ISL43231IR

ISL43231 ® Data Sheet February 27, 2006 Low-Voltage, Single and Dual Supply, Triple SPDT Analog Switch Features The Intersil ISL43231 device is a precision, bidirectional, analog switch configured as a a triple single pole/double throw (SPDT) switch, designed to operate from a single +2V to +12V supply or from a ±2V to ±6V supply. The device has an inhibit and inhibit bar pin to simultaneously open all signal paths. The device also has a latch bar pin to lock in the last switch address. ON resistance of 39Ω with a ±5V supply and 125Ω with a +3.3V supply. Each switch can handle rail to rail analog signals. The off-leakage current is only 0.1nA at +25°C or 2.5nA at +85°C. All digital inputs have 0.8V to 2.4V logic thresholds, ensuring TTL/CMOS logic compatibility when using a single +3.3V or +5V supply or dual ±5V supplies. The ISL43231 is a committed triple SPDT, which is perfect for use in 2-to-1 multiplexer applications. Table 1 summarizes the performance of this part. TABLE 1. FEATURES AT A GLANCE CONFIGURATION TRIPLE SPDT ±5V RON 39Ω ±5V tON/tOFF 32ns/18ns 12V RON 32Ω 12V tON/tOFF 23ns/15ns 5V RON 65Ω 5V tON/tOFF 38ns/19ns 3.3V RON 125Ω 3.3V tON/tOFF 70ns/32ns Package 20 Ld 4x4 QFN FN6054.2 • Fully Specified at 3.3V, 5V, ±5V, and 12V Supplies for 10% Tolerances • ON Resistance (RON) Max, VS = ±4.5V. . . . . . . . . . . 50Ω • ON Resistance (RON) Max, VS = +3V . . . . . . . . . . . 155Ω • RON Matching Between Channels, VS = ±5V. . . . . . . . . 2.5kV Thermal Resistance (Typical, Note 2) θJA (°C/W) 20 Ld 4x4 QFN Package . . . . . . . . . . . . . . . . . . . . . 45 Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C (Lead Tips Only) Operating Conditions Temperature Range ISL43231IR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Signals on NC, NO, COM, ADD, EN, EN, or LE exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to maximum current ratings. 2. θJA is measured with the component mounted on a high effective thermal conductivity test board with direct die attach features. See Tech Brief TB379 for details. Electrical Specifications ±5V SupplyTest Conditions: VSUPPLY = ±4.5V to ±5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 3), Unless Otherwise Specified TEMP (°C) (NOTE 4) MIN TYP Full V- - V+ V 25 - 44 50 Ω Full - - 80 Ω 25 - 1.3 4 Ω Full - - 6 Ω 25 - 7.5 9 Ω Full - - 12 Ω 25 -0.1 0.002 0.1 nA Full -2.5 - 2.5 nA 25 -0.1 0.002 0.1 nA Full -2.5 - 2.5 nA 25 -0.1 0.002 0.1 nA Full -2.5 - 2.5 nA Input Voltage High, VINH, VADDH Full 2.4 - - V Input Voltage Low, VINL, VADDL Full - - 0.8 V PARAMETER TEST CONDITIONS (NOTE 4) MAX UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG VS = ±4.5V, ICOM = 2mA, VNO or VNC = 3V (See Figure 6) ON Resistance, RON RON Matching Between Channels, ∆RON VS = ±4.5V, ICOM = 2mA, VNO or VNC = 3V (Note 5) RON Flatness, RFLAT(ON) VS = ±4.5V, ICOM = 2mA, VNO or VNC = ±3V, 0V (Note 6) NO or NC OFF Leakage Current, INO(OFF) or INC(OFF) VS = ±5.5V, VCOM = ±4.5V, VNO or VNC = +4.5V (Note 7) COM OFF Leakage Current, ICOM(OFF) VS = ±5.5V, VCOM = ±4.5V, VNO or VNC = +4.5V (Note 7) COM ON Leakage Current, ICOM(ON) VS = ±5.5V, VCOM = VNO or VNC = ±4.5V (Note 7) DIGITAL INPUT CHARACTERISTICS Input Current, IADDH, IADDL, IENH, IENL VS = ±5.5V, VINH, VADD = 0V or V+ Full -0.5 - 0.5 µA Input Current, IENH, ILEH VS = ±5.5V, VINH, VADD = 0V or V+ Full -1.5 - 1.5 µA Input Current, IENL, ILEL VS = ±5.5V, VINH, VADD = 0V or V+ Full -4 - 4 µA 3 FN6054.2 February 27, 2006 ISL43231 Electrical Specifications ±5V SupplyTest Conditions: VSUPPLY = ±4.5V to ±5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 3), Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS TEMP (°C) (NOTE 4) MIN TYP (NOTE 4) MAX UNITS 25 - 35 50 ns Full - - 60 ns 25 - 22 35 ns Full - - 40 ns 25 - 43 60 ns Full - - 70 ns DYNAMIC CHARACTERISTICS VS = ±4.5V, VNO or VNC = ±3V, RL =300Ω, CL = 35pF, VIN = 0 to 3 (See Figure 1) Enable Turn-ON Time, tON VS = ±4.5V, VNO or VNC = ±3V, RL =300Ω, CL = 35pF, VIN = 0 to 3 (See Figure 1) Enable Turn-OFF Time, tOFF Address Transition Time, tTRANS VS = ±4.5V, VNO or VNC = ±3V, RL =300Ω, CL = 35pF, VIN = 0 to 3 (See Figure 1) Break-Before-Make Time, tBBM VS = ±5.5V, VNO or VNC = 3V, RL = 300Ω, CL = 35pF, VIN = 0 to 3V (See Figure 3) Full 2 7 - ns Latch Setup Time, tS (See Figure 4) 25 25 - - ns Full 35 - - ns 25 0 - - ns Full 0 - - ns 25 15 - - ns Full 25 - - ns Latch Hold Time, tH (See Figure 4) Latch Pulse Width, tWPW (See Figure 4) Charge Injection, Q CL = 1.0nF, VG = 0V, RG = 0Ω (See Figure 2) 25 - 0.3 1 pC NO/NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 8) 25 - 3 - pF COM OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 8) 25 - 9 - pF COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 8) 25 - 14 - pF OFF Isolation RL = 50Ω, CL = 15pF, f = 100kHz, VNOx or VNCx = 1VRMS (See Figures 5, 7 and 20) 25 - 92 - dB 25 -