HIP2100IRZT

DATASHEET HIP2100 FN4022 Rev.16.00 Aug 8, 2019 100V/2A Peak, Low Cost, High Frequency Half Bridge Driver The HIP2100 is a high frequency, 100V Half Bridge N-Channel power MOSFET driver IC. The low-side and high-side gate drivers are independently controlled and matched to 8ns. This gives the user maximum flexibility in dead-time selection and driver protocol. Undervoltage protection on both the low-side and high-side supplies force the outputs low. An on-chip diode eliminates the discrete diode required with other driver ICs. A new level-shifter topology yields the low-power benefits of pulsed operation with the safety of DC operation. Unlike some competitors, the high-side output returns to its correct state after a momentary undervoltage of the high-side supply. Features Applications • Drives 1000pF Load with Rise and Fall Times Typ 10ns • Telecom Half Bridge Power Supplies • Avionics DC/DC Converters • Two-Switch Forward Converters • Drives N-Channel MOSFET Half Bridge • SOIC, EPSOIC, and QFN Package Options • SOIC and EPSOIC Packages Compliant with 100V Conductor Spacing Guidelines of IPC-2221 • Pb-Free (RoHS Compliant) • Bootstrap Supply Max Voltage to 114VDC • On-Chip 1Ω Bootstrap Diode • Fast Propagation Times for Multi-MHz Circuits • CMOS Input Thresholds for Improved Noise Immunity • Independent Inputs for Non-Half Bridge Topologies • No Start-Up Problems • Active Clamp Forward Converters • Outputs Unaffected by Supply Glitches, HS Ringing Below Ground, or HS Slewing at High dv/dt Related Literature • Low Power Consumption For a full list of related documents, visit our website: • HIP2100 device page • Wide Supply Range • Supply Undervoltage Protection • 3Ω Driver Output Resistance • QFN Package: - Compliant to JEDEC PUB95 MO-220 QFN - Quad Flat No Leads - Package Outline - Near Chip Scale Package Footprint, which Improves PCB Efficiency and has a Thinner Profile FN4022 Rev.16.00 Aug 8, 2019 Page 1 of 14 HIP2100 Ordering Information PART NUMBER (Notes 2, 3) PART MARKING TEMP. RANGE (°C) TAPE AND REEL (Units) (Note 1) PACKAGE (RoHS Compliant) PKG. DWG. # HIP2100IBZ 2100 IBZ -40 to +125 - 8 Ld SOIC M8.15 HIP2100IBZT 2100 IBZ -40 to +125 2.5k 8 Ld SOIC M8.15 HIP2100EIBZ 2100 EIBZ -40 to +125 - 8 Ld EPSOIC M8.15C HIP2100EIBZT 2100 EIBZ -40 to +125 2.5k 8 Ld EPSOIC M8.15C HIP2100IRZ HIP 2100IRZ -40 to +125 - 16 Ld 5x5 QFN L16.5x5 HIP2100IRZT HIP 2100IRZ -40 to +125 6k 16 Ld 5x5 QFN L16.5x5 HIP2100EVAL2 Evaluation Board NOTES: 1. See TB347 for details about reel specifications. 2. These Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J-STD-020. 3. For Moisture Sensitivity Level (MSL), see the HIP2100 device page. For more information about MSL, see TB363. Pinouts (16 LD QFN) TOP VIEW LO 7 VSS HO 3 6 LI HS 4 5 HI EPAD NC 8 2 LO 1 HB VDD VDD NC (8 LD SOIC, EPSOIC) TOP VIEW 16 15 14 13 NC 1 12 NC HB 2 11 VSS EPAD 9 5 6 7 8 NC NC 4 HI 10 LI HS HO 3 NC EPAD = Exposed PAD. NC Pin Descriptions SYMBOL DESCRIPTION VDD Positive Supply to lower gate drivers. De-couple this pin to VSS. Bootstrap diode connected to HB. HB High-Side Bootstrap supply. External bootstrap capacitor is required. Connect positive side of bootstrap capacitor to this pin. Bootstrap diode is on-chip. HO High-Side Output. Connect to gate of High-Side power MOSFET. HS High-Side Source connection. Connect to source of High-Side power MOSFET. Connect negative side of bootstrap capacitor to this pin. HI High-Side input. LI Low-Side input. VSS Chip negative supply, generally will be ground. LO Low-Side Output. Connect to gate of Low-Side power MOSFET. EPAD Exposed Pad. Connect to ground or float. The EPAD is electrically isolated from all other pins. FN4022 Rev.16.00 Aug 8, 2019 Page 2 of 14 HIP2100 Application Block Diagram +12V +100V SECONDARY CIRCUIT VDD HB DRIVE HI PWM CONTROLLER LI CONTROL HI HO HS DRIVE LO LO REFERENCE AND ISOLATION HIP2100 VSS Functional Block Diagram HB VDD UNDER VOLTAGE HO LEVEL SHIFT DRIVER HS HI UNDER VOLTAGE LO DRIVER LI VSS EPAD (EPSOIC and QFN PACKAGES ONLY) *EPAD = Exposed Pad. The EPAD is electrically isolated from all other pins. For best thermal performance connect the EPAD to the PCB power ground plane. FN4022 Rev.16.00 Aug 8, 2019 Page 3 of 14 HIP2100 +48V +12V PWM HIP2100 SECONDARY CIRCUIT ISOLATION FIGURE 1. TWO-SWITCH FORWARD CONVERTER +48V SECONDARY CIRCUIT +12V PWM HIP2100 ISOLATION FIGURE 2. FORWARD CONVERTER WITH AN ACTIVE CLAMP FN4022 Rev.16.00 Aug 8, 2019 Page 4 of 14 HIP2100 Absolute Maximum Ratings Thermal Information Supply Voltage, VDD, VHB-VHS (Notes 4, 5) . . . . . . . . -0.3V to 18V LI and HI Voltages (Note 5) . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V Voltage on LO (Note 4) . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V Voltage on HO (Note 4) . . . . . . . . . . . . . . . VHS -0.3V to VHB +0.3V Voltage on HS (Continuous) (Note 4) . . . . . . . . . . . . . . -1V to 110V Voltage on HB (Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +118V Average Current in VDD to HB diode . . . . . . . . . . . . . . . . . . . 100mA ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 (1kV) Thermal Resistance (Typical) Maximum Recommended Operating Conditions JA (°C/W) JC (°C/W) 95 50 SOIC (Note 6) . . . . . . . . . . . . . . . . . . . EPSOIC (Note 7) . . . . . . . . . . . . . . . . . 40 3.0 QFN (Note 7) . . . . . . . . . . . . . . . . . . . . 37 6.5 Max Power Dissipation at +25°C in Free Air (SOIC, Note 6) . . . . 1.3W Max Power Dissipation at +25°C in Free Air (EPSOIC, Note 7). . 3.1W Max Power Dissipation at +25°C in Free Air (QFN, Note 7) . . . . . 3.3W Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Junction Temperature Range. . . . . . . . . . . . . . . . . .-55°C to +150°C Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493 Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . +9V to 14.0VDC Voltage on HS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to 100V Voltage on HS. . . . . . . . . . . . . . . .(Repetitive Transient) -5V to 105V Voltage on HB . . . VHS +8V to VHS +14.0V and VDD -1V to VDD +100V HS Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .