0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
728980J8

728980J8

  • 厂商:

    RENESAS(瑞萨)

  • 封装:

    LCC44

  • 描述:

    IC MULTIPLEXER 1 X 8:8 44PLCC

  • 数据手册
  • 价格&库存
728980J8 数据手册
TIME SLOT INTERCHANGE DIGITAL SWITCH 256 x 256 FEATURES: • • • • • • • • • IDT728980 and output channels. Those 256 channels are divided into 8 serial inputs and outputs, each of which consists of 32 channels (64 Kbit/s per channel) to form a multiplexed 2.048 Mb/s stream. 256 x 256 channel non-blocking switch Serial Telecom Bus Compatible (ST-BUS®) 8 RX inputs—32 channels at 64 Kbit/s per serial line 8 TX output—32 channels at 64 Kbit/s per serial line Three-state serial outputs Microprocessor Interface (8-bit data bus) 5V Power Supply Available in 44-pin Plastic Leaded Chip Carrier (PLCC) Operating Temperature Range -40°°C to +85°°C FUNCTIONAL DESCRIPTION A functional block diagram of the IDT728980 device is shown on below. The serial ST-BUS® streams operate continuously at 2.048 Mb/s and are arranged in 125μs wide frames each containing 32, 8-bit channels. Eight input (RX0-7) and eight output (TX0-7) serial streams are provided in the IDT728980 device allowing a complete 256 x 256 channel non-blocking switch matrix to be constructed. The serial interface clock (C4i) for the device is 4.096 MHz. The received serial data is internally converted to a parallel format by the on chip serial-to-parallel converters and stored sequentially in a 256-position Data Memory. By using an internal counter that is reset by the input 8 KHz frame pulse, F0i, the incoming serial data streams can be framed and sequentially addressed. DESCRIPTION: The IDT728980 is a ST-BUS® compatible digital switch controlled by a microprocessor. The IDT728980 can handle as many as 256, 64 Kbit/s input FUNCTIONAL BLOCK DIAGRAM C4i F0i VCC Timing Unit RX0 TX0 Output MUX RX1 RX2 RX3 RX4 TX1 TX2 Receive Serial Data Streams Transmit Serial Data Streams Data Memory RX5 Control Register RX6 RX7 ODE GND Connection Memory TX3 TX4 TX5 TX6 Microprocessor Interface TX7 5706 drw01 DS CS R/W A0/ DTA D0/ A5 D7 CCO MARCH 2017 IDT and the IDT logo are registered trademarks of Integrated Device Technology, Inc. 1 ©2017 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. DSC-5706/2 IDT728980 Time Slot Interchange Digital Switch 256 x 256 COMMERCIAL TEMPERATURE RANGE TX0 TX1 TX2 DNC(1) 42 41 40 ODE 2 43 RX0 DTA 3 CCO RX1 4 11 35 TX7 VCC 12 34 GND F0i 13 33 D0 C4i 14 32 D1 A0 15 31 D2 A1 16 30 D3 A2 17 29 D4 DNC(1) D5 D6 D7 CS R/W DS A5 A4 A3 28 RX7 26 TX6 27 TX5 36 25 37 10 24 9 RX6 22 RX5 23 TX4 21 TX3 38 20 39 8 19 7 RX4 18 RX3 DNC(1) NOTE: 1. DNC - Do Not Connect. 44 RX2 5 1 DNC(1) INDEX 6 PIN CONFIGURATION 5706 drw02 PLCC: 0.05in. pitch, 0.65in. x 0.65in. (J44, order code: J) TOP VIEW PIN DESCRIPTIONS SYMBOL GND VCC DTA RX0-7 F0i C4i A0-A5 DS R/W NAME Ground. VCC Data Acknowledgment (Open Drain) RX Input 0 to 7 Frame Pulse Clock Address 0 to 5 Data Strobe I/O O I I I I I Read/Write Chip Select Data Bus 0 to 7 I I I/O O ODE TX Outputs 0 to 7 (Three-state Outputs) Output Drive Enable CCO Control Channel Output O CS D0-D7 TX0-7 I DESCRIPTION Ground Rail. +5.0 Volt Power Supply. This active LOW output indicates that a data bus transfer is complete. A pull-up resistor is required at this output. Serial data input streams. These streams have 32 channels at data rates of 2.048 Mb/s. This input identifies frame synchronization signals formatted to ST-BUS® specifications. 4.096 MHz serial clock for shifting data in and out of the data streams. These lines provide the address to IDT728980 internal registers. This is the input for the active HIGH data strobe on the microprocessor interface. This input operates with CS to enable the internal read and write generation. This input controls the direction of the data bus lines (D0-D7) during a microprocessor access. Active LOW input enabling a microprocessor read or write of control register or internal memories. These pins provide microprocessor access to data in the internal control register. Connection Memory HIGH, Connection Memory LOW and data memory. Serial data output streams. These streams are composed of 32, 64 Kbit/s channels at data rates of 2.048 Mb/s. This is an output enable for the TX0-7 serial outputs. If this input is LOW, TX0-7 are high-impedance. If this is HIGH, each channel may still be put into high-impedance by software control. This output is a 2.048 Mb/s line which contains 256 bits per frame. The level of each bit is controlled by the contents of the CCO bit in the Connection Memory HIGH locations. 2 IDT728980 Time Slot Interchange Digital Switch 256 x 256 COMMERCIAL TEMPERATURE RANGE FUNCTIONAL DESCRIPTION (Cont'd) device varies according to the combination of input and output streams and the movement within the stream from channel to channel. Data received on an input stream must first be stored in Data Memory before it is sent out. As information enters the IDT728980 it must first pass through an internal serial-to-parallel converter. Likewise, before data leaves the device, it must pass through the internal parallel-to-serial converter. This data preparation has an effect on the channel positioning in the frame immediately following the incoming frame-mainly, data cannot leave in the same time slot, or in the time slot immediately following. Therefore, information that is to be output in the same channel position as the information is input, relative to the frame pulse, will be output in the following frame. As well, information switched to the channel immediately following the input channel will not be output in the time slot immediately following, but in the next timeslot allocated to the output channel, one frame later. Whether information can be output during a following timeslot after the information entered the IDT728980 depends on which RX stream the channel information enters on and which TX stream the information leaves on. This is caused by the order in which input stream information is placed into Data Memory and the order in which stream information is queued for output. Table 1 shows the allowable input/output stream combinations for the minimum 2 channel delay. Data to be output on the serial streams may come from two sources: Data Memory or Connection Memory. The Connection Memory is 16 bits wide and is split into two 8-bit blocks—Connection Memory HIGH and Connection Memory LOW. Each location in Connection Memory is associated with a particular channel in the output stream so as to provide a one-to-one correspondence between the two memories. This correspondence allows for per channel control for each TX output stream. In Processor Mode, data output on the TX stream is taken from the Connect Memory Low and originates from the microprocessor (Figure 2). Where as in Connection Mode (Figure 1), data is read from Data Memory using the address in Connection Memory. Data destined for a particular channel on the serial output stream is read during the previous channel time slot to allow time for memory access and internal parallelto-serial conversion. CONNECTION MODE In Connection Mode, the addresses of input source for all output channels are stored in the Connect Memory Low. The Connect Memory Low locations are mapped to corresponding 8-bit x 32-channel output. The contents of the Data Memory at the selected address are then transferred to the parallel-toserial converters. By having the output channel to specify the input channel through the connect memory, input channels can be broadcast to several output channels. SOFTWARE CONTROL If the A5 address line input is LOW then the IDT728980 Internal Control Register is addressed. If A5 input line is high, then the remaining address input lines are used to select the 32 possible channels per input or output stream. The address input lines and the Stream Address bits (STA) of the Control register give the user the capability of selecting all positions of IDT728980 Data and Connection memories. The IDT728980 memory mapping is illustrated in Table 2 and Figure 3. The data in the control register (Table 3) consists of Memory Select and Stream Address bits, Split Memory and Processor Mode bits. In Split Memory mode (Bit 7 of the Control register) reads are from the Data Memory and writes are to the Connect Memory as specified by the Memory Select Bits (Bits 4 and 3 of the Control Register). The Memory Select bits allow the Connect Memory High or LOW or the Data Memory to be chosen, and the Stream Address bits define internal memory subsections corresponding to input or output streams. The Processor Enable bit (bit 6) places EVERY output channel on every output stream in Processor Mode; i.e., the contents of the Connect Memory LOW (CML, see Table 5) are output on the TX output streams once every frame unless the ODE input pin is LOW. If PE bit is HIGH, then the IDT728980 behaves as if bits 2 (Channel Source) and 0 (Output Enable) of every Connect Memory High (CMH) locations were set to HIGH, regardless of the actual value. If PE is LOW, then bit 2 and 0 of each Connect Memory High location operates normally. In this case, if bit 2 of the CMH is HIGH, the associated TX output channel is in Processor Mode. If bit 2 of the CMH is LOW, then the contents of the CML define the source information (stream and channel) of the time slot that is to be switched to an output. PROCESSOR MODE In Processor Mode the CPU writes data to specific Connect Memory Low locations which are to be output on the TX streams. The contents of the Connect Memory Low are transferred to the parallel-to-serial converter one channel before it is to be output and are transmitted each frame to the output until it is changed by the CPU. CONTROL The Connect Memory High bits (Table 4) control the per-channel functions available in the IDT728980. Output channels are selected into specific modes such as: Processor Mode or Connection mode and Output Drivers Enabled or in three-state condition. There is also one bit to control the state of the CCO output pin. OUTPUT DRIVE ENABLE (ODE) The ODE pin is the master output control pin. If the ODE input is held LOW all TDM outputs will be placed in high impedance regardless Connect Memory High programming. However, if ODE is HIGH, the contents of Connect Memory High control the output state on a per-channel basis. DELAY THROUGH THE IDT728980 The transfer of information from the input serial streams to the output serial streams results in a delay through the device. The delay through the IDT728980 RX Receive Serial Data Streams Data Memory Connection Memory Transmit Serial Data Streams Receive Serial Data Streams TX Data Memory Connection Memory Transmit Serial Data Streams TX 5706 drw06 Microprocessor 5706 drw05 Figure 2. Processor Mode Figure 1. Connection Mode 3 IDT728980 Time Slot Interchange Digital Switch 256 x 256 COMMERCIAL TEMPERATURE RANGE If the ODE input pin is LOW, then all the serial outputs are high-impedance. If ODE is HIGH, then bit 0 (Output Enable) of the CMH location enables (if HIGH) or disables (if LOW) the output stream and channel. The contents of bit 1 (CCO) of each Connection Memory High Location (see Table 4) is output on CCO pin once every frame. The CCO pin is a 2.048 Mb/s output, which carries 256 bits. If CCO bit is set HIGH, the corresponding bit on CCO output is transmitted HIGH. If CCO is LOW, the corresponding bit on the CCO output is transmitted in LOW. The contents of the 256 CCO bits of the CMH are transmitted sequentially on to the CCO output pin and are synchronous to the TX streams. To allow for delay in any external control circuitry the contents of the CCO bit is output one channel before the corresponding channel on the TX streams. For example, the contents of CCO bit in position 0 (corresponding to TX0, CH0) is transmitted synchronously with the TX channel 31, bit 7. Bit 1's of CMH for channel 1 of stream 0-7 are output synchronously with TX channel 0 bits 7-0. Input Output Stream 0 1,2,3,4,5,6,7 1 2 3 4 5 6 7 3,4,5,6,7 5,6,7 7 1,2,3,4,5,6,7 3,4,5,6,7 5,6,7 7 INITIALIZATION OF THE IDT728980 On initialization or power up, the contents of the Connection Memory High can be in any state. This is a potentially hazardous condition when multiple TX outputs are tied together to form matrices. The ODE pin should be held low on power up to keep all outputs in the high impedance condition until the contents of the CMH are programmed. During the microprocessor initialization routine, the microprocessor should program the desired active paths through the matrices, and put all other channels into the high impedance state. Care should be taken that no two connected TX outputs drive the bus simultaneously. With the CMH setup, the microprocessor controlling the matrices can bring the ODE signal high to relinquish high impedance state control to the Connection Memory High bits outputs. A5 A4 A3 A2 A1 A0 LOCATION 0 1 1 X 0 0 X 0 0 X 0 0 X 0 0 X 0 1 00-1F 20 21 Control Register(1) Channel 0(2) Channel 1(2) • • • • • • • • • • • • • • • • • • • • • • • • 1 1 1 1 1 1 3F Channel 31(2) NOTES: 1. Writing to the Control Register is the only fast transaction. 2. Memory and stream are specified by the contents of the Control Register. Table 1. Input Stream to Output Stream Combinations that can Provide the Minimum 2-Channel Delay Control Register HEX ADDRESS CRb7 CRb6 The Control Register is only accessed when A5=0. All other address bits have no effect when A5=0. When A5 =1, only 32 bytes are randomly accessable via A0-A4 at any one instant. Which 32 bytes are accessed is determined by the state of CRb0 -CRb4. The 32 bytes correlate to 32 channel of one ST-BUS® stream. Table 2. Address Mapping CRb5 CRb4 0 1 1 CRb4 CRb3 CRb2 CRb1 CRb0 CRb3 1 0 1 Connection Memory High Connection Memory Low Data Memory Channel 0 Channel 0 Channel 0 Channel 0 Channel 0 Channel 0 Channel 0 Channel 0 Channel 1 Channel 1 Channel 1 Channel 1 Channel 1 Channel 1 Channel 1 Channel 1 100000 100001 Channel 2 Channel 2 Channel 2 Channel 2 Channel 2 Channel 2 Channel 2 Channel 2 100010 Channel 31 Channel 31 Channel 31 Channel 31 Channel 31 Channel 31 Channel 31 Channel 31 CRb2 0 0 0 0 1 1 1 1 CRb1 0 0 1 1 0 0 1 1 111111 External Address Bits CRb0 Stream 0 0 1 1 2 0 1 3 0 4 1 5 0 6 1 7 A5-A0 5706 drw07 Figure 3. Address Mapping 4 IDT728980 Time Slot Interchange Digital Switch 256 x 256 COMMERCIAL TEMPERATURE RANGE Mode Control Bits 7 Bit 6 (unused) Memory Select Bits 5 4 Name 3 Stream Address Bits 2 1 0 Description 7 SM (Split Memory) When 1, all subsequent reads are from the Data Memory and writes are to the Connection Memory LOW, except when the Control Register is accessed again. When 0, the Memory Select bits specify the memory for the operations. In either case, the Stream Address Bits select the subsection of the memory which is made available. 6 PE (Processor Mode) When 1, the contents of the Connection Memory LOW are output on the Serial Output streams except when the ODE pin is LOW. When 0, the Connection Memory bits for each channel determine what is output. 5 unused 4-3 MS1-MS0 (Memory Select Bits) 0-0 - Not to be used. 0-1 - Data Memory (read only from the microprocessor port) 1-0 - Connection Memory LOW 1-1 - Connection Memory is HIGH 2-0 STA2-0 (Stream Address Bits) The number expressed in binary notation on these bits refers to the input or output stream which corresponds to the subsection of memory made accessible for subsequent operations. Table 3. Control Register Configuration No Corresponding Memory - These bits give 0s if read 7 Bit 6 5 4 Name Per Channel Control Bits 3 2 1 0 Description 2 CS (Channel Source) When 1, the contents of the corresponding location in Connection Memory LOW are output on the location's channel and stream. When 0, the contents of the corresponding location in Connection Memory LOW act as an address for the Data Memory and determine the source of the connection to the location's channel and stream. 1 CCO (CCO Bit) This bit is output on the CCO pin one channel early. The CCO bit for stream 0 is output first. 0 OE (Output Enable) If the ODE pin is HIGH and bit 6 of the Control Register is 0, then this bit enables the output drive for the location's channel and stream. This allows individuals channels on individuals streams to be made high-impedance, allowing switching matrices to be constructed. A 1 enables the driver and a 0 disables it. Table 4. Connection Memory High Register Stream Address Bits 7 Bit 7-5(1) 6 Channel Address Bits 5 4 Name Stream Address Bits 4-0(1) Channel Address Bits 3 2 1 0 Description The number expressed in binary notation on these 3 bits are the number of the stream for the source of the connection. Bit 7 is the most significant bit, e.g., If bit 7 is 1, bit 6 is 0 and bit 5 is 0 then the source of the connection is a channel on RX4. The number expressed in binary notation on these 5 bits is the number of the channel which is the source of the connection (the stream where the channel lies is defined by bits 7, 6 and 5). Bit 4 is the most significant bit, e.g., if bit 4 is 1, bit 3 is 0, bit 2 is 0, bit 1 is 1 and bit 0 is 1, then the source of the connection is channel 19. NOTE: 1. If bit 2 of the corresponding Connection HIGH location is 1 or bit 6 of the Control Register is 1, then these entire 8 bits are output on the channel and stream associated with this location. Otherwise, the bits are used as indicated to define the source of the connection which is output on the channel and stream associated with this location. Table 5. Connection Memory Low Register 5 IDT728980 Time Slot Interchange Digital Switch 256 x 256 COMMERCIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS Symbol Parameter Min. Max. Unit VCC - GND -0.3 7 V Vi Voltage on Digital Inputs GND - 0.3 VCC +0.3 V VO Voltage on Digital Outputs GND - 0.3 VCC +0.3 V IO Current at Digital Outputs 40 mA TS Storage Temperature +150 °C PD Package Power Dissapation 2 W -65 RECOMMENDED OPERATING CONDITIONS (1) Symbol Parameter Typ.(1) Max. Unit 4.75 ⎯ 5.25 V 0 ⎯ VCC V -40 ⎯ +85 °C Min. VCC Positive Supply VI Input Voltage TOP Operating Temperature Commercial NOTE: 1. Typical figures are at 25°C and are for design aid only; not guaranteed and not subject to production testing. NOTE: 1. Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. DC ELECTRICAL CHARACTERISTICS Symbol Parameter Min. Typ.(1) Max. Units Test Conditions 10 mA Outputs Unloaded ICC Supply Current ⎯ 7 VIH Input High Voltage 2.0 ⎯ ⎯ V VIL Input Low Voltage ⎯ ⎯ 0.8 V IIL Input Leakage ⎯ ⎯ 5 μA CI Input Capacitance ⎯ 8 ⎯ pF VOH Output High Voltage 2.4 ⎯ ⎯ V IOH = 10mA VI between GND and VCC IOH Output High Current 10 15 ⎯ mA Sourcing. VOH = 2.4V VOL Output Low Voltage ⎯ ⎯ 0.4 V IOL = 5mA IOL Output Low Current 5 10 ⎯ mA Sinking. VOL = 0.4V IOZ High Impedance Leakage ⎯ ⎯ 5 μA VO between GND and VCC CO Output Pin Capacitance ⎯ 8 ⎯ pF NOTE: 1. Typical figures are at 25°C and are for design aid only; not guaranteed and not subject to production testing. Test Point VCC S1 is open circuit except when testing output levels or high impedance states. S2 S2 is switched to VCC or GND when testing output levels or high impedance states. RL Output Pin S1 CL GND GND 5706 drw08 Figure 4. Output Load 6 IDT728980 Time Slot Interchange Digital Switch 256 x 256 COMMERCIAL TEMPERATURE RANGE AC ELECTRICAL CHARACTERISTICS (1) ⎯ CLOCK TIMING Typ.(2) Symbol Characteristics Min. tCLK Clock Period(3) Max. Unit 220 244 300 ns tCH Clock Width High 95 122 150 ns tCL Clock Width Low 110 122 150 ns tCTT Clock Transition Time ⎯ 20 ⎯ ns tFPS Frame Pulse Setup Time 20 ⎯ 200 ns tFPH Frame Pulse Hold Time 0.020 ⎯ 50 μs tFPW Frame Pulse Width ⎯ 244 ⎯ ns NOTE: 1. Timing is over recommended temperature and power supply voltages. 2. Typical figures are at 25°C and are for design aid only; not guaranteed and not subject to production testing. 3. Contents of Connection Memory are not lost if the clock stops, however, TX outputs go into the high impedance state. C4i F0i Channel 31 Bit 0 Bit Cells Channel 0 Bit 7 5706 drw09 Figure 5. Frame Alignment tCLK tCTT tCTT tCHL tCL t CH C4i (( )) tFPH tFPS tFPH tFPS tFPW F0i 5706 drw10 Figure 6. Clock Timing 7 IDT728980 Time Slot Interchange Digital Switch 256 x 256 COMMERCIAL TEMPERATURE RANGE AC ELECTRICAL CHARACTERISTICS Symbol Characteristics (1) ⎯ SERIAL STREAM TIMING Min. Typ.(2) Max. Unit Test Conditions tTAZ TX0-7 Delay - Active to High Z 20 30 60 ns RL = 1KΩ(3), CL = 150pF tTZA TX0-7 Delay - High Z to Active 25 45 70 ns CL = 150pF tTAA TX0-7 Delay - Active to Active 30 45 70 ns CL = 150pF tTOH TX0-7 Hold Time 25 45 ⎯ ns CL = 150pF tOED Output Driver Enable Delay ⎯ 40 70 ns RL = 1KΩ(3), CL = 150pF tXCH External Control Hold Time 0 10 ⎯ ns CL = 150pF tXCD External Control Delay ⎯ 20 40 ns CL = 150pF tSIS Serial Input Setup Time ⎯ -40 -20 ns tSIH Serial Input Hold Time 90 ⎯ ⎯ ns NOTE: 1. Timing is over recommended temperature and power supply voltages. 2. Typical figures are at 25°C and are for design aid only; not guaranteed and not subject to production testing. 3. High Impedance is measured by pulling to the appropriate rail with RL, with timing corrected to cancel time taken to discharge CL. Bit Cell Boundary ODE C4i tOED tOED tTAZ tTOH TX0-7 5706 drw12 TX0-7 Figure 8. Output Driver Enable tTZA TX0-7 tTAA tTOH Bit Cell Boundaries TX0-7 C4i t XCD t XCH tSIS CCO tSIH RX0-7 5706 drw11 5706 drw13 Figure 7. Serial Outputs and External Control Figure 9. Serial Inputs 8 IDT728980 Time Slot Interchange Digital Switch 256 x 256 COMMERCIAL TEMPERATURE RANGE AC ELECTRICAL CHARACTERISTICS Symbol Characteristics (1) ⎯ PROCESSOR BUS Min. Typ.(2) Max. Unit tCSS Chip Select Setup Time 10 0 ⎯ ns Test Conditions tRWS Read/Write Setup Time 10 ⎯ ⎯ ns tADS Address Setup Time 10 ⎯ ⎯ ns tAKD Acknowledgment Delay Fast ⎯ 30 60 ns CL = 150pF tAKD Acknowledgment Delay Slow 2.7 ⎯ 7.2 cycles C4i cycles(4) tFWS Fast Write Data Setup Time 20 ⎯ ⎯ ns tSWD Slow Write Data Delay ⎯ 2.0 1.7 cycles C4i cycles tRDS Read Data Setup Time ⎯ ⎯ 0.5 cycles C4i cycles, CL = 150pF tDHT Data Hold Time Read 20 ⎯ ⎯ ns RL = 1KΩ(3), CL = 150pF tDHT Data Hold Time Write 20 10 ⎯ ns tRDZ Read Data to High Impedance ⎯ 30 60 ns tCSH Chip Select Hold Time 0 ⎯ ⎯ ns tRWH Read/Write Hold Time 0 ⎯ ⎯ ns tADH Address Hold Time 0 ⎯ ⎯ ns tAKH Acknowledgment Hold Time 10 20 40 ns RL = 1KΩ(3), CL = 150pF RL = 1KΩ(3), CL = 150pF NOTE: 1. Timing is over recommended temperature and power supply voltages. 2. Typical figures are at 25°C and are for design aid only; not guaranteed and not subject to production testing. 3. High Impedance is measured by pulling to the appropriate rail with RL, with timing corrected to cancel time taken to discharge CL. 4. Processor accesses are dependent on the C4i clock, and so some things are expressed as multiples of the C4i. DS tCSS t CSH tRWS tRWH tADS t ADH CS R/W A5-A0 tAKD tAKH DTA t RDS tSWD tRDZ tFWS tDHT D7-D0 5706 drw14 Figure 10. Processor Bus 9 ORDERING INFORMATION XXXXXX Device Type XX Package X X Process/ Temperature Range X Blank 8 Tube Tape and Reel BLANK Commercial (-40°C to +85°C) G Green J Plastic Leaded Chip Carrier (PLCC, J44) 728980 256 x 256 ⎯ Time Slot Interchange Digital Switch 5610 drw25 DATASHEET DOCUMENT HISTORY 05/23/2000 08/18/2000 01/24/2001 03/13/2017 pgs. pgs. pgs. pgs. 1, 2, and 10. 1, 2, and 10. 1 and 6. 1, 2, and 10. CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 10 for Tech Support: 408-360-1753 email: FIFOhelp@idt.com IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.
728980J8 价格&库存

很抱歉,暂时无法提供与“728980J8”相匹配的价格&库存,您可以联系我们找货

免费人工找货