DATASHEET
ISL28191, ISL28291
FN6156
Rev 10.00
July 22, 2014
Single and Dual Single Supply Ultra-Low Noise, Low Distortion Rail-to-Rail
Output, Op Amp
The ISL28191 and ISL28291 are tiny single and dual ultra-low
noise, ultra-low distortion operational amplifiers. They are fully
specified to operate down to +3V single supply. These
amplifiers have outputs that swing rail-to-rail and an input
common mode voltage that extends to ground
(ground sensing).
The ISL28191 and ISL28291 are unity gain stable with an
input referred voltage noise of 1.7nV/Hz. Both parts feature
0.00018% THD+N at 1kHz.
Features
• 1.7nV/√Hz input voltage noise at 1kHz
• 1kHz THD+N typical 0.00018% at 2VP-P VOUT
• Harmonic Distortion -76dBc, -70dBc, fo = 1MHz
• 61MHz -3dB bandwidth
• 630µV maximum offset voltage
• 3µA input bias current
The ISL28191 is available in the space-saving 6 Ld UTDFN
(1.6mmx1.6mm) and 6 Ld SOT-23 packages. The ISL28291 is
available in the 8 Ld SOIC, 10 Ld 1.8mmx1.4mm UTQFN and
10 Ld MSOP packages. All devices are guaranteed over -40°C
to +125°C.
• 100dB typical CMRR
Ordering Information
• Enable pin (not available in the 8 Ld SOIC package option)
PART NUMBER
(Note 5)
PART
MARKING
PACKAGE
(Pb-free)
PKG.
DWG. #
• 3V to 5.5V single supply voltage range
• Rail-to-rail output
• Ground Sensing
• Pb-free (RoHS compliant)
Applications
ISL28191FHZ-T7 (Notes 1, 2) GABJ
(Note 4)
6 Ld SOT-23 P6.064A
ISL28191FRUZ-T7 (Notes 1, 3) M8
6 Ld UTDFN L6.1.6x1.6A
• Low noise microphones/preamplifiers
ISL28291FUZ (Note 2)
8291Z
10 Ld MSOP M10.118A
• ADC buffers
ISL28291FUZ-T7 (Notes 1, 2) 8291Z
10 Ld MSOP M10.118A
• DAC output amplifiers
• Low noise signal processing
28291 FBZ 8 Ld SOIC
M8.15E
• Digital scales
ISL28291FBZ-T7 (Notes 1, 2) 28291 FBZ 8 Ld SOIC
M8.15E
• Strain gauges/sensor amplifiers
ISL28291FBZ (Note 2)
ISL28291FRUZ-T7 (Notes 1, 3) F
10 Ld UTQFN L10.1.8x1.4A
• Radio systems
ISL28191EVAL1Z
Evaluation Board
• Portable equipment
ISL28291EVAL1Z
Evaluation Board
• Infrared detectors
NOTES:
1. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pbfree material sets, molding compounds/die attach materials, and
100% matte tin plate plus anneal (e3 termination finish, which is
RoHS compliant and compatible with both SnPb and Pb-free
soldering operations). Intersil Pb-free products are MSL classified
at Pb-free peak reflow temperatures that meet or exceed the Pbfree requirements of IPC/JEDEC J STD-020.
Related Literature
• AN1343: ISL2829xEVAL1Z, ISL5529xEVAL1Z Evaluation
Board User’s Guide
3. These Intersil Pb-free plastic packaged products employ special Pbfree material sets; molding compounds/die attach materials and
NiPdAu plate - e4 termination finish, which is RoHS compliant and
compatible with both SnPb and Pb-free soldering operations.
Intersil Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
4. The part marking is located on the bottom of the part.
5. For Moisture Sensitivity Level (MSL), please see device information
page for ISL28191, ISL28291. For more information on MSL please
see techbrief TB363.
FN6156 Rev 10.00
July 22, 2014
Page 1 of 18
ISL28191, ISL28291
Pin Configurations
ISL28191
(6 LD 1.6X1.6X0.5 UTDFN)
TOP VIEW
ISL28191
(6 LD SOT-23)
TOP VIEW
OUT 1
V- 2
IN+ 3
OUT 1
6 V+
5 EN
IN- 2
5 EN
4 IN-
IN+ 3
IN-_A 2
IN+_A 3
V- 4
OUT_A 1
8 V+
+
+
4 V-
ISL28291
(10 LD MSOP)
TOP VIEW
ISL28291
(8 LD SOIC)
TOP VIEW
OUT_A 1
- +
+ -
6 V+
7 OUT_B
IN-_A 2
6 IN-_B
IN+_A 3
V- 4
5 IN+_B
EN_A 5
10 V+
9 OUT_B
+
+
8 IN-_B
7 IN+_B
6 EN_B
IN-_A
OUT_A
V+
OUT_B
ISL28291
(10 LD UTQFN)
TOP VIEW
10
9
8
1
7
FN6156 Rev 10.00
July 22, 2014
6 IN+_B
3
4
5
EN_A
EN_B
2
V-
IN+_A
IN-_B
+
+
Page 2 of 18
ISL28191, ISL28291
Pin Descriptions
ISL28191
(6 Ld SOT-23)
ISL28191
(6 Ld UTDFN)
4
2
ISL28291
(8 Ld SOIC)
ISL28291
(10 Ld MSOP)
ISL28291
(10 Ld UTQFN)
PIN
NAME
2 (A)
6 (B)
2 (A)
8 (B)
1 (A)
7 (B)
ININ-_A
IN-_B
FUNCTION
EQUIVALENT CIRCUIT
Inverting input
V+
IN-
IN+
VCircuit 1
3
3 (A)
5 (B)
3 (A)
7 (B)
2 (A)
6 (B)
IN+
IN+_B
IN+_B
4
4
3
V-
1 (A)
7 (B)
1 (A)
9 (B)
10 (A)
8 (B)
OUT
OUT_A
OUT_B
3
2
4
1
1
Non-inverting
input
(See circuit 1)
Negative supply
Output
V+
OUT
VCircuit 2
6
6
8
5
5
N/A
FN6156 Rev 10.00
July 22, 2014
10
9
V+
5 (A)
6 (B)
4 (A)
5 (B)
EN
EN_A
EN_B
Positive supply
Enable BAR
pin internal
pull-down; Logic
“1” selects the
disabled state;
Logic “0” selects
the enabled
state.
V+
EN
VCircuit 3
Page 3 of 18
ISL28191, ISL28291
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5V
Supply Turn On Voltage Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs
Differential Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.5V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V- - 0.5V to V+ + 0.5V
ESD Tolerance
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3kV
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300V
Charged Device Model (CDM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200V
Thermal Resistance (Typical)
JA (°C/W) JC (°C/W)
6 Ld SOT-23 Package (Notes 6, 9) . . . . . . .
170
105
6 Ld UTDFN Package (Notes 7, 8) . . . . . . .
125
80
8 Ld SOIC Package (Notes 6, 9) . . . . . . . . .
110
82
10 Ld MSOP Package (Notes 6, 9) . . . . . . .
175
90
10 Ld UTQFN Package (Notes 6, 9) . . . . . .
190
140
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Ambient Operating Temperature Range . . . . . . . . . . . . . .-40°C to +125°C
Maximum Operating Junction Temperature . . . . . . . . . . . . . . . . . +125°C
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3V to 5.5V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTE:
6. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
7. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
8. For JC, the “case temp” location is the center of the exposed metal pad on the package underside.
9. For JC, the “case temp” location is taken at the package top center.
Electrical Specifications V+ = 5.0V, V- = GND, RL = Open RF = 1kAV = -1unless otherwise specified. Parameters are per amplifier.
Typical values are at V+= 5V, TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to +125°C.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 10)
TYP
MAX
(Note 10)
UNIT
270
630
µV
DC SPECIFICATIONS
VOS
Input Offset Voltage
840
V OS
--------------T
Input Offset Drift vs Temperature
IIO
Input Offset Current
Figure 21
3.1
35
µV/°C
500
nA
900
IB
Input Bias Current
3
6
µA
7
CMIR
Common-Mode Input Range
CMRR
Common-Mode Rejection Ratio
0
VCM = 0V to 3.8V
3.8
V
78
100
dB
PSRR
Power Supply Rejection Ratio
VS = 3V to 5V
74
80
dB
AVOL
Large Signal Voltage Gain
VO = 0.5V to 4V, RL = 1k
90
98
dB
86
VOUT
Maximum Output Voltage Swing
Output low, RL = 1k
20
50
mV
80
Output high, RL = 1kV+ = 5V
4.95
4.97
V
4.92
IS,ON
Supply Current per Amplifier, Enabled
2.6
3.5
mA
3.9
IS,OFF
Supply Current per Amplifier, Disabled
IO+
Short-Circuit Output Current
26
35
µA
48
RL = 10
95
130
mA
90
FN6156 Rev 10.00
July 22, 2014
Page 4 of 18
ISL28191, ISL28291
Electrical Specifications V+ = 5.0V, V- = GND, RL = Open RF = 1kAV = -1unless otherwise specified. Parameters are per amplifier.
Typical values are at V+= 5V, TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to +125°C. (Continued)
PARAMETER
IO-
DESCRIPTION
Short-Circuit Output Current
CONDITIONS
RL = 10
MIN
(Note 10)
TYP
95
130
MAX
(Note 10)
UNIT
mA
90
VSUPPLY
Supply Operating Range
V+ to V-
3
2
5.5
VENH
EN High Level
Referred to V-
VENL
EN Low Level
Referred to V-
IENH
EN Pin Input High Current
VEN = V+
0.8
IENL
EN Pin Input Low Current
VEN = V-
20
V
V
0.8
V
1.1
µA
1.3
80
nA
100
AC SPECIFICATIONS
GBW
-3dB Unity Gain Bandwidth
RF = 0 CL = 20pF, AV = 1, RL = 10k
61
MHz
THD+N
Total Harmonic Distortion + Noise
f = 1kHz. VOUT + 2VP-P, AV = +1, RL = 10k
0.0001
%
HD
(1MHz)
2nd Harmonic Distortion
2VP-P output voltage, AV = 1
-76
dBc
8
-70
dBc
ISO
3rd Harmonic Distortion
Off-state Isolation
fO = 100kHz
AV = +1, VIN = 100mVP-P, RF = 0
CL = 20pF, AV = 1, RL = 10k
-38
dB
X-TALK
ISL28291
Channel-to-Channel Crosstalk
fO = 100kHz
VS = ±2.5V, AV = +1, VIN = 1VP-P,
RF = 0CL = 20pF, AV = 1, RL = 10k
-105
dB
PSRR
Power Supply Rejection Ratio
fO = 100kHz
VS = ±2.5V, AV = +1, VSOURCE = 1VP-P,
RF = 0CL = 20pF, AV = 1, RL = 10k
-70
dB
CMRR
Common Mode Rejection Ratio
fO = 100kHz
VS = ±2.5V, AV = +1, VCM = 1VP-P,
RF = 0CL = 20pF, AV = 1, RL = 10k
-65
dB
en
Input Referred Voltage Noise
fO = 1kHz
1.7
nV/√Hz
in
Input Referred Current Noise
fO = 1kHz
1.8
pA/√Hz
17
V/µs
7
ns
TRANSIENT RESPONSE
SR
Slew Rate
12
12
tr, tf, Small
Signal
Rise Time, tr 10% to 90%
12
ns
AV = 2, VOUT = 1VP-P; RL = 10k
RF /RG = 499499CL = 1.2pF
44
ns
50
ns
AV = 2, VOUT = 4.7VP-P; RL = 10k
RF /RG = 499499CL = 1.2pF
190
ns
190
ns
ENABLE to Output Turn-on Delay Time; AV = 1, VOUT = 1VDC, RL = 10k, CL = 1.2pF
10% EN - 10% VOUT
330
ns
ENABLE to Output Turn-off Delay Time; AV = 1, VOUT = 0VDC, RL = 10k, CL = 1.2pF
10% EN - 10% VOUT
50
ns
tr, tf Large Signal Rise Time, tr 10% to 90%
Fall Time, tf 90% to 10%
Rise Time, tr 10% to 90%
Fall Time, tf 90% to 10%
tEN
AV = 1, VOUT = 0.1VP-P, RL = 10k, CL = 1.2pF
Fall Time, tf 90% to 10%
NOTE:
10. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
FN6156 Rev 10.00
July 22, 2014
Page 5 of 18
ISL28191, ISL28291
Typical Performance Curves
10
3
RL = 100k
2
CLOSED LOOP GAIN (dB)
CLOSED LOOP GAIN (dB)
1
0
-1
-2
RL = 10k
-3
-4
-5
-6
RL = 1k
V+ = 5V
AV = +1
CL = 10pF
VOUT = 10mVP-P
-7
10k
RL = 100
100k
1M
10M
8
CL = 110pF
6
CL = 57pF
4
CL = 57pF
2
CL = 32pF
0
CL = 10pF
-2
-4
-6
-8
-10
10k
100M
100k
FREQUENCY (Hz)
AV = 1000, RF = 499k, RG = 499
VOUT = 100mVP-P
-3
VOUT = 1VP-P
-5
V+ = 5V
AV = +1
RL = 10k
CL = 10pF
-6
-7
-8
10k
40
30
20
AV = 100, RF = 49.9k,
RG = 499
AV = 10, RF = 4.42k, RG = 499
10
0
100k
1M
10M
AV = 1, RF = 0, RG = INF
-10
10k
100M
100k
FREQUENCY (Hz)
1M
10M
100M
FREQUENCY (Hz)
FIGURE 4. FREQUENCY RESPONSE vs CLOSED LOOP GAIN
FIGURE 3. -3dB BANDWIDTH vs VOUT
1M
100k
OUTPUT IMPEDANCE ()
INPUT IMPEDANCE ()
V+ = 5V
RL = 10k
VOUT = 100mVP-P
50
GAIN (dB)
CLOSED LOOP GAIN (dB)
60
0
-4
100M
70
-1
-2
10M
FIGURE 2. GAIN vs FREQUENCY FOR VARIOUS CLOAD
VOUT = 1mVP-P
VOUT = 10mVP-P
1
1M
FREQUENCY (Hz)
FIGURE 1. GAIN vs FREQUENCY FOR VARIOUS RLOAD
2
CL = 20pF
V+ = 5V
AV = +1
RL = 10k
VOUT = 10mVP-P
100k
V+ = 5V, 3V
ENABLED AND
DISABLED
VSOURCE = 1VP-P
10k
1k
100
10k
100k
1M
10M
FREQUENCY (Hz)
FIGURE 5. INPUT IMPEDANCE vs FREQUENCY
FN6156 Rev 10.00
July 22, 2014
100M
10k
V+ = 5V, 3V
VSOURCE = 1VP-P
1k
100
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FIGURE 6. DISABLED OUTPUT IMPEDANCE vs FREQUENCY
Page 6 of 18
ISL28191, ISL28291
Typical Performance Curves (Continued)
100
10
0
-10
VSOURCE = 1V
-20
10
-30
CMRR (dB)
OUTPUT IMPEDANCE ()
V+ = 5V, 3V
VSOURCE = 0.1V
-40
-50
-60
1
V+ = 5V
AV = +1
RL = 10k
CL = 10pF
VOUT = 100mVP-P
-70
-80
0.10
10k
100k
1M
10M
-90
-100
1k
100M
10k
100k
FIGURE 7. ENABLED OUTPUT IMPEDANCE vs FREQUENCY
0
-10
PSRR (dB)
-20
0
V+ = 5V
AV = +1
RL = 10k
CL = 10pF
VOUT = 100mVP-P
-30
-40
PSRR+
-50
-60
PSRR+
PSRR-
-70
-80
-10
VP-P = 1V
-20
VP-P = 10mV
-30
VP-P = 100mV
-40
-50
V+ = 5V
AV = +1
RL = 10k
CL = 10pF
-60
-70
-90
-100
1k
10k
100k
1M
FREQUENCY (Hz)
10M
-80
10k
100M
100k
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 10. OFF ISOLATION vs FREQUENCY
FIGURE 9. PSRR vs FREQUENCY
-30
0.1
V+ = 5V
RL = 10k
-40
RF = 0, AV = 1
VOUT = 2VP-P
400Hz TO 22kHz FILTER
THD + NOISE (%)
-50
CROSSTALK (dB)
100M
FIGURE 8. CMRR vs FREQUENCY
OFF ISOLATION (dB)
10
10M
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
-60
-70
VP-P = 1V
-80
-90
0.01
0.001
-100
-110
-120
10k
100k
1M
10M
FREQUENCY (Hz)
100M
1G
FIGURE 11. CHANNEL TO CHANNEL CROSSTALK vs FREQUENCY
FN6156 Rev 10.00
July 22, 2014
0.0001
0
2k
4k
6k
8k
10k 12k 14k 16k 18k 20k
FREQUENCY (Hz)
FIGURE 12. THD+N vs FREQUENCY
Page 7 of 18
ISL28191, ISL28291
Typical Performance Curves (Continued)
10
V+ = 5V
AV = +1
RL = 10k
FREQUENCY = 1kHz
FILTER = 400Hz TO 22kHz
0.1
INPUT VOLTAGE NOISE (nV/ÖHz)
THD +NOISE (%)
1
0.01
0.001
0.0001
0
0.5
1.0
1.5
2.0
2.5
3.0
1
0.1
3.5
1
10
VOUT (VP-P)
1k
10k
100k
FIGURE 14. INPUT REFERRED NOISE VOLTAGE vs FREQUENCY
FIGURE 13. THD+N @ 1kHz vs VOUT
5
100
10
V+ = 5V
AV = +1
RL = 10k
CL = 10pF
VIN = 1VDC
EN INPUT
4
VOLTS (V)
CURRENT NOISE (pA/Hz)
100
FREQUENCY (Hz)
3
2
ENABLE
DISABLE
ENABLE
1
OUTPUT
1
0.1
1
10
100
1k
10k
0
100k
-1
0
1
FREQUENCY (Hz)
FIGURE 15. INPUT REFERRED NOISE CURRENT vs FREQUENCY
0.08
0.8
0.06
0.6
VOUT
0.4
VIN
VOUT
0.04
0.02
VIN
0
-0.02
V+ = ±2.5V
AV = +1
RL = 10k
VOUT = 100mVP-P
-0.04
-0.06
-0.08
0
20
40
60
80 100 120
TIME (ns)
4
0.2
0
-0.2
V+ = ±2.5V
AV = +2
RF = RG = 499
RL = 10k
VOUT = 1VP-P
-0.4
-0.6
140
160
FIGURE 17. SMALL SIGNAL STEP RESPONSE
FN6156 Rev 10.00
July 22, 2014
3
FIGURE 16. ENABLE/DISABLE TIMING
LARGE SIGNAL (V)
SMALL SIGNAL (V)
2
TIME (µs)
180
200
-0.8
0
100
200
300
400
500
TIME (ns)
600
700
800
FIGURE 18. LARGE SIGNAL (1V) STEP RESPONSE
Page 8 of 18
ISL28191, ISL28291
Typical Performance Curves (Continued)
3
3.5
VOUT
VIN
CURRENT (mA)
LARGE SIGNAL (V)
3.1
1
0
-1
V+ = ±2.5V
AV = +2
RF = RG = 499
RL = 10k
VOUT = 4.7VP-P
-2
-3
0
400
800
1200
TIME (ns)
1600
2.7
2.5
MIN
2.3
2.1
1.5
-40
2000
-20
0
-3.0
MAX
IBIAS+ (µA)
MEDIAN
300
200
100
100
120
MAX
-3.6
MEDIAN
-3.8
-4.0
MIN
-4.2
MIN
0
-4.4
-100
-200
-40
-20
0
20
40
60
80
100
-4.6
-40
120
-20
0
TEMPERATURE (°C)
FIGURE 21. VOS vs TEMPERATURE, VS = ±2.5V
800
n = 100
20
40
60
80
TEMPERATURE (°C)
FIGURE 22. IBIAS+ vs TEMPERATURE, VS = ±2.5V
MAX
n = 100
600
-3.4
MEDIAN
-3.6
400
-3.8
-4.0
IIO (nA)
IBIAS- (µA)
120
-3.4
400
-3.2
100
n = 100
-3.2
500
-3.0
20
40
60
80
TEMPERATURE (°C)
FIGURE 20. SUPPLY CURRENT vs TEMPERATURE,
VS = ±2.5V ENABLED, RL = INF
600
VOS (µV)
MEDIAN
2.9
1.7
n = 100
700
MAX
1.9
FIGURE 19. LARGE SIGNAL (4.7V) STEP RESPONSE
800
n = 100
3.3
2
MIN
-4.2
MEDIAN
200
MAX
0
-4.4
-4.6
-200
-4.8
MIN
-5.0
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
100
FIGURE 23. IBIAS- vs TEMPERATURE, VS = ±2.5V
FN6156 Rev 10.00
July 22, 2014
120
-400
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
100
120
FIGURE 24. IIO vs TEMPERATURE, VS = ±2.5V
Page 9 of 18
ISL28191, ISL28291
Typical Performance Curves (Continued)
160
82
n = 100
150
MAX
130
PSRR (dB)
CMRR (dB)
MAX
80
140
120
110
n = 100
MEDIAN
100
78
MEDIAN
76
MIN
74
90
80
72
MIN
70
-40
-20
0
20
40
60
80
100
70
-40
120
-20
0
60
n = 100
55
4.985
80
100
120
n = 100
45
VOUT (mV)
VOUT (V)
60
50
MAX
4.980
MEDIAN
4.975
4.970
40
MAX
35
30
25
MEDIAN
20
4.965
15
MIN
4.960
-40
40
FIGURE 26. PSRR vs TEMPERATURE ±1.5V TO ±2.5V
FIGURE 25. CMRR vs TEMPERATURE, VCM = 3.8V,
VS = ±2.5V
4.990
20
TEMPERATURE (°C)
TEMPERATURE (°C)
-20
0
20
40
60
80
100
10
-40
120
MIN
-20
0
FIGURE 27. POSITIVE VOUT vs TEMPERATURE, RL = 1k VS = ±2.5V
VCM OVERHEAD TO SUPPLY RAILS (V)
20
40
60
80
100
120
TEMPERATURE (°C)
TEMPERATURE (°C)
FIGURE 28. NEGATIVE VOUT vs TEMPERATURE, RL = 1k
VS = ±2.5V
1.2
1.0
0.8
0.6
0.4
INPUT VOLTAGE TO
THE POSITIVE RAIL (V+ - VCM)
0.2
0
-0.2
-0.4
-0.6
-0.8
-60
INPUT VOLTAGE TO
THE NEGATIVE RAIL (V- + VCM)
-40
-20
0
20 40 60 80
TEMPERATURE (°C)
100 120 140
FIGURE 29. INPUT COMMON MODE VOLTAGE vs TEMPERATURE
FN6156 Rev 10.00
July 22, 2014
Page 10 of 18
ISL28191, ISL28291
Applications Information
Product Description
The ISL28191 and ISL28291 are voltage feedback operational
amplifiers designed for communication and imaging applications
requiring low distortion, very low voltage and current noise. Both
parts feature high bandwidth while drawing moderately low supply
current. They use a classical voltage-feedback topology, which
allows them to be used in a variety of applications where
current-feedback amplifiers are not appropriate because of
restrictions placed upon the feedback element used with the
amplifier.
Using Only One Channel
The ISL28291 is a dual channel op amp. If the application only
requires one channel when using the ISL28291, the user must
configure the unused channel to prevent it from oscillating.
Oscillation can occur if the input and output pins are floating. This
will result in higher than expected supply currents and possible
noise injection into the channel being used. The proper way to
prevent this oscillation is to short the output to the negative input
and ground the positive input (as shown in Figure 31).
+
Enable/Power-Down
The ISL28191 and ISL28291 amplifiers are disabled by applying
a voltage greater than 2V to the EN pin, with respect to the V- pin.
In this condition, the output(s) will be in a high impedance state
and the amplifier(s) current will be reduced to 13µA/Amp. By
disabling the part, multiple parts can be connected together as a
MUX. The outputs are tied together in parallel and a channel can
be selected by the EN pin. The EN pin also has an internal
pull-down. If left open, the EN pin will pull to the negative rail and
the device will be enabled by default.
Input Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. Both parts have
additional back-to-back diodes across the input terminals
(as shown in Figure 30). In pulse applications where the input Slew
Rate exceeds the Slew Rate of the amplifier, the possibility exists
for the input protection diodes to become forward biased. This can
cause excessive input current and distortion at the outputs. If
overdriving the inputs is necessary, the external input current must
never exceed 5mA. An external series resistor may be used to limit
the current, as shown in Figure 30.
R
+
FIGURE 30. LIMITING THE INPUT CURRENT TO LESS THAN 5mA
FN6156 Rev 10.00
July 22, 2014
FIGURE 31. PREVENTING OSCILLATIONS IN UNUSED CHANNELS
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit board
layout is necessary for optimum performance. Low impedance
ground plane construction is essential. Surface mount
components are recommended, but if leaded components are
used, lead lengths should be as short as possible. The power
supply pins must be well bypassed to reduce the risk of
oscillation. The combination of a 4.7µF tantalum capacitor in
parallel with a 0.01µF capacitor has been shown to work well
when placed at each supply pin.
For good AC performance, parasitic capacitance should be kept
to a minimum, especially at the inverting input. When ground
plane construction is used, it should be removed from the area
near the inverting input to minimize any stray capacitance at that
node. Carbon or Metal-Film resistors are acceptable with the
Metal-Film resistors giving slightly less peaking and bandwidth
because of additional series inductance. Use of sockets,
particularly for the SOIC package, should be avoided if possible.
Sockets add parasitic inductance and capacitance, which will
result in additional peaking and overshoot.
Current Limiting
The ISL28191 and ISL28291 have no internal current-limiting
circuitry. If the output is shorted, it is possible to exceed the
Absolute Maximum Rating for output current or power dissipation,
potentially resulting in the destruction of the device. This is why the
output short circuit current is specified and tested with RL = 10.
Page 11 of 18
ISL28191, ISL28291
Power Dissipation
It is possible to exceed the +125°C maximum junction
temperatures under certain load and power-supply conditions. It
is therefore important to calculate the maximum junction
temperature (TJMAX) for all applications to determine if power
supply voltages, load conditions, or package type need to be
modified to remain in the safe operating area. These parameters
are related in Equation 1:
(EQ. 1)
T JMAX = T MAX + JA xPD MAXTOTAL
where:
• PDMAXTOTAL is the sum of the maximum power dissipation of
each amplifier in the package (PDMAX)
• PDMAX for each amplifier can be calculated in Equation 2:
V OUTMAX
PD MAX = 2*V S I SMAX + V S - V OUTMAX ---------------------------R
L
(EQ. 2)
where:
• TMAX = Maximum ambient temperature
• JA = Thermal resistance of the package
• PDMAX = Maximum power dissipation of 1 amplifier
• VS = Supply voltage
• IMAX = Maximum supply current of 1 amplifier
• VOUTMAX = Maximum output voltage swing of the application
• RL = Load resistance
FN6156 Rev 10.00
July 22, 2014
Page 12 of 18
ISL28191, ISL28291
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you
have the latest revision.
DATE
REVISION
CHANGE
July 22, 2014
FN6156.10
Updated location of note references.
Updated Theta JA in the "Thermal Information" table on page 4 and added Theta JC to table.
January 18, 2012
FN6156.9
Page 1 - Ordering Information Update:
Added Eval Board ISL28191EVAL1Z
Changed micro TDFN and TQFN to Ultra matching POD Description
Added SOT-23 Note
Page 10 - Typical Performance Curves:
Added Figure 29 - INPUT COMMON MODE VOLTAGE vs TEMPERATURE
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support
© Copyright Intersil Americas LLC 2006-2013. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN6156 Rev 10.00
July 22, 2014
Page 13 of 18
ISL28191, ISL28291
Package Outline Drawing
P6.064A
6 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE
Rev 0, 2/10
1.90
0-3°
0.95
D
0.08-0.20
A
5
6
4
PIN 1
INDEX AREA
2.80
3
1.60
3
0.15 C D
2x
1
(0.60)
3
2
0.20 C
2x
0.40 ±0.05
B
5
SEE DETAIL X
3
0.20 M C A-B
D
TOP VIEW
2.90
5
END VIEW
10° TYP
(2 PLCS)
0.15 C A-B
2x
H
1.14 ±0.15
C
SIDE VIEW
0.10 C
0.05-0.15
1.45 MAX
SEATING PLANE
DETAIL "X"
(0.25) GAUGE
PLANE
0.45±0.1
4
(0.60)
(1.20)
NOTES:
(2.40)
(0.95)
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to ASME Y14.5M-1994.
3.
Dimension is exclusive of mold flash, protrusions or gate burrs.
4.
Foot length is measured at reference to guage plane.
5.
This dimension is measured at Datum “H”.
6.
Package conforms to JEDEC MO-178AA.
(1.90)
TYPICAL RECOMMENDED LAND PATTERN
FN6156 Rev 10.00
July 22, 2014
Page 14 of 18
ISL28191, ISL28291
Ultra Thin Dual Flat No-Lead Plastic Package (UTDFN)
A
E
6
6 LEAD ULTRA THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE
MILLIMETERS
D
1
3
A1
TOP VIEW
e
1.00 REF
4
6
L
CO.2
D2
SYMBOL
MIN
NOMINAL
MAX
NOTES
A
0.45
0.50
0.55
-
A1
-
-
0.05
-
0.127 REF
A3
0.15 C
3
1
b 6X
0.10 M C A B
E2
0.15
0.20
0.25
-
D
1.55
1.60
1.65
4
D2
0.40
0.45
0.50
-
E
1.55
1.60
1.65
4
E2
0.95
1.00
1.05
-
0.50 BSC
L
0.25
0.30
0.35
Rev. 1 6/06
NOTES:
1. Dimensions are in mm. Angles in degrees.
BOTTOM VIEW
DETAIL A
0.10 C
-
b
e
DAP SIZE 1.30 x 0.76
6X
L6.1.6x1.6A
4
PIN 1
REFERENCE
2X
0.15 C
2X
A
B
2. Coplanarity applies to the exposed pad as well as the terminals.
Coplanarity shall not exceed 0.08mm.
3. Warpage shall not exceed 0.10mm.
4. Package length/package width are considered as special
characteristics.
0.08 C
5. JEDEC Reference MO-229.
A3
SIDE VIEW
C
SEATING
PLANE
6. For additional information, to assist with the PCB Land Pattern
Design effort, see Intersil Technical Brief TB389.
0.127±0.008
0.127 +0.058
-0.008
TERMINAL THICKNESS
A1
DETAIL A
0.25
0.50
1.00
0.45
1.00
2.00
0.30
1.25
LAND PATTERN
FN6156 Rev 10.00
July 22, 2014
6
Page 15 of 18
ISL28191, ISL28291
Package Outline Drawing
M8.15E
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 0, 08/09
4
4.90 ± 0.10
A
DETAIL "A"
0.22 ± 0.03
B
6.0 ± 0.20
3.90 ± 0.10
4
PIN NO.1
ID MARK
5
(0.35) x 45°
4° ± 4°
0.43 ± 0.076
1.27
0.25 M C A B
SIDE VIEW “B”
TOP VIEW
1.75 MAX
1.45 ± 0.1
0.25
GAUGE PLANE
C
SEATING PLANE
0.10 C
0.175 ± 0.075
SIDE VIEW “A
0.63 ±0.23
DETAIL "A"
(1.27)
(0.60)
NOTES:
(1.50)
(5.40)
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Dimension does not include interlead flash or protrusions.
Interlead flash or protrusions shall not exceed 0.25mm per side.
5.
The pin #1 identifier may be either a mold or mark feature.
6.
Reference to JEDEC MS-012.
TYPICAL RECOMMENDED LAND PATTERN
FN6156 Rev 10.00
July 22, 2014
Page 16 of 18
ISL28191, ISL28291
Package Outline Drawing
L10.1.8x1.4A
10 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 6, 8/13
1.80
B
C0.10
IN #1 ID
6
A
1
1
1.40
3
10
0.50
6 PIN 1
INDEX AREA
9 X 0.40
2
10X 0.20 4
0.10 M C A B
0.05 M C
0.70
8
5
0.10
7
2X
4X 0.30
6
6X 0.40
TOP VIEW
BOTTOM VIEW
SEE DETAIL "X"
0.10 C
MAX. 0.55
2.20
1
3
10
(0.70)
SIDE VIEW
1.80
(10X 0.20)
C
SEATING PLANE
0.08 C
8
C
5
(9X 0.60)
6
0.127 REF
7
(6X 0.40)
PACKAGE OUTLINE
0-0.05
TYPICAL RECOMMENDED LAND PATTERN
DETAIL "X"
NOTES:
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to ASME Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Lead width dimension applies to the metallized terminal and is
measured between 0.15mm and 0.30mm from the terminal tip.
5.
JEDEC reference MO-255.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
FN6156 Rev 10.00
July 22, 2014
Page 17 of 18
ISL28191, ISL28291
Package Outline Drawing
M10.118A (JEDEC MO-187-BA)
10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE (MSOP)
Rev 0, 9/09
3.0 ± 0.1
A
0.25
10
DETAIL "X"
CAB
0.18 ± 0.05
SIDE VIEW 2
4.9 ± 0.15
3.0 ± 0.1
1.10 Max
B
PIN# 1 ID
1
2
0.95 BSC
0.5 BSC
TOP VIEW
Gauge
Plane
0.86 ± 0.09
H
0.25
C
3°±3°
SEATING PLANE
0.10 ± 0.05
0.23 +0.07/ -0.08
0.08 C A B
0.55 ± 0.15
0.10 C
DETAIL "X"
SIDE VIEW 1
5.80
4.40
3.00
NOTES:
0.50
0.30
1.
Dimensions are in millimeters.
2.
Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Plastic or metal protrusions of 0.15mm max per side are not
included.
Plastic interlead protrusions of 0.25mm max per side are not
included.
4.
1.40
5.
Dimensions “D” and “E1” are measured at Datum Plane “H”.
TYPICAL RECOMMENDED LAND PATTERN
6.
This replaces existing drawing # MDP0043 MSOP10L.
FN6156 Rev 10.00
July 22, 2014
Page 18 of 18
工商网监
湘ICP备2023018690号
