RL157

RL151 THRU RL157 SILICON RECTIFIER VOLTAGE RANGE 1000 Volts CURRENT 1.5 Ampere FEATURES * * * * Low cost Low leakage Low forward voltage drop High current capability MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.40 gram .035 (0.88) 1.0 (25.4) .027 (0.68) DIA. MIN. .300 (7.6) .230 (5.8) .140 (3.6) .104 (2.6) DIA. 1.0 (25.4) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS MIN. o Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 C unless otherwise noted) o SYMBOL RATINGS RL151 RL152 RL153 RL154 RL155 RL156 RL157 UNITS Maximum Recurrent Peak Reverse Voltage VRRM 1000 Maximum RMS Voltage VRMS 700 Volts VDC 1000 Volts IO 1.5 Amps I FSM 60 Amps 14.94 A2/Sec Maximum DC Blocking Voltage Maximum Average Forward Rectified Current o at T A = 75 C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) 2 Typical Current Squarad Time I t Typical Junction Capacitance (Note) Typical Thermal Resistance Operating and Storage Temperature Range CJ 20 RQJA T J , T STG 50 -55 to + 150 Volts pF 0 C/ W 0 C ELECTRICAL CHARACTERISTICS (At TA = 25 C unless otherwise noted) o CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.5A DC o Maximum DC Reverse Current @T A = 25 C o at Rated DC Blocking Voltage @T A = 150 C Maximum Full Load Reverse Current Average, Full Cycle .375” (9.5mm) lead length at TL = 75oC NOTES : 1. Measured at 1 MHZ and applied reverse voltage of 4.0 volts SYMBOL VF IR RL151 RL152 RL153 RL154 1.0 1.0 2.0 30 RL155 RL156 RL157 UNITS Volts uAmps mAmps uAmps 2021-06 REV:F RATING AND CHARACTERISTIC CURVES ( RL151 THRU RL157 ) FIG. 2 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1.5 INSTANTANEOUS FORWARD CURRENT, (A) AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 1.2 .9 .6 Single Phase Half Wave 60Hz Inductive or Resistive Load .3 4 2 1.0 .4 .2 .1 TJ = 25 Pulse Width=300uS 1% Duty Cycle .04 .02 .01 .6 0 0 20 10 25 50 75 100 125 150 175 AMBIENT TEMPERATURE, ( ) .8 1.0 1.2 1.4 1.5 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 3 - MAXIMUM NON-REPETITIVE FORWARD INSTANTANEOUS REVERSE CURRENT, (uA) SURGE CURRENT 8.3ms Single Half Sine-Wave (JEDED Method) 60 45 30 15 5 1 2 4 6 8 10 20 40 6080100 NUMBER OF CYCLES AT 60Hz 10000 TA = 150 1000 1.0 TA = 25 .1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG. 5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, (pF) PEAK FORWARD SURGE CURRENT, (A) 75 FIG. 4 - MAXIMUM REVERSE CHARACTERISTICS 200 100 60 40 20 10 6 4 TJ = 25 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, ( V ) RECTRON AXIAL LEAD TAPING SPECIFICATIONS FOR RECTIFIERS Axial lead devices are packed in accordance with EIA standard RS-296-D and specifications given below. COMPNENT OUTLINE COMPONENT PITCH A 0.5mm (.020") T-1 R-1 5.0mm 5.0mm INNER TAPE PITCH B 0.5mm (.020") 1.5mm (.059") CUMULATIVE PITCH TOLERANCE 2.0mm/20pitch 2.0mm/20pitch 26.0mm 26.0mm R-1 5.0mm A-405 A-405 DO-41 DO-41 DO-15 R-3 DO-201AD 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 10.0mm 52.4mm 2.0mm/20pitch R-6 10.0mm 52.4mm 2.0mm/10pitch 1.5KE 10.0mm 52.4mm 2.0mm/10pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 26.0mm 52.4mm 26.0mm 52.4mm 52.4mm 52.4mm 52.4mm Note: -E for 26mm inner tape pitch -F & -T for 52mm inner tape pitch Z O O 90 5 DO A E W L1 D1 B L2 D T E Fig.: Configuration of AXIAL LEAD TAPING ITEM Component alignment Tape width Exposed adhesive Body eccentricity Reel outside diameter Reel inner diameter Feed hole diameter Reel width Notes : SYMBOL Z T E IL1-L2I D D1 DO W SPECIFICATIONS (mm) 1.2 Max. 6.0 0.4 0.8 Max. 1.0 Max. 330.0 85.7 0.3 30.5 0.4 79.0 1.0 1.Each component lead shall be sandwiched between tapes for a minimum of 3.2mm (0.126"). 2.The reel width "W" for 26mm taping is 50.0 1.0mm (1.97" 0.040"). SPECIFICATIONS (inch) 0.048 Max. 0.236 0.016 0.032 Max. 0.040 Max. 13.0 3.375 0.012 1.201 0.016 3.110 0.040 2002-12 PACKAGING OF DIODE AND BRIDGE RECTIFIERS BULK PACK PACKAGE PACKING CODE DO-15 -B EA PER BOX INNER BOX SIZE (mm) 500 194*84*21 CARTON SIZE EA PER CARTON (mm) 415*220*255 25,000 GROSS WEIGHT(Kg) 12.74 REEL PACK PACKAGE DO-15 PACKING EA PER EA PER COMPONENT TAPE SPACE REEL DIA CARTON SIZE EA PER GROSS SPACE INNER REEL CARTON WEIGHT(Kg) CODE (mm) (mm) (mm) (mm) BOX -T 4,000 4,000 5.0 52 330 355*350*335 16,000 10.05 AMMO PACK PACKAGE PACKING CODE REEL ( EA ) DO-15 -F 1,500 COMPONENT TAPE SPACE SPACE(mm) (mm) 5.0 52 BOX SIZE (mm) CARTON SIZE(mm) 255*73*100 400*268*225 CARTON ( EA ) 15,000 GROSS WEIGHT (Kg) 8.8 RECTRON Attachment information about RL15X 1. Internal Circuit Anode Cathode 2. Marking on the body Cathode Band Plant - code Year - code Rectron Logo Part No. V X X R L 1 5 H Month - code (M:0~9,O,N,D) H---for all Voltage rang 3. The net weight 380mg / pcs 4. Taping packaging specification 4.1All polarized components must be oriented in one direction. 4.2For diode, at least one side of the cathode lead tape should be red, and anode lead tape should be white. 4.3A minimum 300 mm (12”) leader shall be provided at each end of the reel. 4.4Staples shall not be used for splicing. Splice length shall be 4.0 inches minimum and shall not be misaligned more than 0.8mm. RECTRON Attachment information about RL15X 5. Items marked on the reel box and carton 5.1 On the reel (for –T) CUSTOMER TYPE QUANTITY LOT NO. Q.A. REMARK 5.2 On the box (for –E & -F) TYPE QUANTITY LOT NO. Q.A. 5.3 On the carton CUSTOMER TYPE QUANTITY LOT NO. REMARK DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.