RWP06040-10

Wideband Power Amplifier Product Features GaN on SiC Broadband High Power Amplifier 450 to 880MHz Operation Bandwidth Small Signal Gain 38dB min 40W Typical. P3dB RWP06040-10 Application UHF Television Package : DP-75 Description The RWP06040-10 is designed for Wideband Power Amplifier application frequencies from 450 to 880MHz. This module uses GaN HEMT technology which performs high breakdown voltage, high linearity, wide bandwidth and high efficiency. Gallium Nitride on SiC technology is used and attached on an aluminum sub carrier. Full in/out matching for broadband performance is already applied. Improved thermal handling by patented technology. Typical Specifications No 1 2 3 4 5 6 7 8 Bandwidth Small Signal Gain Gain Variation vs Temperature Gain Variation vs Frequency P3dB OIP3 @ Po = +33dBm (1MHz Tone spacing, CW 2Tone) Input Return Loss Output Return Loss △=5MHz ACLR@Pout=28dBm W-CDMA,64PCH,4FA Spectrum Analyzer Setting : RBW=30KHz, VBW=10KHz 450MHz △=10MHz △=5MHz 880MHz △=10MHz 10 11 12 Supply voltage Quiescent Current consumption On/Off Switch Time Shut Down or Switch On/Off TTL Voltage On: TTL "Low" Off: TTL "High"(300mA@Disable) On : TTL “Low”(Enable) Off : TTL “High” Vcc(=Vds) 450MHz to 880MHz 450MHz to 880MHz -20°C to 60°C Item Conditions VCC = +28V; T = 25℃; ZS = ZL = 50Ω Min 450 38 -2.0 ±1 44 49 45 51 -12 -11 45 48 44 47 27.5 48 51 dBc 45 48 28 2.5 3.0 0 2.5 5 30 2.7 5.0 0.5 V 5.5 V A uS -10 -7 40 Typ Max 880 42 +2.0 ±2 Unit MHz dB dB dBpp dBm dBm dB dB 9 13 ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier Environmental Characteristics No 1 2 3 Operating Temperature Storage Temperature Vibration Item RWP06040-10 Min -20 -40 Typ Max +60 +105 Unit °C °C MIL-STD-810G Method 514.6 ANNEX C Absolute Maximum Ratings No 1 2 3 4 Input RF Power Supply Voltage Load Mismatch Value Item Operating Flange Temperature Rating +85 +12 +30 3 : 1 @ all load phase Unit °C dBm V * Input Signal Condition : CW 1-Tone Ordering Information No 1 2 RWP06040-10 RWP06040-1H Part Number Pallet Module assembled with RWP06040-10 Package * RWP06040-1H is a SMA connectorized housing version of RWP06040-10. Electrical parameters are all same as RWP06040-10. For more information, please contact RFHIC. ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier RWP06040-10 Typical Performance @ 25℃ Frequency (MHz) 450MHz 550MHz 650MHz 750MHz 880MHz P1dB (dBm) 44.4 42.5 42.5 43.0 43.1 P3dB (dBm) 45.6 44.9 44.9 45.4 45.4 Current @P1dB (A) 2.3 2.4 2.4 2.5 2.5 Current @P3dB (A) 2.4 3.1 3.2 3.0 3.0 RWP06040-10 OIP3 (30dBm/Tone) (dBm) 51.6 50.8 50.2 50.5 50.3 W-CDMA 64CH 4FA @ 28dBm -5MHZ (dBc) -48.0 -46.3 -45.4 -45.7 -45.5 +5MHZ (dBc) -48.1 -46.4 -45.7 -46.1 -46.0 -10MHZ (dBc) -50.8 -49.1 -48.1 -48.4 -48.2 +10MHZ (dBc) -51.0 -49.3 -48.6 -48.9 -48.8 Gain 45 40 Input Return Loss 0 -5 35 -10 M A G (dB ) MAG(dB) 30 25 20 -15 -20 15 10 10 440 850 FREQ(MHz) 1300 1700 -25 -30 10 440 850 FREQ(M Hz) 1300 1700 P3 48.0 47.0 46.0 P3 (dBm) 45.0 44.0 43.0 42.0 41.0 40.0 450MHz 650MHz Freq (MHz) 880MHz OIP3 59.0 57.0 OIP3 (dBm) 55.0 53.0 51.0 49.0 47.0 45.0 450M z H 650M z H Freq (M z) H 880M z H ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier RWP06040-10 W-CDMA, 64PCH, 4FA ACLR, PAPR 11.3dB ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier RWP06040-10 Precautions 1. This product is designed to be used for broadband amplification. Heat generation is higher when there is no RF signal in the device. Therefore, the worst case scenario is when there is no RF signal, and the amplifier is “on” with current draw. The temperature must be calculated properly. Case temperature must maintain below 85°C. Right side drawing notes how to use a temperature monitoring function to protect against overheating. 2. Thermal Grease or Metal Thermal Interface Materials are recommended for heat dissipation. An example would be spreading thermal grease on the bottom of the device. Comparator Block (with hysteresis gap) + Ref Voltage +Vcc RF IN RF OUT Vcc(+28V) Shut Down (+5V) Temp Monitor Switch ON/OFF ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier Package Dimensions (Type: DP-75) (Unit : mm/[inch], Tolerance : ±0.2/[.008]) RWP06040-10 How to connect the amplifier to a target PCB Method-І (with Pin) Method-ΙІ (without Pin) - If you cut out the pin Pin Description Pin No 1 2 3 4 5 6 RF IN Vcc (+28V) Shut Down (+5V) Switch ON/OFF Temp Monitor RF OUT Port Name RF Input DC Supply Shut Down @ TTL High, Enable @ TTL Low Disable @ TTL High (Switch Status : Off) 0.85V @ 25℃, Scale : 10mV/℃ (Accuracy : ±3℃) RF Output Function * Terminal Pin Information : ASK206091,AA (Acethink, Pin) , ASK20556,AA-1(Acethink, Pin Socket) * Recommended Screw Torque : 8.0kgf.cm±1 using SEMS M3 10mm Bolt ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1 Wideband Power Amplifier Note : RWP06040-10 RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5078 ▪ www.rfhic.com/contact ▪ All specifications may change without notice. ▪ Version 1.1