 2 5 10 20 50 100 INSTANTANEOUS FORWARD VOLTAGE, (V) NUMBER OF CYCLES AT 60Hz FIG.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS .452 MAX. (11.5) .480 (12.2) .425 (10.8) 1.181 (30.0) 1.102 (28.0) .673 (17.1) .633 (16.1) FIG.4 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT .452 MAX. (11.5) .042 (1.1) DIA. .080 (2.0) TYP. 1.181 (30.0) 1.102 (28.0) .591 MAX. (15.0) HOLE FOR NO. 8 SCREW HOLE FOR NO. 8 SCREW 1.181 (30.0) 1.102 (28.0) .468 (11.9) .429 (10.9) AC .732 (18.6) .692 (17.6) AC 1.181 (30.0) 1.102 (28.0) .673 (17.1) .633 (16.1) AC .732 (18.6) .692 (17.6) AC .582 (14.8) .543 (13.8) .033 x .250 (0.8 x 6.4) .732 (18.6) .692 (17.6) BR-15 BR-15W DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.