ICS570GI-01

DATASHEET ICS570-01 MULTIPLIER AND ZERO DELAY BUFFER Description Features The ICS570-01 is a high-performance Zero Delay Buffer (ZDB) which integrates IDT’s proprietary mixed signal Phased Lock Loop (PLL) techniques. The zero delay feature means that the rising edge of the input clock aligns with the rising edges of the output clock, giving the appearance of no delay through the device. The device includes an on-chip ROM table with nine different mulitplication factors, allowing it to generate many common output frequencies from a single input. • • • • • • • • • • 8-pin MSOP package (3.00 mm x 3.00 mm body) Available in Pb (lead) free package Low input to output skew of 300 ps max Can recover degraded input clock duty cycle Output clock duty cycle of 45/55 Power Down and Tri-State Mode Accepts spread spectrum clock inputs Advanced, low power CMOS process 3.3 V operation Industrial temperature version available Block Diagram Power S1:0 2 ICLK PLL CLK FBIN GND IDT™ / ICS™ MULTIPLIER AND ZERO DELAY BUFFER 1 ICS570-01 REV B 072706 ICS570-01 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Pin Assignment ICLK 1 8 S1 S0 2 7 VDD GND 3 6 VDD FBIN 4 5 CLKOUT Pin Descriptions Pin Number 1 2 3 4 5 6 7 8 Pin Name ICLK S0 GND FBIN CLKOUT VDD VDD S1 Pin Type Input Input Power Input Output Power Power Input Pin Description Clock input. Select pin 0 for output clock. Connect to GND, VDD, or float per multiplier table. Connect to ground. Feedback clock input. Clock output with 5x multiplier. Connect to 3.3 V supply. Connect to 3.3 V supply. Select pin 1 for output clock. Connect to GND, VDD, or float per multiplier table. Clock Multiplier Table S1 S0 Multiplier ICLK Range 0 0 0 M M M 1 1 1 0 M 1 0 M 1 0 M 1 4x 5.333x 5x 2.5x 2x 3.333x 6x 3x 8x 7 - 24 MHz 8 - 20 MHz 7 - 22 MHz 11 - 44 MHz 13 - 55 MHz 10 - 33 MHz 7 - 18 MHz 11 - 37 MHz 5 - 13 MHz Note: For selections marked “M”, the pin is left floating. IDT™ / ICS™ MULTIPLIER AND ZERO DELAY BUFFER 2 ICS570-01 REV B 072706 ICS570-01 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER External Components The ICS570-01 requires a minimum number of external components for proper operation. Decoupling capacitors of 0.01 µF should be connected between VDD and GND (pins 3, 6, and 7), as close to the device as possible. A series termination resistor of 33Ω may be used on each clock output pin to reduce reflections. Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS570-01. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature, Commercial version 0 to +70° C Ambient Operating Temperature, Industrial version -40 to +85° C Storage Temperature -65 to +150° C Junction Temperature 125° C Soldering Temperature 260° C Recommended Operation Conditions Parameter Min. Ambient Operating Temperature -40 Power Supply Voltage (measured in respect to GND) IDT™ / ICS™ MULTIPLIER AND ZERO DELAY BUFFER Typ. 3 +3.15 +3.3 Max. Units +85 °C +3.45 V ICS570-01 REV B 072706 ICS570-01 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature -40 to +85° C Parameter Symbol Conditions Min. Typ. Max. Units 3.45 V Operating Voltage VDD 3.15 Operating Current IDD VDD=3.3 V Input High Voltage VIH ICLK, FBIN Input Low Voltage VIL ICLK, FBIN Input High Voltage, mid-level input VIH S0, S1 Input Low Voltage, mid-level input VIL S0, S1 Output High Voltage (CMOS High) VOH IOH = -4 mA VDD-0.4 V Output High Voltage VOH IOH = -12 mA 2.4 V Output Low Voltage VOL IOL = 12mA Short Circuit Current IOS Input Capacitance CIN 16 mA 2 V 0.8 VDD-0.5 V V 0.5 0.4 V V ±70 mA 5 pF ICLK, FBIN, S0, S1 AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature -40 to +85° C Parameter Symbol Conditions Min. Input Frequency, ICLK Typ. Max. Units See page 2 MHz Output Clock Frequency MHz Input to Feedback Skew 300 ps Part-to-part Skew 700 ps 200 ps Input to Output Jitter ICLK to FBIN Output Clock Rise Time 20% to 80%, Note1 1.2 2.5 ns Output Clock Fall Time 80% to 20%, Note 1 1.2 2.5 ns Output Clock Duty Cycle Measured at VDD/2, Note 1 45 50 55 % Min. Typ. Note 1: Measured with a 15 pF load. Thermal Characteristics Parameter Symbol Thermal Resistance Junction to Ambient θJA Thermal Resistance Junction to Case θJC IDT™ / ICS™ MULTIPLIER AND ZERO DELAY BUFFER Conditions Still air 4 Max. Units 95 ° C/W 48 ° C/W ICS570-01 REV B 072706 ICS570-01 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Package Outline and Package Dimensions (8-pin MSOP, 3.00 mm Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 8 Symbol E1 A A1 A2 b C D E E1 e L α aaa E IN D E X AREA 1 2 D Min Max -1.10 0 0.15 0.79 0.97 0.22 0.38 0.08 0.23 3.00 BASIC 4.90 BASIC 3.00 BASIC 0.65 Basic 0.40 0.80 0° 8° 0.10 Inches* Min Max -0.043 0 0.006 0.031 0.038 0.008 0.015 0.003 0.009 0.118 BASIC 0.193 BASIC 0.118 BASIC 0.0256 Basic 0.016 0.032 0° 8° 0.004 *For reference only. Controlling dimensions in mm. A 2 A A 1 c -C e b S E A T IN G P LA N E L aaa C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature ICS570GI-01LF ICS570GI-01LFT GI1L GI1L Tubes Tape and Reel 8-pin MSOP 8-pin MSOP -40 to +85° C -40 to +85° C Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT™ / ICS™ MULTIPLIER AND ZERO DELAY BUFFER 5 ICS570-01 REV B 072706 ICS570-01 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Revision History Rev. Originator Date Description of Change A K. Beckmeyer 01/25/06 New device/datasheet; Preliminary release. B J. Sarma 07/27/06 Added marking information; added new document format; released from Preliminary to final. IDT™ / ICS™ MULTIPLIER AND ZERO DELAY BUFFER 6 ICS570-01 REV B 072706 ICS570-01 MULTIPLIER AND ZERO DELAY BUFFER ZDB AND MULTIPLIER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA