ADC1413S125HN/C1:5

ADC1413S series Single 14-bit ADC; 65 Msps, 80 Msps, 105 Msps or 125 Msps; serial JESD204A interface Rev. 03 — 2 July 2012 Product data sheet 1. General description The ADC1413S is a single channel 14-bit Analog-to-Digital Converter (ADC) optimized for high dynamic performance and low power at sample rates up to 125 Msps. Pipelined architecture and output error correction ensure the ADC1413S is accurate enough to guarantee zero missing codes over the entire operating range. Supplied from a 3 V source for analog and a 1.8 V source for the output driver, it outputs data in serial mode via a single differential lane, which complies with the JESD204A standard. The integration of Serial Peripheral Interface (SPI) allows the user to easily configure the ADCs and the serial output modes. The device also includes a programmable full-scale SPI to allow a flexible input voltage range from 1 V (p-p) to 2 V (p-p). Excellent dynamic performance is maintained from the baseband to input frequencies of 170 MHz or more, making the ADC1413S ideal for use in communications, imaging, and medical applications. 2. Features and benefits  SNR, 72.1 dBFS; SFDR, 86 dBc  Sample rates up to 125 Msps  Single channel, 14-bit pipelined ADC core  3 V, 1.8 V power supplies  Flexible input voltage range: 1 V (p-p) to 2 V (p-p)  serial output  Compliant with JESD204A serial transmission standard  Pin compatible with the ADC1613S series, ADC1213S series, and ADC1113S125  Input bandwidth, 600 MHz  Power dissipation, 550 mW at 80 Msps  SPI register programming  Duty cycle stabilizer  High Intermediate Frequency (IF) capability  Offset binary, two’s complement, gray code  Power-down mode and Sleep mode  HVQFN32 package 3. Applications  Wireless and wired broadband communications  Spectral analysis  Ultrasound equipment  Portable instrumentation  Imaging systems ® ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 4. Ordering information Table 1. Ordering information Type number Sampling frequency (Msps) Package ADC1413S125HN-C1 125 HVQFN32R plastic thermal enhanced very thin quad flat package; SOT1152-1 no leads; 32 terminals; body 7  7  0.8 mm ADC1413S105HN-C1 105 HVQFN32R plastic thermal enhanced very thin quad flat package; SOT1152-1 no leads; 32 terminals; body 7  7  0.8 mm ADC1413S080HN-C1 80 HVQFN32R plastic thermal enhanced very thin quad flat package; SOT1152-1 no leads; 32 terminals; body 7  7  0.8 mm ADC1413S065HN-C1 65 HVQFN32R plastic thermal enhanced very thin quad flat package; SOT1152-1 no leads; 32 terminals; body 7  7  0.8 mm Name Description Version 5. Block diagram SDIO SCLK CS SPI SYNC_P SYNC_N CLKP DLL PLL CLKM ADC CORE 14-BIT PIPELINED D13 to D0 INM 8-bit 8-bit ENCODER 8-bit/10-bit A OTR T/H INPUT STAGE SCRAMBLER A INP FRAME ASSEMBLY ERROR CORRECTION AND DIGITAL PROCESSING SERIALIZER A CMLP OUTPUT BUFFER A CMLN 10-bit CLOCK INPUT STAGE & DUTY CYCLE CONTROL SYSTEM REFERENCE AND POWER MANAGEMENT ADC1413S OTR SENSE VDDD AGND DGND VDDA 005aaa196 Fig 1. Block diagram ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 2 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 6. Pinning information 25 SYNCP 26 SYNCN 27 VDDD 28 DGND 29 VDDA 30 AGND terminal 1 index area 31 SENSE 32 VREF 6.1 Pinning CLKP 1 24 n.c. CLKM 2 23 DGND AGND 3 22 DGND REFB 4 21 VDDD ADC1413S 7 18 VDDD INP 8 17 DGND 11 SCLK VDDA DGND 16 INM VDDD 15 19 CMLP OTR 14 6 CS 13 VCM SDIO 12 20 CMLN VDDA 10 5 9 REFT 005aaa200 Transparent top view Fig 2. Pinning diagram 6.2 Pin description Table 2. Pin description Symbol Pin Type [1] Description CLKP 1 I clock input CLKM 2 I complementary clock input AGND 3 G analog ground REFB 4 O ADC bottom reference REFT 5 O ADC top reference VCM 6 O ADC output common voltage INM 7 I ADC complementary analog input INP 8 I ADC analog input VDDA 9 P analog power supply 3 V VDDA 10 P analog power supply 3 V SCLK 11 I SPI clock SDIO 12 I/O SPI data input/output CS 13 I chip select ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 3 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 2. Pin description …continued Symbol Pin Type [1] Description OTR 14 O out-of-range information VDDD 15 P digital power supply 1.8 V DGND 16 G digital ground DGND 17 G digital ground VDDD 18 P digital power supply 1.8 V CMLP 19 O serial output CMLN 20 O serial complementary output VDDD 21 P digital power supply 1.8 V DGND 22 G digital ground DGND 23 G digital ground n.c. 24 - not connected SYNCP 25 I positive synchronization signal from the receiver SYNCN 26 I negative synchronization signal from the receiver VDDD 27 P digital power supply 1.8 V DGND 28 G digital ground VDDA 29 P analog power supply 3 V AGND 30 G analog ground SENSE 31 I reference programming pin VREF 32 I/O voltage reference input/output [1] P: power supply; G: ground; I: input; O: output; I/O: input/output. 7. Limiting values Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VDDA Conditions Min Max Unit analog supply voltage 0.4 +4.6 V VDDD(1V8) digital supply voltage (1.8 V) 0.4 +2.5 V Tstg storage temperature 55 +125 C Tamb ambient temperature 40 +85 C Tj junction temperature - 125 C ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 4 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 8. Thermal characteristics Table 4. Thermal characteristics Symbol Rth(j-a) Rth(j-c) [1] Parameter Conditions Typ Unit thermal resistance from junction to ambient [1] 25.6 K/W thermal resistance from junction to case [1] 8.6 K/W Value for six layers board in still air with a minimum of 25 thermal vias. 9. Static characteristics Table 5. Static characteristics [1] Symbol Parameter Conditions Min Typ Max Unit Supplies VDDA analog supply voltage 2.85 3.0 3.4 V VDDD(1V8) digital supply voltage (1.8 V) 1.65 1.8 1.95 V IDDA analog supply current fclk = 125 Msps; fi = 70 MHz - 185 - mA IDDD(1V8) digital supply current (1.8 V) fclk = 125 Msps; fi = 70 MHz - 75 - mA Ptot total power dissipation fclk = 125 Msps - 690 - mW fclk = 105 Msps - 625 - mW fclk = 80 Msps - 550 - mW fclk = 65 Msps - 495 - mW Power-down mode - 30 - mW Standby mode - 150 - mW P power dissipation Digital inputs Clock inputs: pins CLKP and CLKM (AC-coupled) Low-Voltage Positive Emitter-Coupled Logic (LVPECL) Vi(clk)dif differential clock input voltage peak-to-peak - 1.6 - V differential clock input voltage peak 0.8 3.0 - V Sine Vi(clk)dif Low Voltage Complementary Metal Oxide Semiconductor (LVCMOS) VIL LOW-level input voltage - - 0.3VDDA V VIH HIGH-level input voltage 0.7VDDA - - V SPI: pins CS, SDIO, and SCLK VIL LOW-level input voltage 0 - 0.3VDDA V VIH HIGH-level input voltage 0.7VDDA - VDDA V IIL LOW-level input current 10 - +10 A IIH HIGH-level input current 50 - +50 A CI input capacitance - 4 - pF ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 5 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 5. Symbol Static characteristics …continued[1] Parameter Conditions Min Typ Max Unit track mode 5 - +5 A Analog inputs: pins INP and INM II input current RI input resistance track mode - 15 -  CI input capacitance track mode - 5 - pF VI(cm) common-mode input voltage track mode 1.1 1.5 2 V Bi input bandwidth - 600 - MHz VI(dif) differential input voltage peak-to-peak 1 - 2 V Voltage controlled regulator output: pin VCM VO(cm) common-mode output voltage - 0.5VDDA - V IO(cm) common-mode output current - 4 - mA output 0.5 - 1 V input 0.5 - 1 V Reference voltage input/output: pin VREF VVREF voltage on pin VREF Data outputs: CMLP, CMLN Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 000 VOL VOH LOW-level output voltage DC-coupled; output - 1.5 - V AC-coupled - 1.35 - V HIGH-level output voltage DC-coupled; output - 1.8 - V AC-coupled - 1.65 - V Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 001 VOL VOH LOW-level output voltage DC-coupled; output - 1.45 - V AC-coupled - 1.275 - V HIGH-level output voltage DC-coupled; output - 1.8 - V AC-coupled - 1.625 - V Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 010 VOL VOH LOW-level output voltage DC-coupled; output - 1.4 - V AC-coupled - 1.2 - V HIGH-level output voltage DC-coupled; output - 1.8 - V AC-coupled - 1.6 - V Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 011 VOL LOW-level output voltage DC-coupled; output - 1.35 - V AC-coupled - 1.125 - V VOH HIGH-level output voltage DC-coupled; output - 1.8 - V AC-coupled - 1.575 - V Output levels, VDDD(1V8) = 1.8 V; SWING_SEL[2:0] = 100 VOL VOH LOW-level output voltage DC-coupled; output - 1.3 - V AC-coupled - 1.05 - V HIGH-level output voltage DC-coupled; output - 1.8 - V AC-coupled - 1.55 - V ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 6 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 5. Symbol Static characteristics …continued[1] Parameter Conditions Min Typ Max Unit Serial configuration: SYNCP, SYNCN VIL LOW-level input voltage differential; input - 0.95 - V VIH HIGH-level input voltage differential; input - 1.47 - V INL integral non-linearity 5 - +5 LSB DNL differential non-linearity 0.95 0.5 +0.95 LSB Eoffset offset error - 2 - mV EG gain error full-scale -  0.5 - % power supply rejection ratio 200 mV (p-p) on pin VDDA; fi = DC - 54 - dB Accuracy guaranteed no missing codes Supply PSRR [1] Typical values measured at VDDA = 3 V, VDDD(1V8) = 1.8 V, Tamb = 25 C. Minimum and maximum values are across the full temperature range Tamb = 40 C to +85 C at VDDA = 3 V, VDDD(1V8) = 1.8 V; Vi(INP)  Vi(INM) = 1 dBFS; internal reference mode; 100  differential applied to serial outputs; unless otherwise specified. ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 7 of 36 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Integrated Device Technology ADC1413S_SER 3 Product data sheet 10. Dynamic characteristics 10.1 Dynamic characteristics Table 6. Dynamic characteristics [1] Parameter Conditions Min Typ Max Min Typ Max Min Typ Max Min Typ Max 2H second harmonic level fi = 3 MHz - 87 - - 87 - - 86 - - 88 - dBc fi = 30 MHz - 86 - - 86 - - 86 - - 87 - dBc fi = 70 MHz - 85 - - 85 - - 84 - - 85 - dBc fi = 170 MHz - 82 - - 82 - - 81 - - 83 - dBc fi = 3 MHz - 86 - - 86 - - 85 - - 87 - dBc fi = 30 MHz - 85 - - 85 - - 85 - - 86 - dBc fi = 70 MHz - 84 - - 84 - - 83 - - 84 - dBc fi = 170 MHz - 81 - - 81 - - 80 - - 82 - dBc fi = 3 MHz - 83 - - 83 - - 82 - - 84 - dBc fi = 30 MHz - 82 - - 82 - - 82 - - 83 - dBc fi = 70 MHz - 81 - - 81 - - 80 - - 81 - dBc fi = 170 MHz - 78 - - 78 - - 77 - - 79 - dBc fi = 3 MHz - 11.7 - - 11.7 - - 11.6 - - 11.6 - bits fi = 30 MHz - 11.6 - - 11.5 - - 11.5 - - 11.5 - bits fi = 70 MHz - 11.5 - - 11.5 - - 11.4 - - 11.4 - bits 3H Rev. 03 — 2 July 2012 THD ENOB SFDR total harmonic distortion effective number of bits signal-to-noise ratio spurious-free dynamic range ADC1413S080 ADC1413S105 ADC1413S125 Unit 8 of 36 © IDT 2012. All rights reserved. fi = 170 MHz - 11.4 - - 11.4 - - 11.3 - - 11.3 - bits fi = 3 MHz - 72.1 - - 72.0 - - 71.8 - - 71.4 - dBFS fi = 30 MHz - 71.3 - - 71.2 - - 71.2 - - 71.1 - dBFS fi = 70 MHz - 70.7 - - 70.7 - - 70.6 - - 70.5 - dBFS fi = 170 MHz - 70.2 - - 70.1 - - 70.0 - - 69.9 - dBFS fi = 3 MHz - 86 - - 86 - - 85 - - 87 - dBc fi = 30 MHz - 85 - - 85 - - 85 - - 86 - dBc fi = 70 MHz - 84 - - 84 - - 83 - - 84 - dBc fi = 170 MHz - 81 - - 81 - - 80 - - 82 - dBc ADC1413S series SNR third harmonic level ADC1413S065 Single 14-bit ADC: serial JESD204A interface Symbol Symbol Dynamic characteristics …continued[1] Parameter Conditions ADC1413S065 Min IMD ct(ch) [1] intermodulation distortion channel crosstalk Typ Max ADC1413S080 Min Typ Max ADC1413S105 Min ADC1413S125 Typ Max Min Typ Max Integrated Device Technology ADC1413S_SER 3 Product data sheet Table 6. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Unit fi = 3 MHz - 89 - - 89 - - 88 - - 89 - dBc fi = 30 MHz - 88 - - 88 - - 88 - - 88 - dBc fi = 70 MHz - 87 - - 87 - - 86 - - 86 - dBc fi = 170 MHz - 84 - - 85 - - 83 - - 84 - dBc fi = 70 MHz - 100 - - 100 - - 100 - - 100 - dBc Typical values measured at VDDA = 3 V, VDDD(1V8) = 1.8 V, Tamb = 25 C and CL = 5 pF. Minimum and maximum values are across the full temperature range Tamb = 40 C to +85 C at VDDA = 3 V, VDDD(1V8) = 1.8 V; Vi(INP)  Vi(INM) = 1 dBFS; internal reference mode; 100  differential applied to serial outputs; unless otherwise specified. 10.2 Clock and digital output timing Table 7. Rev. 03 — 2 July 2012 Symbol Clock and digital output timing characteristics [1] Parameter Conditions ADC1413S065 Min Typ Max ADC1413S080 Min Typ Max ADC1413S105 Min Typ Max ADC1413S125 Min Typ Max Unit pins CLKP and CLKM clock frequency 45 - 65 60 - 80 75 - 105 100 - 125 Msps tlat(data) data latency time clock cycles 307 - 850 250 - 283 190 - 226 160 - 170 ns clk clock duty cycle DCS_EN = 1: en 30 50 70 30 50 70 30 50 70 30 50 70 % td(s) sampling delay time - 0.8 - - 0.8 - - 0.8 - - 0.8 - ns twake wake-up time - 76 - - 76 - - 76 - - 76 - ns Typical values measured at VDDA = 3 V, VDDD(1V8) = 1.8 V, Tamb = 25 C. Minimum and maximum values are across the full temperature range Tamb = 40 C to +85 C at VDDA = 3 V, VDDD(1V8) = 1.8 V; Vi(INP)  Vi(INM) = 1 dBFS; internal reference mode; 100  differential applied to serial outputs; unless otherwise specified. 9 of 36 © IDT 2012. All rights reserved. ADC1413S series [1] Single 14-bit ADC: serial JESD204A interface fclk ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 10.3 Serial output timing The eye diagram of the serial output is shown in Figure 3 and Figure 4. Test conditions are: • 3.125 Gbps data rate • Tamb = 25 °C • DC-coupling with two different receiver common-mode voltages 005aaa088 Fig 3. Eye diagram at 1 V receiver common-mode 005aaa089 Fig 4. Eye diagram at 2 V receiver common-mode ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 10 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 10.4 SPI timing Table 8. SPI timing characteristics [1] Symbol Parameter tw(SCLK) Min Typ Max Unit SCLK pulse width - 40 - ns tw(SCLKH) SCLK HIGH pulse width - 16 - ns tw(SCLKL) SCLK LOW pulse width - 16 - ns tsu set-up time data to SCLK HIGH - 5 - ns CS to SCLK HIGH - 5 - ns data to SCLK HIGH - 2 - ns CS to SCLK HIGH - 2 - ns - 25 - MHz hold time th fclk(max) [1] Conditions maximum clock frequency Typical values measured at VDDA = 3 V, VDDD(1V8) = 1.8 V, Tamb = 25 C. Minimum and maximum values are across the full temperature range Tamb = 40 C to +85 C at VDDA = 3 V, VDDD(1V8) = 1.8 V; Vi(INP)  Vi(INM) = 1 dBFS; internal reference mode; 100  differential applied to serial outputs; unless otherwise specified. tsu tsu th CS tw(SCLKL) th tw(SCLKH) tw(SCLK) SCLK SDIO R/W W1 W0 A12 A11 D2 D1 D0 005aaa065 Fig 5. SPI timing ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 11 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 11. Application information 11.1 Analog inputs 11.1.1 Input stage description The analog input of the ADC1413S supports a differential or a single-ended input drive. Optimal performance is achieved using differential inputs with the common-mode input voltage (VI(cm)) on pins INP and INM set to 0.5VDDA. The full-scale analog input voltage range is configurable between 1 V (p-p) and 2 V (p-p) via a programmable internal reference (see Section 11.2 and Table 21). Figure 6 shows the equivalent circuit of the sample-and-hold input stage, including ElectroStatic Discharge (ESD) protection and circuit and package parasitics. package ESD parasitics switch INP Ron = 15 Ω 8 Cs internal clock switch Ron = 15 Ω INM 7 Cs internal clock 005aaa185 Fig 6. Input sampling circuit The sample phase occurs when the internal clock (derived from the clock signal on pin CLKP/CLKM) is HIGH. The voltage is then held on the sampling capacitors. When the clock signal goes LOW, the stage enters the hold phase and the voltage information is transmitted to the ADC core. ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 12 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 11.1.2 Anti-kickback circuitry Anti-kickback circuitry (RC filter in Figure 7) is needed to counteract the effects of a charge injection generated by the sampling capacitance. The RC filter is also used to filter noise from the signal before it reaches the sampling stage. The value of the capacitor should be chosen to maximize noise attenuation without degrading the settling time excessively. R INP C R INM 005aaa073 Fig 7. Anti-kickback circuit The component values are determined by the input frequency and should be selected so as not to affect the input bandwidth. Table 9. RC coupling versus input frequency, typical values Input frequency (MHz) Resistance () Capacitance (pF) 3 25 12 70 12 8 170 12 8 11.1.3 Transformer The configuration of the transformer circuit is determined by the input frequency. The configuration shown in Figure 8 would be suitable for a baseband application. ADT1-1WT 100 nF analog input 25 Ω 100 nF INP 25 Ω 12 pF 100 nF 100 nF 25 Ω 25 Ω INM VCM 100 nF 100 nF 005aaa044 Fig 8. Single transformer configuration ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 13 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface The configuration shown in Figure 9 is recommended for high frequency applications. In both cases, the choice of transformer is a compromise between cost and performance. ADT1-1WT analog input 100 nF ADT1-1WT 50 Ω 12 Ω INP 50 Ω 8.2 pF 50 Ω 100 nF 50 Ω 12 Ω INM VCM 100 nF 100 nF 005aaa045 Fig 9. Dual transformer configuration 11.2 System reference and power management 11.2.1 Internal/external reference The ADC1413S has a stable and accurate built-in internal reference voltage to adjust the ADC full-scale. This reference voltage can be set internally via SPI or with pins VREF and SENSE (see Figure 11 to Figure 14), in 1 dB steps between 0 dB and 6 dB, via SPI control bits INTREF[2:0] (when bit INTREF_EN = logic 1; see Table 21). The equivalent reference circuit is shown in Figure 10. External reference is also possible by providing a voltage on pin VREF as described in Figure 14. ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 14 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface REFT REFERENCE AMP REFB VREF EXT_ref BUFFER EXT_ref BANDGAP REFERENCE ADC CORE SENSE SELECTION LOGIC 005aaa164 Fig 10. Reference equivalent schematic Table 10 shows how to choose between the different internal/external modes: Table 10. Reference modes Mode SPI bit, “Internal reference” SENSE pin VREF pin Full-scale, (V (p-p)) Internal (Figure 11) 0 GND 330 pF capacitor 2 to GND Internal (Figure 12) 0 VREF pin = SENSE pin and 330 pF capacitor to GND 1 Internal, SPI mode (Figure 13) 1 VREF pin = SENSE pin and 330 pF capacitor to GND 1 to 2 External (Figure 14) 0 VDDA External voltage 1 to 2 from 0.5 V to 1 V Figure 11 to Figure 14 illustrate how to connect the SENSE and VREF pins to select the required reference voltage source. ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 15 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface VREF VREF 330 pF 330 pF REFERENCE EQUIVALENT SCHEMATIC REFERENCE EQUIVALENT SCHEMATIC SENSE SENSE 005aaa116 005aaa117 Fig 11. Internal reference, 2 V (p-p) full-scale Fig 12. Internal reference, 1 V (p-p) full-scale VREF VREF V 330 pF REFERENCE EQUIVALENT SCHEMATIC SENSE 0.1 μF REFERENCE EQUIVALENT SCHEMATIC SENSE VDDA 005aaa118 Fig 13. Internal reference via SPI, 1 V (p-p) to 2 V (p-p) full-scale 005aaa119 Fig 14. External reference, 1 V (p-p) to 2 V (p-p) full-scale 11.2.2 Programmable full-scale The full-scale is programmable between 1 V (p-p) to 2 V (p-p) (see Table 11). Table 11. Reference modes INTREF[2:0] Level Full-scale (V (p-p)) 000 0 dB 2 001 1 dB 1.78 010 2 dB 1.59 011 3 dB 1.42 100 4 dB 1.26 101 5 dB 1.12 110 6 dB 1 111 not used x ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 16 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 11.2.3 Common-mode output voltage (VO(cm)) An 0.1 F filter capacitor should be connected between pin VCM and ground to ensure a low-noise common-mode output voltage. When AC-coupled, these pins can be used to set the common-mode reference for the analog inputs, for instance via a transformer middle point. package ESD parasitics COMMON-MODE REFERENCE 1.5 V VCM 0.1 μF ADC core 005aaa051 Fig 15. Reference equivalent schematic 11.2.4 Biasing The common-mode input voltage (VI(cm)) on pins INP and INM should be set externally to 0.5VDDA for optimal performance and should always be between 0.9 V and 2 V. 11.3 Clock input 11.3.1 Drive modes The ADC1413S can be driven differentially (LVPECL). It can also be driven by a single-ended LVCMOS signal connected to pin CLKP (CLKM should be connected to ground via a capacitor). LVCMOS clock input CLKP CLKP CLKM LVCMOS clock input 005aaa174 a. Rising edge LVCMOS CLKM 005aaa053 b. Falling edge LVCMOS Fig 16. LVCMOS single-ended clock input ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 17 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Sine clock input CLKP Sine clock input CLKP CLKM CLKM 005aaa054 005aaa173 a. Sine clock input b. Sine clock input (with transformer) CLKP LVPECL clock input CLKM 005aaa172 c. LVPECL clock input Fig 17. Differential clock input 11.3.2 Equivalent input circuit The equivalent circuit of the input clock buffer is shown in Figure 18. The common-mode voltage of the differential input stage is set via internal 5 k resistors. package ESD parasitics CLKP Vcm(clk) SE_SEL SE_SEL 5 kΩ 5 kΩ CLKM 005aaa081 Vcm(clk) = common-mode voltage of the differential input stage. Fig 18. Equivalent input circuit ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 18 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Single-ended or differential clock inputs can be selected via the SPI (see Table 20). If single-ended is selected, the input pin (CLKM or CLKP) is selected via control bit SE_SEL. If single-ended is implemented without setting bit SE_SEL accordingly, the unused pin should be connected to ground via a capacitor. 11.3.3 Duty cycle stabilizer The duty cycle stabilizer can improve the overall performance of the ADC by compensating the input clock signal duty cycle. When the duty cycle stabilizer is active (bit DCS_EN = logic 1; see Table 20), the circuit can handle signals with duty cycles of between 30 % and 70 % (typical). When the duty cycle stabilizer is disabled (DCS_EN = logic 0), the input clock signal should have a duty cycle of between 45 % and 55 %. Table 12. Duty cycle stabilizer bit DCS_EN Description 0 duty cycle stabilizer disable 1 duty cycle stabilizer enable 11.3.4 Clock input divider The ADC1413S contains an input clock divider that divides the incoming clock by a factor of 2 (when bit CLKDIV2_SEL = logic 1; see Table 20). This feature allows the user to deliver a higher clock frequency with better jitter performance, leading to a better SNR result once acquisition has been performed. 11.4 Digital outputs 11.4.1 Serial output equivalent circuit The JESD204A standard specifies that if the receiver and the transmitter are DC-coupled both must be fed from the same supply. VDDD VDDD 50 Ω 50 Ω CMLP 100 Ω RECEIVER CMLN + 12 mA to 26 mA AGND 005aaa197 Fig 19. CML output connection to the receiver (DC-coupling) The output should be terminated when 100  (typical) is reached at the receiver side. ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 19 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface VDDD 50 Ω 50 Ω CMLP 10 nF 100 Ω CMLN RECEIVER 10 nF - + 12 mA to 26 mA 005aaa187 Fig 20. CML output connection to the receiver (AC-coupling) 11.5 JESD204A serializer For more information about the JESD204A standard refer to the JEDEC web site. 11.5.1 Digital JESD204A formatter The block placed after the ADC cores is used to implement all functions of the JESD204A standard. This ensures signal integrity and guarantees the clock and the data recovery at the receiver side. The block is highly parameterized and can be configured in various ways depending on the sampling frequency and the number of lanes used. M CONVERTERS L LANES N bits from Cr0 + CS bits for control F octets TX transport layer FRAME TO OCTETS SCRAMBLER SYNC~ ALIGNMENT CHARACTER GENERATOR 8-bit/ 10-bit SER LANE 0 TX CONTROLLER N' = N + CS S samples per frame cycle CF: position of controls bits HD: frame boundary break Padding with Tails bits (TT) M × (N' × S) bits L × (F) octets L octets 005aaa198 Fig 21. General overview of the JESD204A serializer ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 20 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface ADC_MODE[1:0] PRBS DUMMY SCR_IN_MODE 11 14 + 1 10 14 + 1 N AND CS LANE_MODE[1:0] 8 N + CS PLL AND DLL 14 + 1 00 FRAME ASSEMBLY ×1 frame CLK ×F character CLK × 10F 8-bit/ 10-bit SCR PRBS ADC_PD ADC 00 01 FSM (frame assembly, character replication, ILA, test mode) 10 00 '0' 01 '0/1' 10 PRBS 11 LANE_POL SER SWING_SEL[2:0] bit CLK 005aaa199 sync_request Fig 22. Detailed view of the JESD204A serializer with debug functionality 11.5.2 ADC core output codes versus input voltage Table 13 shows the data output codes for a given analog input voltage. Table 13. Output codes versus input voltage INP-INM (V) Offset binary Two’s complement OTR < 1 00 0000 0000 0000 10 0000 0000 0000 1 1 00 0000 0000 0000 10 0000 0000 0000 0 0.9998779 00 0000 0000 0001 10 0000 0000 0001 0 0.9997559 00 0000 0000 0010 10 0000 0000 0010 0 0.9996338 00 0000 0000 0011 10 0000 0000 0011 0 0.9995117 00 0000 0000 0100 10 0000 0000 0100 0 .... .... .... 0 0.0002441 01 1111 1111 1110 11 1111 1111 1110 0 0.0001221 01 1111 1111 1111 11 1111 1111 1111 0 0 10 0000 0000 0000 00 0000 0000 0000 0 +0.0001221 10 0000 0000 0001 00 0000 0000 0001 0 +0.0002441 10 0000 0000 0010 00 0000 0000 0010 0 .... .... .... 0 +0.9995117 11 1111 1111 1011 01 1111 1111 1011 0 +0.9996338 11 1111 1111 1100 01 1111 1111 1100 0 +0.9997559 11 1111 1111 1101 01 1111 1111 1101 0 +0.9998779 11 1111 1111 1110 01 1111 1111 1110 0 +1 11 1111 1111 1111 01 1111 1111 1111 0 > +1 11 1111 1111 1111 01 1111 1111 1111 1 ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 21 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 11.6 Serial Peripheral Interface (SPI) 11.6.1 Register description The ADC1413S serial interface is a synchronous serial communications port allowing easy interfacing with many industry microprocessors. It provides access to the registers that control the operation of the chip in both read and write modes. This interface is configured as a 3-wire type (SDIO as bidirectional pin). Pin SCLK acts as the serial clock and pin CS acts as the serial chip select. Each read/write operation is sequenced by the CS signal and enabled by a LOW level to to drive the chip with N bytes, depending on the content of the instruction byte (see Table 14). Table 14. Instruction bytes for the SPI MSB LSB Bit 7 6 5 Description R/W[1] W1 A7 A6 [1] 4 3 2 1 0 W0 A12 A11 A10 A9 A8 A5 A4 A3 A2 A1 A0 R/W indicates whether a read or write transfer occurs after the instruction byte. Table 15. Read or Write mode access description R/W[1] Description 0 Write mode operation 1 Read mode operation [1] Bits W1 and W0 indicate the number of bytes transferred. ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 22 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 16. Number of bytes to be transferred W1 W0 Number of bytes transferred 0 0 1 byte 0 1 2 bytes 1 0 3 bytes 1 1 4 or more bytes Bits A12 to A0 indicate the address of the register being accessed. In the case of a multiple byte transfer, this address is the first register to be accessed. An address counter is incremented to access subsequent addresses. The steps involved in a data transfer are as follows: 1. The falling edge on pin CS in combination with a rising edge on pin SCLK determine the start of communications. 2. The first phase is the transfer of the 2-byte instruction. 3. The second phase is the transfer of the data which can be vary in length but is always a multiple of 8 bits. The MSB is always sent first (for instruction and data bytes). 4. A rising edge on pin CS indicates the end of data transmission. CS SCLK SDIO R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 Instruction bytes D4 D3 D2 Register N (data) D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Register N + 1 (data) 005aaa086 Fig 23. Transfer diagram for two data bytes (3-wire type) ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 23 of 36 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Table 17. Integrated Device Technology ADC1413S_SER 3 Product data sheet 11.6.2 Channel control Register allocation map Address Register name (hex) Access[1] Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Default[2] Bin - - - - - - ENABLE - 1111 1111 SW_RST - - - - - Bit definition ADC control register Rev. 03 — 2 July 2012 0003 SPI control R/W 0005 Reset and R/W Operating modes 0006 Clock R/W - - - SE_SEL DIFF_SE 0008 Vref R/W - - - - INTREF_EN 0013 Offset R/W - - 0014 Test pattern 1 R/W - - 0015 Test pattern 2 R/W 0016 Test pattern 3 R/W PD[1:0] CLKDIV2_SEL 0000 0000 DCS_EN INTREF[2:0] 0000 0000 DIG_OFFSET[5:0] - - - 0000 0000 TESTPAT_1[2:0] 0000 0000 TESTPAT_2[13:6] TESTPAT_3[5:0] 0000 000* 0000 0000 - - 0 0 POR_TST - 0000 0000 JESD204A control R RXSYNC_ ERROR 0802 Ser_Reset R/W SW_RST 0 0 0 FSM_SW_ RST 0 0 0 0000 0000 0805 Ser_Control1 R/W 0 RESERVED SYNC_ POL SYNC_ SINGLE_ ENDED 1 REV_ SCR REV_ ENCODER REV_ SERIAL 0100 1001 0 0 0 0808 Ser_Analog_Ctrl R/W 0 0809 Ser_ScramblerA R/W 0 RESERVED[2:0] 0 LSB_INIT[6:0] RESERVED 0100 0000 SWING_SEL[2:0] 0000 0011 0000 0000 24 of 36 © IDT 2012. All rights reserved. ADC1413S series Ser_Status Single 14-bit ADC: serial JESD204A interface 0801 Register allocation map …continued Address Register name (hex) Access[1] 080A Ser_ScramblerB R/W 080B Ser_PRBS_Ctrl R/W 0820 Cfg_0_DID R 0821 Cfg_1_BID R/W* 0 0 0 0 0822 Cfg_3_SCR_L R/W* SCR 0 0 0 0 0823 Cfg_4_F R/W* 0 0 0 0 0 0824 Cfg_5_K R/W* 0 0 0 0825 Cfg_6_M R/W* 0 0 0 0 0826 Cfg_7_CS_N R/W* 0 CS[0] 0 0 Bit definition Bit 7 Bit 6 Bit 5 Bit 4 0 0 0 0 Bit 3 Bit 2 Bit 1 Bit 0 MSB_INIT[7:0] 0 Default[2] Bin 1111 1111 0 PRBS_TYPE[1:0] DID[7:0] 0000 0000 1110 1101 BID[3:0] 0 0000 1010 0 L F[2:0] 0000 0000 0000 0*** K[4:0] 0 Integrated Device Technology ADC1413S_SER 3 Product data sheet Table 17. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx 000* **** 0 0 M N[3:0] 0000 000* 0827 Cfg_8_Np R 0 0 0 0828 Cfg_9_S R/W* 0 0 0 0 0 NP[4:0] 0 0000 1111 0829 Cfg_10_HD_CF R/W* HD 0 0 0 0 0 082D Cfg_02_2_LID R/W* 0 0 0 084D Cfg02_13_FCHK R 0871 Lane_0_Ctrl R/W 0 SCR_IN_ MODE LANE_MODE[1:0] 0 LANE_ POL 0 LANE_PD 0000 0000 0891 ADC_0_Ctrl R/W 0 0 ADC_MODE[1:0] 0 0 0 ADC_PD 0000 0000 0 S CF[1:0] 0000 0000 *000 0000 LID[4:0] 0001 1100 FCHK[7:0] **** **** an "*" in the Access column means that this register is subject to control access conditions in Write mode. [2] an "*" in the Default column replaces a bit of which the value depends on the binary level of external pins (e.g. CFG[3:0], Swing[1:0], Scrambler). 25 of 36 © IDT 2012. All rights reserved. ADC1413S series [1] Single 14-bit ADC: serial JESD204A interface Rev. 03 — 2 July 2012 0100 0100 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 11.6.3 Register description 11.6.3.1 ADC control registers Table 18. Register SPI control (address 0003h) Default values are highlighted. Bit Symbol Access Value Description 7 to 2 - - 111111 not used 1 ENABLE R/W 0 - - ADC SPI control enable: 0 ADC does not get the next SPI command 1 ADC gets the next SPI command 1 not used Table 19. Register Reset and Power-down mode (address 0005h) Default values are highlighted. Bit Symbol Access 7 SW_RST R/W 6 to 2 - - 1 to 0 PD[1-0] R/W Value Description reset digital part: 0 no reset 1 performs a reset of the digital part 00000 not used Power-down mode: 00 normal (power-up) 01 full power-down 10 sleep 11 normal (power-up) Table 20. Register Clock (address 0006h) Default values are highlighted. Bit Symbol Access Value Description 7 to 5 - - 000 not used 4 SE_SEL R/W 3 DIFF_SE - - 1 CLKDIV2_SEL R/W DCS_EN select CLKM input 1 select CLKP input R/W 2 0 select SE clock input pin: 0 differential/single-ended clock input select: 0 fully differential 1 single-ended 0 not used select clock input divider by 2: 0 disable 1 enable R/W duty cycle stabilizer enable: 0 disable 1 enable ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 26 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 21. Register Vref (address 0008h) Default values are highlighted. Bit Symbol Access Value Description 7 to 4 - - 0000 not used 3 INTREF_EN R/W enable internal programmable VREF mode: 0 disable 1 2 to 0 INTREF[2:0] R/W enable programmable internal reference: 000 0 dB (FS = 2 V) 001 1 dB (FS = 1.78 V) 010 2 dB (FS = 1.59 V) 011 3 dB (FS = 1.42 V) 100 4 dB (FS = 1.26 V) 101 5 dB (FS = 1.12 V) 110 6 dB (FS = 1 V) 111 not used Table 22. Digital offset adjustment (address 0013h) Default values are highlighted. Register offset Decimal DIG_OFFSET[5:0] +31 011111 +31 LSB ... ... ... 0 000000 0 ... ... ... 32 100000 32 LSB Table 23. Register Test pattern 1 (address 0014h) Default values are highlighted. Bit Symbol Access Value Description 7 to 3 - - 00000 not used 2 to 0 TESTPAT_1[2:0] R/W digital test pattern: 000 off 001 mid-scale 010  FS 011 + FS 100 toggle ‘1111..1111’/’0000..0000’ 101 custom test pattern, to be written in register 0015h and 0016h 110 ‘010101...’ 111 ‘101010...’ ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 27 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 24. Register Test pattern 2 (address 0015h) Default values are highlighted. Bit Symbol Access Value 7 to 0 TESTPAT_2[13:6] R/W 00000000 custom digital test pattern (bit 13 to 6) Description Table 25. Register Test pattern 3 (address 0016h) Default values are highlighted. Bit Symbol Access Value Description 7 to 3 TESTPAT_3[5:0] R/W 00000 custom digital test pattern (bit 5 to 0) 2 to 0 - - 000 not used 11.6.4 JESD204A digital control registers Table 26. SER_Status (address 0801h) Default values are highlighted. Bit Symbol Access Value Description 7 RXSYNC_ERROR R/W 0 set to 1 when a synchronization error occurs 6 to 4 RESERVED[2:0] - 100 reserved 3 to 2 - - 00 not used 1 POR_TST - 0 power-on-reset 0 RESERVED - 0 reserved Table 27. SER_Reset (address 0802h) Default values are highlighted. Bit Symbol Access Value Description 7 SW_RST R/W 0 initiates a software reset of the JEDEC204A unit 6 to 4 - - 000 not used 3 FSM_SW_RST R/W 0 initiates a software reset of the internal state machine of JEDEC204A unit 2 to 0 - - 000 not used Table 28. SER_Control1 (address 0805h) Default values are highlighted. Bit Symbol Access Value Description 7 - - 0 not used 6 RESERVED R/W 0 reserved 5 SYNC_POL R/W 4 defines the sync signal polarity: 0 synchronization signal is active low 1 synchronization signal is active high SYNC_SINGLE_ENDED R/W defines the input mode of the sync signal: 0 1 3 - - 2 REV_SCR - 1 synchronization input mode is set in Differential mode synchronization input mode is set in Single-ended mode not used LSB are swapped to MSB at the scrambler input: 0 disable 1 enable ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 28 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 28. SER_Control1 (address 0805h) …continued Default values are highlighted. Bit Symbol Access 1 REV_ENCODER - 0 REV_SERIAL Value Description LSB are swapped to MSB at the 8-bit/10-bit encoder input 0 disable 1 enable - LSB are swapped to MSB at the lane input: 0 disable 1 enable Table 29. SER_Analog_Ctrl (address 0808h) Default values are highlighted. Bit Symbol Access Value Description 7 to 3 - - 00000 not used 2 to 0 SWING_SEL[2:0] R/W 011 defines the swing output for the lane pads Table 30. SER_ScramblerA (address 0809h) Default values are highlighted. Bit Symbol Access Value Description 7 - - 0 not used 6 to 0 LSB_INIT[6:0] R/W 0000000 defines the initialization vector for the scrambler polynomial (lower) Table 31. SER_ScramblerB (address 080Ah) Default values are highlighted. Bit Symbol Access Value Description 7 to 0 MSB_INIT[7:0] R/W 11111111 defines the initialization vector for the scrambler polynomial (upper) Table 32. SER_PRBS_Ctrl (address 080Bh) Default values are highlighted. Bit Symbol Access Value Description 7 to 2 1 to 0 - - 000000 not used PRBS_TYPE[1:0] R/W defines the type of Pseudo-Random Binary Sequence (PRBS) generator to be used: 00 (reset) PRBS-7 01 PRBS-7 10 PRBS-23 11 PRBS-31 Table 33. Cfg_0_DID (address 0820h) Default values are highlighted. Bit Symbol Access Value Description 7 to 0 DID[7:0] R 11101101 defines the device (= link) identification number ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 29 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 34. Cfg_1_BID (address 0821h) Default values are highlighted. Bit Symbol Access Value Description 7 to 4 - - 0000 not used 3 to 0 BID[3:0] R/W 1010 defines the bank ID – extension to DID Table 35. Cfg_3_SCR_L (address 0822h) Default values are highlighted. Bit Symbol Access Value Description 7 SCR R/W 0 scrambling enabled 6 to 1 - - 000000 not used 0 L R/W 0 defines the number of lanes per converter device, minus 1 Description Table 36. Cfg_4_F (address 0823h) Default values are highlighted. Bit Symbol Access Value 7 to 3 - - 00000 not used 2 to 0 F[2:0] R/W *** defines the number of octets per frame, minus 1 Table 37. Cfg_5_K (address 0824h) Default values are highlighted. Bit Symbol Access Value Description 7 to 5 - - 000 not used 4 to 0 K[4:0] R/W ***** defines the number of frames per multiframe, minus 1 Table 38. Cfg_6_M (address 0825h) Default values are highlighted. Bit Symbol Access Value Description 7 to 1 - - 0000000 not used 0 M R/W * defines the number of converters per device, minus 1 Table 39. Cfg_7_CS_N (address 0826h) Default values are highlighted. Bit Symbol Access Value Description 7 - - 0 not used 6 CS[0] R/W 1 defines the number of control bits per sample, minus 1 5 to 4 - - 00 not used 3 to 0 N[3:0] R/W 0100 defines the converter resolution Table 40. Cfg_8_Np (address 0827h) Default values are highlighted. Bit Symbol Access Value Description 7 to 5 - - 000 not used 4 to 0 NP[4:0] R/W 01111 defines the total number of bits per sample, minus 1 ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 30 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 41. Cfg_9_S (address 0828h) Default values are highlighted. Bit Symbol Access Value Description 7 to 1 - - 0000000 not used 0 S R/W 0 defines number of samples per converter per frame cycle Table 42. Cfg_10_HD_CF (address 0829h) Default values are highlighted. Bit Symbol Access Value Description 7 HD R/W * defines high density format 6 to 2 - - 00000 not used 1 to 0 CF[1:0] R/W 00 defines number of control words per frame clock cycle per link. Value Description Table 43. Cfg02_2_LID (address 082Dh) Default values are highlighted. Bit Symbol Access 7 to 5 - - 000 not used 4 to 0 LID[4:0] R/W 11100 defines lane identification number Table 44. Cfg01_13_FCHK (address 084Dh) Default values are highlighted. Bit Symbol Access Value Description 7 to 0 FCHK[7:0] R ******** defines the checksum value for lane checksum corresponds to the sum of all the link configuration parameters module 256 (as defined in JEDEC Standard No.204A) Table 45. Lane_0_Ctrl (address 0871h) Default values are highlighted. Bit Symbol Access Value Description 7 - - 0 not used 6 SCR_IN_MODE R/W 5 to 4 3 LANE_MODE[1:0] - defines the input type for scrambler and 8-bit/10-bit units: 0 (reset) (normal mode) = Input of the scrambler and 8-bit/10-bit units is the output of the frame assembly unit. 1 input of the scrambler and 8-bit/10-bit units is the PRSB generator (PRBS type is defined with “PRBS_TYPE[1:0]” (Ser_PRBS_ctrl register) R/W - defines output type of Lane output unit: 00 (reset) normal mode: Lane output is the 8-bit/10-bit output unit 01 constant mode: Lane output is set to a constant (0  0) 10 toggle mode: Lane output is toggling between 0  0 and 0  1 11 PRBS mode: Lane output is the PRBS generator (PRBS type is defined with “PRBS_TYPE[1:0]” (Ser_PRBS_ctrl register) 0 not used ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 31 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface Table 45. Lane_0_Ctrl (address 0871h) …continued Default values are highlighted. Bit Symbol Access 2 LANE_POL R/W 1 RESERVED R/W 0 Lane_PD R/W Value Description defines lane polarity: 0 lane polarity is normal 1 lane polarity is inverted 0 reserved lane power-down control: 0 lane is operational 1 lane is in Power-down mode Table 46. ADC_0_Ctrl (address 0891h) Default values are highlighted. Bit Symbol Access Value Description 7 to 6 - - 00 not used 5 to 4 ADC_MODE[1:0] R/W 3 to 1 - - 0 ADC_PD R/W defines input type of JESD204A unit 00 (reset) ADC output is connected to the JESD204A input 01 not used 10 JESD204A input is fed with a dummy constant, set to: OTR = 0 and ADC[13:0] = “10011011101010” 11 JESD204A is fed with a PRBS generator (PRBS type is defined with “PRBS_TYPE[1:0]” (Ser_PRBS_ctrl register) 000 not used ADC power-down control: 0 ADC is operational 1 ADC is in Power-down mode ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 32 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 12. Package outline HVQFN32R: plastic thermal enhanced very thin quad flat package; no leads; 32 terminals; resin based; body 7 x 7 x 0.8 mm B D SOT1152-1 A terminal 1 index area A E detail X e1 e ∅v ∅w b C A B C C 1/2 e L1 9 y y1 C 16 L 8 17 e Eh e2 1/2 e 1 24 terminal 1 index area 32 25 X Dh 0 2.5 5 mm scale Dimensions Unit mm A b max 0.90 0.28 nom 0.80 0.23 min 0.75 0.18 D Dh E 7.1 7.0 6.9 4.05 4.00 3.95 7.1 7.0 6.9 Eh e e1 e2 L L1 4.05 0.55 0.10 4.00 0.65 4.55 4.55 0.50 0.05 3.95 0.45 0.00 v 0.1 w y 0.05 0.08 y1 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included References Outline version IEC JEDEC JEITA SOT1152-1 --- --- --- sot1152-1_po European projection Issue date 09-10-13 09-11-16 Fig 24. Package outline SOT1152-1 (HVQFN32) ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 33 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 13. Abbreviations Table 47. Abbreviations Acronym Description ADC Analog-to-Digital Converter DCS Duty Cycle Stabilizer ESD ElectroStatic Discharge IF Intermediate Frequency IMD InterModulation Distortion LSB Least Significant Bit LVCMOS Low-Voltage Complementary Metal-Oxide Semiconductor LVPECL Low-Voltage Positive Emitter-Coupled Logic MSB Most Significant Bit OTR OuT-of-Range PRBS Pseudo-Random Binary Sequence SFDR Spurious-Free Dynamic Range SNR Signal-to-Noise Ratio SPI Serial Peripheral Interface TX Transmitter ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 34 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 14. Revision history Table 48. Revision history Document ID Release date Data sheet status Change notice Supersedes ADC1413S_SER v.3 20120702 Product data sheet - ADC1413S_SER v.2 ADC1413S_SER v.2 20110608 Product data sheet - ADC1413S_SER v.1 Modifications: ADC1413S_SER v.1 • Section 10.2 “Clock and digital output timing” has been updated. 20110314 Product data sheet - - 15. Contact information For more information or sales office addresses, please visit: http://www.idt.com ADC1413S_SER 3 Product data sheet © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 35 of 36 ADC1413S series Integrated Device Technology Single 14-bit ADC: serial JESD204A interface 16. Contents 1 2 3 4 5 6 6.1 6.2 7 8 9 10 10.1 10.2 10.3 10.4 11 11.1 11.1.1 11.1.2 11.1.3 11.2 11.2.1 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Thermal characteristics . . . . . . . . . . . . . . . . . . 5 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . . 8 Dynamic characteristics . . . . . . . . . . . . . . . . . . 8 Clock and digital output timing . . . . . . . . . . . . . 9 Serial output timing . . . . . . . . . . . . . . . . . . . . . 10 SPI timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Application information. . . . . . . . . . . . . . . . . . 12 Analog inputs . . . . . . . . . . . . . . . . . . . . . . . . . 12 Input stage description . . . . . . . . . . . . . . . . . . 12 Anti-kickback circuitry . . . . . . . . . . . . . . . . . . . 13 Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . 13 System reference and power management . . 14 Internal/external reference . . . . . . . . . . . . . . . 14 11.2.2 Programmable full-scale . . . . . . . . . . . . . . . . 11.2.3 Common-mode output voltage (VO(cm)) . . . . . 11.2.4 Biasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3 Clock input . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3.1 Drive modes. . . . . . . . . . . . . . . . . . . . . . . . . . 11.3.2 Equivalent input circuit . . . . . . . . . . . . . . . . . . 11.3.3 Duty cycle stabilizer . . . . . . . . . . . . . . . . . . . . 11.3.4 Clock input divider . . . . . . . . . . . . . . . . . . . . . 11.4 Digital outputs . . . . . . . . . . . . . . . . . . . . . . . . 11.4.1 Serial output equivalent circuit . . . . . . . . . . . . 11.5 JESD204A serializer . . . . . . . . . . . . . . . . . . . 11.5.1 Digital JESD204A formatter . . . . . . . . . . . . . . 11.5.2 ADC core output codes versus input voltage . 11.6 Serial Peripheral Interface (SPI) . . . . . . . . . . 11.6.1 Register description . . . . . . . . . . . . . . . . . . . . 11.6.2 Channel control . . . . . . . . . . . . . . . . . . . . . . . 11.6.3 Register description . . . . . . . . . . . . . . . . . . . . 11.6.3.1 ADC control registers. . . . . . . . . . . . . . . . . . . 11.6.4 JESD204A digital control registers . . . . . . . . 12 Package outline. . . . . . . . . . . . . . . . . . . . . . . . 13 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 14 Revision history . . . . . . . . . . . . . . . . . . . . . . . 15 Contact information . . . . . . . . . . . . . . . . . . . . 16 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADC1413S_SER 3 Product data sheet 16 17 17 17 17 18 19 19 19 19 20 20 21 22 22 24 26 26 28 33 34 35 35 36 © IDT 2012. All rights reserved. Rev. 03 — 2 July 2012 36 of 36