ICS180M-52LF

DATASHEET ICS180-52 LOW EMI CLOCK GENERATOR Description Features The ICS180-52 generates a low EMI output clock from a clock or crystal input. The device uses IDT’s proprietary mix of analog and digital Phase-Locked Loop (PLL) technology to spread the frequency spectrum of the output, thereby reducing the frequency amplitude peaks by several dB. • • • • Pin and function compatible to Cypress W180-52 Packaged in 8-pin SOIC Provides a spread spectrum output clock Accepts a clock input and provides same frequency dithered output • Input frequency of 8 to 15 MHz • Peak reduction by 7dB - 14dB typical on 3rd - 19th The ICS180-52 offers center spread selection of +/-0.625% and +/-1.875%. Refer to the MK1714-01/02 for the widest selection of input frequencies and multipliers. odd harmonics • Spread percentage selection for +/-0.625% and +/-1.875% IDT offers a complete line of EMI reducing clock generators. Consult us when you need to remove crystals and oscillators from your board. • Operating voltage of 3.3 V and 5 V • Advanced, low-power CMOS process Block Diagram VDD FS1 SSON# PLL Clock Synthesis and Spread Spectrum Circuitry SS% X1/CLKIN X2 Clock Buffer/ Crystal Oscillator CLK GND IDT™ / ICS™ LOW EMI CLOCK GENERATOR 1 ICS180-52 REV C 051310 ICS180-52 LOW EMI CLOCK GENERATOR SSCG Pin Assignment Spread Spectrum Select Table X1/CLKIN 1 8 SSON# X2 2 7 FS1 GND 3 6 VDD SS% 4 5 CLKOUT SS% (Pin 4) Spread Direction Spread Percentage (%) 0 1 Center Center +/-0.625% +/1.875% 0 = connect to GND 1 = connect directly to VDD Note: SS% pin has an internal pull-up resistor 8-pin (150 mil) SOIC Frequency Range Selection Table FS1 (Pin 7) Frequency Range Selection (MHz) 0 1 8-10 10-15 Pin Descriptions Pin Number Pin Name Pin Type 1 X1/CLKIN Input 2 X2 Output Crystal output. Float for a clock input. 3 GND Power Connect to ground. 4 SS% Input Select pin for spread amount. See table above. Internal pull-up resistor. 5 CLKOUT Output Spread spectrum clock output per table above. 6 VDD Power Connect to 3.3 V or 5 V. 7 FS1 Input Select pin for input frequency. See table above. Internal pull-up resistor. 8 SSON# Input Spread Spectrum Control. This pin enables spread spectrum when low. Internal pull-down resistor. IDT™ / ICS™ LOW EMI CLOCK GENERATOR Pin Description Crystal or Clock Input. 2 ICS180-52 REV C 051310 ICS180-52 LOW EMI CLOCK GENERATOR SSCG External Components PCB Layout Recommendations The ICS180-52 requires a minimum number of external components for proper operation. For optimum device performance and lowest output phase noise, the following guidelines should be observed. Decoupling Capacitor 1) The 0.01µF decoupling capacitor should be mounted on the component side of the board as close to the VDD pin as possible. No vias should be used between the decoupling capacitor and VDD pin. The PCB trace to VDD pin should be kept as short as possible, as should the PCB trace to the ground via. A decoupling capacitor of 0.01µF must be connected between VDD and GND on pins 6 and 3, as close to these pins as possible. For optimum device performance, the decoupling capacitor should be mounted on the component side of the PCB. Avoid the use of vias in the decoupling circuit. 2) To minimize EMI, the 33Ω series termination resistor (if needed) should be placed close to the clock output. Series Termination Resistor When the PCB trace between the clock output and the load is over 1 inch, series termination should be used. To series terminate a 50Ω trace (a commonly used trace impedance) place a 33Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20Ω. 3) An optimum layout is one with all components on the same side of the board, minimizing vias through other signal layers. Other signal traces should be routed away from the ICS180-52. This includes signal traces just underneath the device, or on layers adjacent to the ground plane layer used by the device. value of these capacitors is given by the following equation: Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS180-52. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature 0 to +70° C Storage Temperature -65 to +150° C Junction Temperature 125° C Soldering Temperature 260° C Recommended Operation Conditions Parameter Min. Ambient Operating Temperature Power Supply Voltage (measured in respect to GND) IDT™ / ICS™ LOW EMI CLOCK GENERATOR 3 Typ. Max. Units 0 +70 °C +3.135 +5.5 V ICS180-52 REV C 051310 ICS180-52 LOW EMI CLOCK GENERATOR SSCG DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature 0 to +70° C Parameter Symbol Conditions Min. Typ. 3.135 Max. Units 3.465 V 32 mA Operating Voltage VDD Supply Current IDD Input High Voltage VIH Input Low Voltage VIL Output High Voltage VOH IOH = -4 mA VDD-0.4 V Output High Voltage VOH IOH = -15 mA 2.4 V Output Low Voltage VOL IOL = 15 mA Input Capacitance CIN 5 Output Impedance Rout 25 ohms 500 KΩ No load 18 2.4 0.8 Input Pull-up Resistor Power-up Time V First locked clock cycle after steady power V 0.4 V 7 pF 5 ms Unless stated otherwise, VDD = 5 V, ±10%, Ambient Temperature 0 to +70° C Parameter Symbol Conditions Min. Typ. Max. Units 4.5 5 5.5 V 30 50 mA Operating Voltage VDD Supply Current IDD Input High Voltage VIH Input Low Voltage VIL Output High Voltage VOH IOH = -24 mA Output Low Voltage VOL IOL = 24 mA Output Impedance Rout 20 Input Capacitance CIN 5 No load 0.7VDD 0.15VDD IDT™ / ICS™ LOW EMI CLOCK GENERATOR 2.4 4 V ohms 7 500 First locked clock cycle after steady power V V 0.4 Input Pull-up Resistor Power-up Time V pF KΩ 5 ICS180-52 ms REV C 051310 ICS180-52 LOW EMI CLOCK GENERATOR SSCG AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V±5% or 5 V±10%, Ambient Temperature 0 to +70° C, CL=15 pf Parameter Symbol Conditions Input/Output Clock Frequency Min. Typ. Max. Units 8 15 MHz 60 % 50 60 % Input Clock Duty Cycle Time above VDD/2 40 Output Clock Duty Cycle Note 1 40 Output Rise Time tOR 0.8 to 2.4 V, note 1 2 5 ns Output Fall Time tOF 2.4 to 0.8 V, note 1 2 5 ns 250 300 ps Jitter Cycle-to-cycle Note 1: Measured with 15 pF load Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case Symbol Conditions Min. Typ. Max. Units θJA Still air 150 ° C/W θJA 1 m/s air flow 140 ° C/W θJA 3 m/s air flow 120 ° C/W 40 ° C/W θJC Marking Diagram 8 5 180M52LF ###### YYWW 1 4 Notes: 1. ###### is the lot number. 2. YYWW is the last two digits of the year and week that the part was assembled. 3. “LF” denotes Pb (lead) free package. 4. Bottom marking: country of origin. IDT™ / ICS™ LOW EMI CLOCK GENERATOR 5 ICS180-52 REV C 051310 ICS180-52 LOW EMI CLOCK GENERATOR SSCG Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 8 Symbol E Min A A1 B C D E e H h L α H INDEX AREA 1 2 D A Inches Max Min 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0° 8° Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .1890 .1968 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0° 8° h x 45 A1 C -Ce B SEATING PLANE L .10 (.004) C Ordering Information Part / Order Number Marking Shipping packaging Package Temperature 180M-52LF 180M-52LFT see page 5 Tubes Tape and Reel 8-pin SOIC 8-pin SOIC 0 to +70° C 0 to +70° C “LF” denotes Pb free packaging. While the information presented herein has been checked for both accuracy and reliability, IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT™ / ICS™ LOW EMI CLOCK GENERATOR 6 ICS180-52 REV C 051310 ICS180-52 LOW EMI CLOCK GENERATOR SSCG Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.