DATASHEET
ICS181-52
LOW EMI CLOCK GENERATOR
Description
Features
The ICS181-52 generates a low EMI output clock from
a clock or crystal input. The device uses IDT’s
proprietary mix of analog and digital Phase Locked
Loop (PLL) technology to spread the frequency
spectrum of the output, thereby reducing the frequency
amplitude peaks by several dB.
•
•
•
•
The ICS181-52 offers center spread selection of
+/-0.625% and +/-1.875%. Refer to the MK1714-01/02
for the widest selection of input frequencies and
multipliers.
• Input frequency of 28 to 48 MHz for Clock input
• Peak reduction by 7dB - 14dB typical on 3rd - 19th
Pin and function compatible to Cypress W181-52
Packaged in 8-pin SOIC
Provides a spread spectrum output clock
Accepts a clock input and provides same frequency
dithered output
odd harmonics
• Spread percentage selection for +/-0.625% and
IDT offers a complete line of EMI reducing clock
generators. Consult us when you need to remove
crystals and oscillators from your board.
+/-1.875%
• Operating voltage of 3.3 V and 5 V
• Advanced, low-power CMOS process
NOTE: EOL for non-green parts to occur on
5/13/10 per PDN U-09-01
Block Diagram
VDD
FS1
SSON#
PLL Clock
Synthesis
and Spread
Spectrum
Circuitry
SS%
X1/CLKIN
X2
Clock Buffer/
Crystal
Oscillator
CLK
GND
IDT™ / ICS™ LOW EMI CLOCK GENERATOR
1
ICS181-52
REV B 081009
ICS181-52
LOW EMI CLOCK GENERATOR
SSCG
Pin Assignment
Spread Spectrum Select Table
X1/CLKIN
1
8
SSON#
X2
2
7
FS1
GND
3
6
VDD
SS%
4
5
CLKOUT
SS%
(Pin 4)
Spread
Direction
Spread
Percentage (%)
0
1
Center
Center
+/-0.625%
+/1.875%
0 = connect to GND
1 = connect directly to VDD
Note: SS% pin has an internal pull-up resistor
8-pin (150 mil) SOIC
Frequency Range Selection Table
FS1
(Pin 7)
Frequency
Range Selection
MHz
0
1
28-38
38-48
Pin Descriptions
Pin
Number
Pin
Name
Pin Type
1
X1/CLKIN
Input
2
X2
Output
Crystal output. Float for a clock input.
3
GND
Power
Connect to ground.
4
SS%
Input
Select pin for spread amount. See table above. Internal pull-up resistor.
5
CLKOUT
Output
Spread spectrum clock output per table above.
6
VDD
Power
Connect to 3.3 V or 5 V.
7
FS1
Input
Select pin for input frequency. See table above. Internal pull-up resistor.
8
SSON#
Input
Spread Spectrum Control. This pin enables spread spectrum when low.
Internal pull-down resistor.
IDT™ / ICS™ LOW EMI CLOCK GENERATOR
Pin Description
Crystal or Clock Input.
2
ICS181-52
REV B 081009
ICS181-52
LOW EMI CLOCK GENERATOR
SSCG
External Components
PCB Layout Recommendations
The ICS181-52 requires a minimum number of external
components for proper operation.
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
Decoupling Capacitor
1) The 0.01µF decoupling capacitor should be mounted
on the component side of the board as close to the VDD
pin as possible. No vias should be used between the
decoupling capacitor and VDD pin. The PCB trace to
VDD pin should be kept as short as possible, as should
the PCB trace to the ground via.
A decoupling capacitor of 0.01µF must be connected
between VDD and GND on pins 6 and 3, as close to
these pins as possible. For optimum device
performance, the decoupling capacitor should be
mounted on the component side of the PCB. Avoid the
use of vias in the decoupling circuit.
2) To minimize EMI the 33Ω series termination resistor,
if needed, should be placed close to the clock output.
Series Termination Resistor
When the PCB trace between the clock output and the
load is over 1 inch, series termination should be used.
To series terminate a 50Ω trace (a commonly used trace
impedance) place a 33Ω resistor in series with the clock
line, as close to the clock output pin as possible. The
nominal impedance of the clock output is 20Ω.
3) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers. Other signal traces should be routed away
from the ICS181-52. This includes signal traces just
underneath the device, or on layers adjacent to the
ground plane layer used by the device.
value of these capacitors is given by the following
equation:
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICS181-52. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Item
Rating
Supply Voltage, VDD
7V
All Inputs and Outputs
-0.5 V to VDD+0.5 V
Ambient Operating Temperature
0 to +70° C
Storage Temperature
-65 to +150° C
Junction Temperature
125° C
Soldering Temperature
260° C
Recommended Operation Conditions
Parameter
Min.
Ambient Operating Temperature
Power Supply Voltage (measured in respect to GND)
IDT™ / ICS™ LOW EMI CLOCK GENERATOR
3
Typ.
Max.
Units
0
+70
°C
+3.135
+5.5
V
ICS181-52
REV B 081009
ICS181-52
LOW EMI CLOCK GENERATOR
SSCG
DC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V ± 5%, Ambient Temperature 0 to +70° C
Parameter
Symbol
Conditions
Min.
Typ.
Units
3.465
V
32
mA
Operating Voltage
VDD
Supply Current
IDD
Input High Voltage
VIH
Input Low Voltage
VIL
Output High Voltage
VOH
IOH = -4 mA
VDD-0.4
V
Output High Voltage
VOH
IOH = -15 mA
2.4
V
Output Low Voltage
VOL
IOL = 15 mA
Input Capacitance
CIN
All pins except CLKIN
CLKIN pin only
Output Impedance
3.135
Max.
No load
18
2.4
0.8
Rout
Input Pull-up Resistor
Power-up Time
V
V
0.4
V
5
7
pF
6
10
pF
25
ohms
500
KΩ
First locked clock
cycle after steady
power
5
ms
Unless stated otherwise, VDD = 5 V, ±10%, Ambient Temperature 0 to +70° C
Parameter
Symbol
Conditions
Operating Voltage
VDD
Supply Current
IDD
Input High Voltage
VIH
Input Low Voltage
VIL
Output High Voltage
VOH
IOH = -24 mA
Output Low Voltage
VOL
IOL = 24 mA
Output Impedance
Rout
Input Capacitance
CIN
IDT™ / ICS™ LOW EMI CLOCK GENERATOR
Typ.
Max.
Units
4.5
5
5.5
V
30
50
mA
No load
0.7VDD
V
0.15VDD
2.4
V
V
0.4
20
V
ohms
All pins except CLKIN
5
7
pF
CLKIN pin only
6
10
pF
Input Pull-up Resistor
Power-up Time
Min.
500
First locked clock
cycle after steady
power
4
KΩ
5
ICS181-52
ms
REV B 081009
ICS181-52
LOW EMI CLOCK GENERATOR
SSCG
AC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V±5% or 5 V±10%, Ambient Temperature 0 to +70° C, CL=15 pf
Parameter
Symbol
Conditions
Min.
Typ.
Max. Units
Input/Output Clock Frequency
28
48
MHz
Input Crystal Frequency
28
40
MHz
60
%
50
60
%
Input Clock Duty Cycle
Time above VDD/2
40
Output Clock Duty Cycle
Note 1
40
Output Rise Time
tOR
0.8 to 2.4 V, note 1
2
5
ns
Output Fall Time
tOF
2.4 to 0.8 V, note 1
2
5
ns
250
300
ps
Jitter
Cycle-to-cycle
Note 1: Measured with 15 pF load
Thermal Characteristics
Parameter
Thermal Resistance Junction to
Ambient
Thermal Resistance Junction to Case
Symbol
Conditions
Min.
Typ.
Max. Units
θJA
Still air
150
° C/W
θJA
1 m/s air flow
140
° C/W
θJA
3 m/s air flow
120
° C/W
40
° C/W
θJC
Marking Diagram
8
5
Notes:
1. ###### is the lot number.
181M-52
######
YYWW
2. YYWW is the last two digits of the year and week that
the part was assembled.
3. “LF” denotes Pb (lead) free package.
1
4
4. Bottom marking: country of origin.
Marking Diagram (Pb free)
8
5
181M52LF
######
YYWW
1
IDT™ / ICS™ LOW EMI CLOCK GENERATOR
4
5
ICS181-52
REV B 081009
ICS181-52
LOW EMI CLOCK GENERATOR
SSCG
Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
8
Symbol
E
Min
A
A1
B
C
D
E
e
H
h
L
α
H
INDEX
AREA
1 2
D
A
Inches
Max
Min
1.35
1.75
0.10
0.25
0.33
0.51
0.19
0.25
4.80
5.00
3.80
4.00
1.27 BASIC
5.80
6.20
0.25
0.50
0.40
1.27
0°
8°
Max
.0532
.0688
.0040
.0098
.013
.020
.0075
.0098
.1890
.1968
.1497
.1574
0.050 BASIC
.2284
.2440
.010
.020
.016
.050
0°
8°
h x 45
A1
C
-Ce
B
SEATING
PLANE
L
.10 (.004)
C
Ordering Information
Part / Order Number
181M-52*
181M-52T*
181M-52LF
181M-52LFT
Marking
Shipping packaging
Package
see page 5
Tubes
Tape and Reel
Tubes
Tape and Reel
8-pin SOIC
8-pin SOIC
8-pin SOIC
8-pin SOIC
Temperature
0 to +70°
0 to +70°
0 to +70°
0 to +70°
C
C
C
C
*NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01
“LF” denotes Pb free packaging.
While the information presented herein has been checked for both accuracy and reliability, IDT assumes no responsibility for
either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits,
patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such
as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not
recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without
notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.
IDT™ / ICS™ LOW EMI CLOCK GENERATOR
6
ICS181-52
REV B 081009
ICS181-52
LOW EMI CLOCK GENERATOR
SSCG
Innovate with IDT and accelerate your future networks. Contact:
www.IDT.com
For Sales
For Tech Support
800-345-7015
408-284-8200
Fax: 408-284-2775
www.idt/com/go/clockhelp
Corporate Headquarters
Integrated Device Technology, Inc.
www.idt.com
© 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device
Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered
trademarks used to identify products or services of their respective owners.
Printed in USA
很抱歉,暂时无法提供与“ICS181M-52”相匹配的价格&库存,您可以联系我们找货
免费人工找货