BA2904YFVM-C

Operational Amplifier / Comparator Series Automotive Operational Amplifiers: Ground Sense BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C No.11049EBT23 ●Description Automotive series BA2904Y family and BA2902Y family integrate two or four independent Op-Amps and phase compensation capacitors on a single chip and have some features of high-gain, low power consumption, and operating voltage range of 3[V] to 32[V] (single power supply ). ●Features 1) Operable with a single power supply 2) Wide operating supply voltage +3.0[V]～+32.0[V]( single supply) 3) Standard Op-Amp Pin-assignments 4) Input and output are operable GND sense 5) Internal phase compensation type 6) Low supply current 7) High open loop voltage gain 8) Internal ESD protection Human body model (HBM) ±5000[V](Typ.) 9) Wide temperature range -40[℃]～+125[℃] ●Pin Assignment OUT1 OUT1 1 CH1 1 2 3 4 5 6 7 CH2 CH3 CH1 CH4 14 13 12 11 10 9 8 Automotive series Dual Quad BA2904Y family BA2902Y family OUT4 -IN4 +IN4 VEE +IN3 - IN3 OUT3 8 VCC -IN1 +IN1 - IN1 2 7 OUT2 VCC +IN1 3 CH2 6 - IN2 +IN2 - IN2 VEE 4 5 + IN2 OUT2 SOP8 MSOP8 SOP14 SSOP-B14 BA2904YF-C BA2904YFVM-C BA2902YF-C BA2902YFV-C www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C ●Absolute Maximum Ratings (Ta=25[℃]) ○BA2904Y family , BA2902Y family Parameter Supply Voltage Differential Input Voltage (*1) Input Common-mode Voltage Range Operating Temperature Range Storage Temperature Range Maximum Junction Temperature Symbol VCC-VEE Vid Vicm Topr Tstg Tjmax Ratings BA2904Y, BA2902Y +36 36 (VEE-0.3)～(VEE+36) -40～+125 -55～+150 +150 Technical Note Unit V V V ℃ ℃ ℃ Note: Absolute maximum rating item indicates the condition which must not be exceeded. Application if voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics. (*1) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C ●Electric Characteristics ○BA2904Y family (Unless otherwise specified VCC=+5[V], VEE=0[V]) Limits Temperature Parameter Symbol Range Min. Typ. Input Offset Voltage (*2) 25℃ Vio Full range 25℃ Iio Full range 25℃ Ib Full range 25℃ Supply Current ICC Full range 25℃ High Level Output Voltage VOH Full range 3.5 3.2 27 28 5 1.2 20 mV V 0.7 100 1.2 mA 20 100 60 nA 2 7 50 nA 2 Technical Note Max. 7 Unit Conditions VOUT=1.4[V] mV VCC=5～30[V], VOUT=1.4[V] VOUT=1.4[V] Input Offset Current (*2) Input Bias Current (*2) VOUT=1.4[V] RL=∞All Op-Amps RL=2[kΩ] VCC=30[V],RL=10[kΩ] RL=∞All Op-Amps Low Level Output Voltage VOL Full range 25℃ Large Signal Voltage Gain AV Full range Input Common-mode Voltage range 25℃ Vicm Full range 25 25 0 0 100 - V/mV VCC-1.5 V VCC-2.0 RL≧2[kΩ],VCC=15[V] VOUT=1.4～11.4[V] (VCC-VEE)=5V, VOUT=VEE+1.4[V] Common-mode Rejection Ratio CMRR 25℃ 65 80 - dB VOUT=1.4[V] Power Supply Rejection Ratio PSRR 25℃ 65 100 - dB VCC=5~30[V] Output Source Current (*3) 25℃ IOH Full range IOL Isink 25℃ Full range 25℃ 20 10 10 2 12 30 20 40 mV mA μA VIN+=1[V],VIN-=0[V] VOUT=0[V] 1CH is short circuit VIN+=0[V],VIN-=1[V] VOUT=5[V] 1CH is short circuit VIN+=0[V],VIN-=1[V] VOUT=200[mV] Output Source Current (*3) (*2) (*3) Absolute value Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C Technical Note ○BA2902Y family (Unless otherwise specified VCC=+5[V], VEE=0[V]) Limits Temperature Parameter Symbol Range Min. Typ. Input Offset Voltage (*4) 25℃ Vio Full range 25℃ Iio Full range 25℃ Ib Full range 25℃ Supply Current ICC Full range 25℃ High Level Output Voltage VOH Full range 3.5 3.2 27 28 5 0.7 20 2 2 Max. 7 Unit Conditions VOUT=1.4[V] mV 7 50 nA 100 60 nA 100 2 mA 3 20 mV V VCC=5～30[V], VOUT=1.4[V] VOUT=1.4[V] Input Offset Current (*4) Input Bias Current (*4) VOUT=1.4[V] RL=∞ All Op-Amps RL=2[kΩ] VCC=30[V],RL=10[kΩ] RL=∞All Op-Amps Low Level Output Voltage VOL Full range 25℃ Large Signal Voltage Gain AV Full range Input Common-mode Voltage range 25℃ Vicm Full range 25 25 0 0 100 - V/mV VCC-1.5 V VCC-2.0 RL≧2[kΩ],VCC=15[V] VOUT=1.4～11.4[V] (VCC-VEE)=5V, VOUT=VEE+1.4[V] Common-mode Rejection Ratio CMRR 25℃ 65 80 - dB VOUT=1.4[V] Power Supply Rejection Ratio PSRR 25℃ 65 100 - dB VCC=5~30[V] Output Source Current (*5) 25℃ IOH Full range IOL Isink 25℃ Full range 25℃ 20 10 10 2 12 30 20 40 mV mA μA VIN+=1[V],VIN-=0[V] VOUT=0[V] 1CH is short circuit VIN+=0[V],VIN-=1[V] VOUT=5[V] 1CH is short circuit VIN+=0[V],VIN-=1[V] VOUT=200[mV] Output Source Current (*5) (*4) (*5) Absolute value Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C ●Reference Data 1000 Technical Note BA2904Y family BA2904Y family 1.0 BA2904Y family 1.0 BA2904Y family POWER DISSIPATION [mW] SUPPLY CURRENT [mA] 800 BA2904YF-C 0.8 25℃ －40℃ SUPPLY CURRENT [mA] 0.8 32V 600 BA2904YFVM-C 0.6 0.6 400 0.4 125℃ 0.4 5V 3V 200 0.2 0.2 0 0 25 50 75 100 125 150 0.0 0 10 20 30 40 0.0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [ ℃] SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] Fig. 1 Derating Curve MAXIMUM OUTPUT VOLTAGE [V] . 40 Fig. 2 Supply Current – Supply Voltage MAXIMUM OUTPUT VOLTAGE [V] . OUTPUT SOURCE CURRENT [mA] 5 BA2904Y family Fig. 3 Supply Current – Ambient Temperature 50 -40℃ BA2904Y family BA2904Y family -40℃ 30 125℃ 4 40 25℃ 3 30 20 25℃ 2 20 125℃ 10 1 10 0 0 10 20 30 40 0 -50 -25 0 0 1 2 3 4 5 0 25 50 75 100 125 150 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] OUTPUT VOLTAGE [V] Fig. 4 Maximum Output Voltage – Supply Voltage (RL=10[kΩ]) Fig. 5 Maximum Output Voltage – Ambient Temperature (VCC=5[V],RL=2[kΩ]) Fig. 6 Output Source Current – Output Voltage (VCC=5[V]) OUTPUT SOURCE CURRENT [mA] OUTPUT SINK CURRENT [mA] 50 BA2904Y family 100 BA2904Y family 30 BA2904Y family 15V 40 3V 5V 10 125℃ -40℃ OUTPUT SINK CURRENT [mA] 30 15V 1 20 5V 3V 20 0.1 25℃ 10 10 0.01 0 -50 -25 0.001 0 25 50 75 100 125 150 0 0.4 0.8 1.2 1.6 2 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [ ℃] OUTPUT VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] Fig. 7 Output Source Current – Ambient Temperature (VOUT=0[V]) 80 70 60 50 40 30 20 10 0 0 5 10 15 20 25 30 35 125℃ 25℃ BA2904Y family Fig. 8 Output Sink Current – Output Voltage (VCC=5[V]) 80 BA2904Y family Fig. 9 Output Sink Current – Ambient Temperature (VOUT=VCC) 8 BA2904Y family LOW-LEVEL SINK CURRENT [ μA] LOW-LEVEL SINK CURRENT [ μA] INPUT OFFSET VOLTAGE [mV] -40℃ 32V 70 60 50 40 30 20 10 0 -50 -25 3V 5V 6 4 2 0 -2 125℃ -40℃ 25℃ -4 -6 -8 0 25 50 75 100 125 150 0 5 10 15 20 25 30 35 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] Fig. 10 Low Level Sink Current – Supply Voltage (VOUT=0.2[V]) Fig. 11 Low Level Sink Current – Ambient Temperature (VOUT=0.2[V]) Fig. 12 Input Offset Voltage – Supply Voltage (Vicm=0[V], VOUT=1.4[V]) SUPPLY VOLTAGE [V] (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 5/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C 8 BA2904Y family Technical Note 50 BA2904Y family 50 BA2904Y family INPUT OFFSET VOLTAGE [mV] INPUT BIAS CURRENT [nA] 4 2 0 -2 -4 -6 -8 -50 -25 5V 32V 3V 40 -40℃ 25℃ INPUT BIAS CURRENT [nA] 6 40 32V 30 30 20 20 3V 5V 10 125℃ 10 0 0 25 50 75 100 125 150 0 5 10 15 20 25 30 35 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [ ℃] SUPPLY VOLTAGE [V] Fig. 13 Input Offset Voltage – Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) BA2904Y family Fig. 14 Input Bias Current – Supply Voltage (Vicm=0[V], VOUT=1.4[V]) 8 BA2904Y family Fig. 15 Input Bias Current – Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) BA2904Y family AMBIENT TEMPERATURE [ ℃] 50 10 INPUT BIAS CURRENT [nA] 40 30 20 10 0 -10 -50 -25 6 4 2 0 -2 -4 -6 -8 -40℃ 25℃ 125℃ INPUT OFFSET CURRENT [nA] INPUT OFFSET VOLTAGE [mV] 5 -40℃ 25℃ 0 125℃ -5 -10 -1 0 1 2 3 4 5 0 5 10 15 20 25 30 35 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [ ℃] INPUT VOLTAGE [Vin] Supply Voltage [V] Fig. 16 Input Bias Current – Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) 10 BA2904Y family Fig.17 Input Offset Voltage – Input Voltage (VCC=5[V]) Fig. 18 Input Offset Current – Supply Voltage (Vicm=0[V],VOUT=1.4[V]) BA2904Y family LARGE SIGNAL VOLTAGE GAIN [dB] ... 130 -40℃ 25℃ LARGE SIGNAL VOLTAGE GAIN [dB] . 140 140 130 120 110 100 90 80 70 60 -50 5V 15V BA2904Y family INPUT OFFSET CURRENT [nA] 5 3V 120 110 100 90 80 70 60 4 6 8 10 12 14 16 125℃ 0 5V 32V -5 -10 -50 -25 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150 Fig. 19 Input Offset Current – Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) 140 BA2904Y family AMBIENT TEMPERATURE [ ℃] Fig. 20 Large Signal Voltage Gain – Supply Voltage(RL=2[kΩ]) COMMON MODE REJECTION RATIO [dB] 140 32V BA2904Y family SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] Fig. 21 Large Signal Voltage Gain – Ambient Temperature (RL=2[kΩ]) POWER SUPPLY REJECTION RATIO [dB] 140 130 120 110 100 90 80 70 60 -50 -25 BA2904Y family COMMON MODE REJECTION RATIO [dB] 120 -40℃ 25℃ 120 100 125℃ 100 80 80 5V 3V 60 60 40 0 10 20 30 40 40 -50 -25 0 25 50 75 100 125 150 0 25 50 75 100 125 150 Fig. 22 Common Mode Rejection Ratio – Supply Voltage SUPPLY VOLTAGE [V] Fig. 23 Common Mode Rejection Ratio – Ambient Temperature AMBIENT TEMPERATURE [ ℃] Fig. 24 Power Supply Rejection Ratio – Ambient Temperature AMBIENT TEMPERATURE [ ℃] (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C ● Reference Data 1000 Technical Note BA2902Y family BA2902Y family BA2902YFV-C 2.0 BA2902Y family 2.0 BA2902Y family POWER DISSIPATION [mW] SUPPLY CURRENT [m A] 800 BA2902YF-C 1.6 25℃ －40℃ SUPPLY CURRENT [mA] 1.6 600 1.2 1.2 32V 400 0.8 125℃ 0.8 5V 3V 200 0.4 0.4 0 0 25 50 75 100 125 150 0.0 0.0 AMBIENT TEMPERATURE [ ℃] 0 Fig. 25 Derating Curve MAXIMUM OUTPUT VOLTAGE [V] . 40 Fig. 26 Supply Current – Supply Voltage MAXIMUM OUTPUT VOLTAGE [V] . OUTPUT SOURCE CURRENT [mA] 5 BA2902Y family 10 20 30 SUPPLY VOLTAGE [V] 40 -50 0 50 100 150 AMBIENT TEMPERATURE [ ℃] Fig. 27 Supply Current – Ambient Temperature 50 -40℃ BA2902Y family BA2902Y family 30 -40℃ 4 40 25℃ 3 30 20 100℃ 25℃ 2 20 125℃ 10 1 10 0 0 10 20 30 40 0 -50 -25 0 0 1 2 3 4 5 0 25 50 75 100 125 150 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] OUTPUT VOLTAGE [V] Fig. 28 Maximum Output Voltage – Supply Voltage (RL=10[kΩ]) Fig. 29 Maximum Output Voltage – Ambient Temperature (VCC=5[V],RL=2[kΩ]) Fig. 30 Output Source Current – Output Voltage (VCC=5[V]) OUTPUT SOURCE CURRENT [mA] OUTPUT SINK CURRENT [mA] 50 BA2902Y family 100 BA2902Y family 30 BA2902Y family 15V 40 3V 10 125℃ OUTPUT SINK CURRENT [mA] 30 15V 5V 1 -40℃ 20 5V 3V 20 0.1 25℃ 10 10 0.01 0 -50 -25 0.001 0 25 50 75 100 125 150 0 0.4 0.8 1.2 1.6 2 0 -50 -25 0 25 50 75 100 125 150 Fig. 31 Output Source Current – Ambient Temperature (VOUT=0[V]) 80 70 60 50 40 125℃ 25℃ -40℃ BA2902Y family AMBIENT TEMPERATURE [ ℃] OUTPUT VOLTAGE [V] Fig. 32 Output Sink Current – Output Voltage (VCC=5[V]) 80 BA2902Y family 32V Fig. 33 Output Sink Current – Ambient Temperature (VOUT=VCC) 8 BA2902Y family AMBIENT TEMPERATURE [ ℃] LOW-LEVEL SINK CURRENT [ μA] LOW-LEVEL SINK CURRENT [ μA] INPUT OFFSET VOLTAGE [mV] 70 60 50 40 30 20 10 0 -50 -25 5V 6 4 2 0 -2 125℃ -40℃ 25℃ 30 20 10 0 0 5 10 15 20 25 30 35 3V -4 -6 -8 0 25 50 75 100 125 150 0 5 10 15 20 25 30 35 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] SUPPLY VOLTAGE [V] Fig. 34 Low Level Sink Current – Supply Voltage (VOUT=0.2[V]) Fig. 35 Low Level Sink Current – Ambient Temperature (VOUT=0.2[V]) Fig. 36 Input Offset Voltage – Supply Voltage (Vicm=0[V], VOUT=1.4[V]) (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 7/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C 8 BA2902Y family Technical Note 50 BA2902Y family 50 BA2902Y family INPUT OFFSET VOLTAGE [mV] INPUT BIAS CURRENT [nA] 4 2 0 -2 -4 -6 -8 -50 -25 5V 32V 3V 40 -40℃ INPUT BIAS CURRENT [nA] 6 40 32V 30 30 20 25℃ 125℃ 20 3V 10 10 5V 0 0 25 50 75 100 125 150 0 5 10 15 20 25 30 35 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [ ℃] SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] Fig. 37 Input Offset Voltage – Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) 50 BA2902Y family Fig. 38 Input Bias Current – Supply Voltage (Vicm=0[V], VOUT=1.4[V]) 8 BA2902Y family -40℃ 25℃ 125℃ Fig. 39 Input Bias Current – Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) 10 BA2902Y family INPUT BIAS CURRENT [nA] 40 30 20 10 0 -10 -50 -25 6 4 2 0 -2 -4 -6 -8 INPUT OFFSET CURRENT [nA] INPUT OFFSET VOLTAGE [mV] 5 -40℃ 25℃ 0 125℃ -5 -10 -1 0 1 2 3 4 5 0 5 10 15 20 25 30 35 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [ ℃] INPUT VOLTAGE [Vin] SUPPLY VOLTAGE [V] Fig. 40 Input Bias Current – Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) Fig. 41 Input Offset Voltage – Input Voltage (VCC=5[V]) Fig. 42 Input Offset Current – Supply Voltage (Vicm=0[V],VOUT=1.4[V]) LARGE SIGNAL VOLTAGE GAIN [dB] ... 130 120 110 100 90 80 70 60 4 6 8 -40℃ 25℃ LARGE SIGNAL VOLTAGE GAIN [dB] . 10 BA2902Y family 140 BA2902Y family 140 130 120 110 100 90 80 70 60 -50 5V BA2902Y family INPUT OFFSET CURRENT [nA] 15V 5 3V 0 5V 32V 125℃ -5 -10 -50 -25 0 25 50 75 100 125 150 10 12 14 16 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [ ℃] SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] Fig. 43 Input Offset Current – Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) 140 BA2902Y family Fig. 44 Large Signal Voltage Gain – Supply Voltage (RL=2[kΩ]) 140 32V BA2902Y family Fig. 45 Large Signal Voltage Gain – Ambient Temperature (RL=2[kΩ]) 140 130 120 110 100 90 80 70 60 -50 -25 BA2902Y family COMMON MODE REJECTION RATIO [dB] COMMON MODE REJECTION RATIO [dB] 120 -40℃ 25℃ 120 100 125℃ 100 80 80 5V 3V 60 60 40 0 10 20 30 40 40 -50 -25 0 25 50 75 100 125 150 POWER SUPPLY REJECTION RATIO [dB] 0 25 50 75 100 125 150 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [ ℃] AMBIENT TEMPERATURE [ ℃] Fig. 46 Common Mode Rejection Ratio – Supply Voltage Fig. 47 Common Mode Rejection Ratio – Ambient Temperature Fig. 48 Power Supply Rejection Ratio – Ambient Temperature (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C ●Circuit Diagram VCC Technical Note －IN ＋IN VOUT VEE BA2904Y / BA2902Y Schematic Diagram Fig. 49 Schematic Diagram (one channel only) ●Test circuit1 NULL method VCC,VEE,EK,Vicm Unit：[V] BA2904Y family BA2902Y family Vcc Input Offset Voltage Input Offset Current Input Bias Current Large Signal Voltage Gain Common-mode Rejection Ratio (Input common-mode Voltage Range) Power Supply Rejection Ratio - Calculation 1. Input Offset Voltage (Vio) Vio = | VF1 | 1 + Rf / Rs [V] C2 0.1[μF] Parameter VF S1 S2 S3 calculation Vicm 0 0 0 0 0 0 3.5 0 0 1 2 3 4 5 6 VEE 0 0 0 0 0 0 0 0 0 EK -1.4 -1.4 -1.4 -1.4 -11.4 -1.4 -1.4 -1.4 -1.4 VF1 VF2 VF3 VF4 VF5 VF6 VF7 VF8 VF9 VF10 ON OFF OFF ON ON ON ON ON OFF ON OFF ON ON ON OFF OFF OFF ON OFF OFF 5～30 5 5 15 15 5 5 5 30 2. Input Offset Current (Iio) Iio = | VF2－VF1 | Ri ×(1 + Rf / Rs) [A] 3. Input Bias Current (Ib) Ib = | VF4－VF3 | 2×Ri× (1 + Rf / Rs) S1 Rf 50[kΩ] RK VCC 500[kΩ] C1 0.1[μF] +15[V] [A] Rs 50[Ω] 50[Ω] Ri 10[kΩ] 10[kΩ] Ri S2 EK 4. Large Signal Voltage Gain (Av) Av = 20×Log ΔEK×(1+Rf /Rs) |VF5-VF6| [dB] Vic m DUT S3 VEE RK 500[kΩ] NULL C3 1000[pF] Rs 5. Common-mode Rejection Ration (CMRR) CMRR = 20×Log ΔVicm×(1+Rf /Rs) |VF8-VF7| [dB] RL -15[V] V VF 6. Power supply rejection ratio (PSRR) PSRR = 20×Log ΔVcc×(1+Rf /Rs) |VF10-VF9| [dB] Fig. 50 Test circuit1 (one channel only) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 9/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C ●Test Circuit 2 Switch Condition SW 1 SW 2 SW 3 SW 4 SW 5 SW 6 SW 7 SW 8 SW 9 SW 10 SW 11 Technical Note SW No. Supply Current High Level Output Voltage Low Level Output Voltage Output Source Current Output Sink Current Slew Rate Gain Bandwidth Product Equivalent Input Noise Voltage SW 12 SW 13 SW 14 OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF ON OFF OFF OFF ON OFF ON OFF OFF ON ON OFF OFF OFF ON ON ON OFF OFF OFF OFF ON OFF OFF OFF OFF ON OFF OFF ON ON OFF OFF OFF OFF ON OFF OFF OFF Input voltage SW4 SW5 R2 VH VCC A VL － Output voltage SW1 SW2 SW3 SW6 RS R1 SW7 SW8 VEE Input wave SR=ΔV/Δt t ＋ SW9 SW10 SW11 SW12 SW13 SW14 VH A ～ VIN- VIN+ ～ RL CL V ～ V VOU T ΔV VL Δt Output wave t Fig. 51 Test Circuit 2 (each Op-Amp) Fig. 52 Slew Rate Input Waveform ●Measurement Circuit 3 Amplifier To Amplifier Coupling VCC VCC R1//R2 R1//R2 OTHER CH VEE R1 VIN R2 R1 R2 VEE V VOUT1 40dB amplifier =0.5[Vrms] V VOUT2 40dB amplifier 100×VOUT1 VOUT2 CS＝20×log Fig. 53 Test Circuit 3 www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 10/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C Technical Note ●Derating curves Power dissipation(total loss) indicates the power that can be consumed by IC at Ta=25℃(normal temperature). IC is heated when it consumed power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that can be accepted by IC chip depends on circuit configuration, manufacturing process, and consumable power is limited. Power dissipation is determined by the temperature allowed in IC chip(maximum junction temperature) and thermal resistance of package(heat dissipation capability). The maximum junction temperature is typically equal to the maximum value in the storage temperature range. Heat generated by consumed power of IC radiates from the mold resin or lead frame of the package. The parameter which indicatesthis heat dissipation capability(hardness of heat release)is called thermal resistance, represented by the symbol θja[℃/W].The temperature of IC inside the package can be estimated by this thermal resistance. Fig.54(a) shows the model of thermal resistance of the package. Thermal resistance θja, ambient temperature Ta, junction temperature Tj, and power dissipation Pd can be calculated by the equation below: θja = (Tj-Ta) / Pd [℃/W] ・・・・・ (Ⅰ) Derating curve in Fig.54(b) indicates power that can be consumed by IC with reference to ambient temperature.Power that can be consumed by IC begins to attenuate at certain ambient temperature. This gradient iis determined by thermal resistance θja. Thermal resistance θja depends on chip size, power consumption, package,ambient temperature, package condition, wind velocity, etc even when the same of package is used. Thermal reduction curve indicates a reference value measured at a specified condition. Fig.55(c),(d) show a derating curve for an example of BA2904Y, BA2902Y. LSI の 消 of LSI Power dissipation費 電 力 [ W] θja = ( Tj ー Ta ) / Pd [℃/W] Ambient temperature 周囲温度 Ta [℃] Pd (max) P2 θja2 < θja1 P1 θ' ja2 θ ja2 Tj ' (max) Tj (max) θ' ja1 θ ja1 75 100 125 150 Chip surface temperature Tj [℃] チップ 表面温度 Power dissipation [W] 消費電力 P Pd[W] 0 Ambient temperature Ta [ ℃ ] 周囲温度 25 50 (a) Thermal resistance Fig. 54 Thermal resistance and derating (b) Derating curve 1000 1000 870mW(*8) POWER DISSIPATION [mW] POWER DISSIPATION [mW] 800 780mW(*6) BA2904YF-C 590mW(*7) 800 610mW(*9) BA2902YFV-C 600 BA2904YFVM-C 600 BA2902YF-C 400 400 200 200 0 0 25 50 75 100 125 150 0 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [ ℃] AMBIENT TEMPERATURE [ ℃] (c) BA2904Y family (d) BA2902Y family (*6) 6.2 (*7) 4.8 (*8) 7.0 (*9) 4.9 Unit [mW/℃] When using the unit above Ta=25[℃], subtract the value above per degree [℃]. Permissible dissipation is the value when FR4 glass epoxy board 70[mm]×70[mm]×1.6[mm](cooper foil area below 3[%]) is mounted. Fig. 55 Derating curve www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 11/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C Technical Note ●Description of Electrical Characteristics Described below are descriptions of the relevant electrical terms Please note that item names, symbols and their meanings may differ from those on another manufacturer’s documents. 1.Absolute maximum ratings The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of electrical characteristics or damage to the part itself as well as peripheral components. 1.1 Power supply voltage (VCC-VEE) Expresses the maximum voltage that can be supplied between the positive and negative supply terminals without causing deterioration of the electrical characteristics or destruction of the internal circuitry. 1.2 Differential input voltage (Vid) Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC. 1.3 Input common-mode voltage range (Vicm) Signifies the maximum voltage that can be supplied to non-inverting and inverting terminals without causing deterioration of the characteristics or damage to the IC itself. Normal operation is not guaranteed within the common-mode voltage range of the maximum ratings – use within the input common-mode voltage range of the electric characteristics instead. 1.4 Operating and storage temperature ranges (Topr,Tstg) The operating temperature range indicates the temperature range within which the IC can operate. The higher the ambient temperature, the lower the power consumption of the IC. The storage temperature range denotes the range of temperatures the IC can be stored under without causing excessive deterioration of the electrical characteristics. 1.5 Power dissipation (Pd) Indicates the power that can be consumed by a particular mounted board at ambient temperature (25℃). For packaged products, Pd is determined by the maximum junction temperature and the thermal resistance. 2.Electrical characteristics 2.1 Input offset voltage (Vio) Signifies the voltage difference between the non-inverting and inverting terminals. It can be thought of as the input voltage difference required for setting the output voltage to 0 V. 2.2 Input offset voltage drift (△Vio/△T) Denotes the ratio of the input offset voltage fluctuation to the ambient temperature fluctuation. 2.3 Input offset current (Iio) Indicates the difference of input bias current between the non-inverting and inverting terminals. 2.4 Input offset current drift (△Iio/△T) Signifies the ratio of the input offset current fluctuation to the ambient temperature fluctuation. 2.5 Input bias current (Ib) Denotes the current that flows into or out of the input terminal, it is defined by the average of the input bias current at the non-inverting terminal and the input bias current at the inverting terminal. 2.6 Circuit current (ICC) Indicates the current of the IC itself that flows under specified conditions and during no-load steady state. 2.7 High level output voltage/low level output voltage (VOH/VOL) Signifying the voltage range that can be output under specified load conditions, it is in general divided into high level output voltage and low level output voltage. High level output voltage indicates the upper limit of the output voltage, while low level output voltage the lower limit. 2.8 Large signal voltage gain (AV) The amplifying rate (gain) of the output voltage against the voltage difference between non-inverting and inverting terminals, it is (normally) the amplifying rate (gain) with respect to DC voltage. AV = (output voltage fluctuation) / (input offset fluctuation) 2.9 Input common-mode voltage range (Vicm) Indicates the input voltage range under which the IC operates normally. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 12/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C Technical Note 2.10 Common-mode rejection ratio (CMRR) Signifies the ratio of fluctuation of the input offset voltage when the in-phase input voltage is changed (DC fluctuation). CMRR = (change in input common-mode voltage) / (input offset fluctuation) 2.11 Power supply rejection ratio (PSRR) Denotes the ratio of fluctuation of the input offset voltage when supply voltage is changed (DC fluctuation). SVR = (change in power supply voltage) / (input offset fluctuation) 2.12 Output source current/ output sink current (IOH/IOL) The maximum current that can be output under specific output conditions, it is divided into output source current and output sink current. The output source current indicates the current flowing out of the IC, and the output sink current the current flowing into the IC. 2.13 Channel separation (CS) Expresses the amount of fluctuation of the input offset voltage or output voltage with respect to the change in the output voltage of a driven channel. 2.14 Slew rate (SR) Indicates the time fluctuation ratio of the output voltage when an input step signal is supplied. 2.15 Gain bandwidth product (GBW) The product of the specified signal frequency and the gain of the op-amp at such frequency, it gives the approximate value of the frequency where the gain of the op-amp is 1 (maximum frequency, and unity gain frequency) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 13/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C ●Notes for use 1) Unused circuits When there are unused circuits, it is recommended that they be connected as in Fig.56, setting the non-inverting input terminal to a potential within the in-phase input voltage range (Vicm). 2) Input voltage Applying VEE+36[V] to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. Technical Note VCC Please keep this 同相入力電圧 potencial in Vicm 範囲内の電位 VEE Fig. 56 Example of processing unused circuit 3) Power supply (single / dual) The op-amp operates when the voltage supplied is between VCC and VEE Therefore, the single supply op-mp can be used as a dual supply op-amp as well. 4) Power dissipation (Pd) Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to the rise in chip temperature, including reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal derating curves for more information. 5) Short-circuit between pins and erroneous mounting Incorrect mounting may damage the IC. In addition, the presence of foreign substances between the outputs, the output and the power supply, or the output and GND may result in IC destruction. 6) Operation in a strong electromagnetic field Operation in a strong electromagnetic field may cause malfunctions. 7) Radiation This IC is not designed to withstand radiation. 8) IC handing Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuation of the electrical characteristics due to piezoelectric (piezo) effects. 9) IC operation The output stage of the IC is configured using Class C push-pull circuits. Therefore, when the load resistor is connected to the middle potential of VCC and VEE, crossover distortion occurs at the changeover between discharging and charging of the output current. Connecting a resistor between the output terminal and GND, and increasing the bias current for Class A operation will suppress crossover distortion. 10) Board inspection Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition, when attaching and detaching the jig during the inspection phase, ensure that the power is turned OFF before inspection and removal. Furthermore, please take measures against ESD in the assembly process as well as during transportation and storage. 11) Output capacitor Discharge of the external output capacitor to VCC is possible via internal parasitic elements when VCC is shorted to VEE, causing damage to the internal circuitry due to thermal stress. Therefore, when using this IC in circuits where oscillation due to output capacitive load does not occur, such as in voltage comparators, use an output capacitor with a capacitance less than 0.1μF. 12) Oscillation by output capacitor Please pay attention to oscillation by output capacitor, designing application of negative feed back loop circuit with these ICs. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 14/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C ●Ordering part number Technical Note B Part No. A 2 Part No. 2904Y 2902Y 9 0 2 Y F V - C E 2 Package F : SOP8 SOP14 FV : SSOP-B14 FVM : MSOP8 Automotive Packaging and forming specification series E2: Embossed tape and reel (SOP8/SOP14/ SSOP-B14) TR: Embossed tape and reel (MSOP8) SOP8 5.0±0.2 (MAX 5.35 include BURR) 8 7 6 5 +6° 4° −4° 0.9±0.15 0.3MIN Tape Quantity Direction of feed Embossed carrier tape 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold 6.2±0.3 4.4±0.2 ( reel on the left hand and you pull out the tape on the right hand ) 12 3 4 0.595 1.5±0.1 +0.1 0.17 -0.05 S 0.1 0.11 S 1.27 0.42±0.1 1pin Direction of feed (Unit : mm) Reel ∗ Order quantity needs to be multiple of the minimum quantity. SOP14 8.7 ± 0.2 (MAX 9.05 include BURR) 14 8 Tape Quantity Direction of feed 0.3MIN Embossed carrier tape 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold 6.2 ± 0.3 4.4 ± 0.2 ( reel on the left hand and you pull out the tape on the right hand ) 1 7 0.15 ± 0.1 1.5 ± 0.1 0.11 1.27 0.4 ± 0.1 0.1 1pin (Unit : mm) Direction of feed Reel ∗ Order quantity needs to be multiple of the minimum quantity. SSOP-B14 5.0 ± 0.2 14 8 Tape Quantity 0.3Min. Embossed carrier tape 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold 6.4 ± 0.3 4.4 ± 0.2 Direction of feed ( reel on the left hand and you pull out the tape on the right hand ) 1 7 0.15 ± 0.1 1.15 ± 0.1 0.10 0.65 0.1 0.22 ± 0.1 1pin (Unit : mm) Direction of feed Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 15/16 2011.08 - Rev.B BA2904YF-C,BA2904YFVM-C,BA2902YF-C,BA2902YFV-C Technical Note MSOP8 2.9±0.1 (MAX 3.25 include BURR) 8765 Tape 0.29±0.15 0.6±0.2 Embossed carrier tape 3000pcs TR The direction is the 1pin of product is at the upper right when you hold +6° 4° −4° Quantity Direction of feed 4.0±0.2 2.8±0.1 ( reel on the left hand and you pull out the tape on the right hand 1pin ) 1 234 1PIN MARK 0.475 0.9MAX +0.05 0.145 −0.03 S 0.75±0.05 0.08±0.05 +0.05 0.22 −0.04 0.08 S 0.65 Direction of feed (Unit : mm) Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 16/16 2011.08 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A