BD2061AFJ

Power Management Switch ICs for PCs and Digital Consumer Products 1ch High Side Switch ICs for USB Devices and Memory Cards BD2061AFJ,BD2065AFJ No.11029ECT06 ●Description Single channel high side switch IC for USB port is a high side switch having over current protection used in power supply line of universal serial bus (USB). N-channel power MOSFET of low on resistance and low supply current are realized in this IC. And, over current detection circuit, thermal shutdown circuit, under voltage lockout and soft start circuit are built in. ●Features 1) Low on resistance 80mΩ Nch MOSFET Switch. 2) Continuous current load 1.0A 3) Control input logic Active-Low : BD2061AFJ Active-High : BD2065AFJ 4) Soft start circuit 5) Over current detection 6) Thermal shutdown 7) Under voltage lockout 8) Open drain error flag output 9) Reverse-current protection when power switch off 10) Power supply voltage range 2.7V~5.5V 11) TTL Enable input 12) 1.2ms typical rise time 13) 10μA max standby current 14) Operating temperature range -40℃~85℃ ●Applications USB hub in consumer appliances, Car accessory, PC, PC peripheral equipment, and so forth ●Lineup Parameter Continuous current load (A) Output current at short (A) Control input logic ●Absolute Maximum Ratings Parameter Supply voltage Enable voltage /OC voltage /OC current OUT voltage Storage temperature Power dissipation BD2061AFJ 1.0 1.5 Low BD2065AFJ 1.0 1.5 High Symbol VIN VEN, V/EN V/OC IS/OC VOUT TSTG PD Ratings -0.3 -0.3 -0.3 -0.3 to to to 10 to 560*1 6.0 -55 to 150 6.0 6.0 6.0 Unit V V V mA V ℃ mW *1 In the case of exceeding Ta = 25℃, 4.48mW should be reduced per 1℃. * This chip is not designed to protect itself against radioactive rays. ●Operating conditions Parameter Operating voltage Operating temperature Continuous output current Symbol VIN TOPR ILO Ratings 2.7 to 5.5 -40 to 85 0 to 1.0 Unit V ℃ A www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ ●Electrical characteristics ◎BD2061AFJ (Unless otherwise specified, VIN = 5.0V, Ta = 25℃) Parameter Operating Current Standby Current /EN input voltage /EN input current /OC output LOW voltage /OC output leak current /OC delay time ON resistance Output current at short Output rise time Output turn on time Output fall time Output turn off time UVLO threshold Symbol IDD ISTB V/EN V/EN I/EN V/OC IL/OC TD/OC RON ISC TON1 TON2 TOFF1 TOFF2 VTUVH VTUVL Limits Min. 2.0 -1.0 1.1 2.1 2.0 Typ. 90 0.01 0.01 0.01 2.5 80 1.5 1.2 1.5 1 3 2.3 2.2 Max. 120 1 0.8 0.4 1.0 0.5 1 8 100 1.9 10 20 20 40 2.5 2.4 Unit μA μA V V V μA V μA ms mΩ A ms ms μs μs V V Increasing VIN Decreasing VIN IOUT = 1.0A Technical Note Condition V/EN = 0V, OUT = OPEN V/EN = 5V, OUT = OPEN High input Low input Low input 2.7V≤ VIN ≤4.5V V/EN = 0V or V/EN = 5V I/OC = 5mA V/OC = 5V VIN = 5V, VOUT = 0V, CL = 100μF (RMS) RL = 10Ω , CL = OPEN ◎BD2065AFJ (Unless otherwise specified, VIN = 5.0V, Ta = 25℃) Limits Parameter Symbol Min. Typ. Max. IDD ISTB VEN 2.0 -1.0 1.1 2.1 2.0 90 0.01 0.01 0.01 2.5 80 1.5 1.2 1.5 1 3 2.3 2.2 120 1 0.8 0.4 1.0 0.5 1 8 100 1.9 10 20 20 40 2.5 2.4 Unit μA μA V V V μA V μA ms mΩ A ms ms μs μs V V Condition VEN = 5V, OUT = OPEN VEN = 0V, OUT = OPEN High input Low input Low input 2.7V≤ VIN ≤4.5V VEN = 0V or VEN = 5V I/OC = 5mA V/OC = 5V IOUT = 1.0A VIN = 5V, VOUT = 0V, CL = 100μF (RMS) Operating Current Standby Current EN input voltage EN input current /OC output LOW voltage /OC output leak current /OC delay time ON resistance Output current at short Output rise time Output turn on time Output fall time Output turn off time UVLO Threshold VEN IEN V/OC IL/OC TD/OC RON ISC TON1 TON2 TOFF1 TOFF2 VTUVH VTUVL RL = 10Ω , CL = OPEN Increasing VIN Decreasing VIN www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ ●Measurement circuit VIN A 1uF GND IN IN EN(/EN) VEN (V/EN ) OUT OUT OUT /OC Technical Note VIN 1uF GND IN IN EN(/EN) VEN (V/EN ) OUT OUT OUT /OC RL CL Operating current EN, /EN input voltage, Output rise, fall time VIN VIN 10k GND IN IN EN(/EN) OUT OUT OUT /OC IOUT CL VIN VIN 1uF 1uF GND IN IN EN(/EN) VEN (V/EN ) OUT OUT OUT /OC I/OC VEN (V/EN ) ON resistance, Over current detection Fig.1 Measurement circuit /OC output LOW voltage ●Timing diagram ○BD2061AFJ TOFF1 TON1 VOUT 10% 90% 90% 10% TOFF2 TON2 V/EN 50% Fig.2 Timing diagram 50% VEN 50% Fig.3 Timing diagram 50% TON2 VOUT 10% TON1 90% 90% 10% TOFF2 ○BD2065AFJ TOFF1 www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ ●Reference data 120 Ta=25°C OPERATING CURRENT : IDD [μA] OPERATING CURRENT : IDD [μA] 120 1.0 Technical Note VIN=5.0V 100 80 60 40 20 0 STANDBY CURRENT : ISTB[μA] 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 0.8 Ta=25°C 100 80 60 40 20 0 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 0.6 0.4 0.2 0.0 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 Fig.4 Operating current EN,/EN Enable Fig.5 Operating current EN,/EN Enable Fig.6 Standby current EN,/EN Disable 1.0 VIN=5.0V ENABLE INPUT VOLTAGE : VEN, V /EN[V] 0 2.0 2.0 ENABLE INPUT VOLTAGE : VEN, V/EN[V] Ta=25°C 1.5 VIN=5.0V 1.5 0.8 STANDBY CURRENT : ISTB[μA] Low to High High to Low 0.6 0.4 Low to High 1.0 High to Low 1.0 0.2 0.5 0.5 0.0 -50 0 50 100 AMBIENT TEMPERATURE : Ta[℃] 0.0 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 0.0 -50 0 50 AMBIENT TEMPERATURE : Ta[℃] 100 Fig.7 Standby current EN,/EN Disable Fig.8 EN,/EN input voltage Fig.9 EN,/EN input voltage 0.5 /OC OUTPUT LOW VOLTAGE : V/OC[V] /OC OUTPUT LOW VOLTAGE : V/OC[V] 0.5 200 VIN=5.0V Ta=25°C 0.4 Ta=25°C 150 0.4 0.3 0.3 0.2 ON RESISTANCE : R ON[mΩ] -50 0 50 100 AMBIENT TEMPERATURE : Ta[℃] 100 0.2 0.1 0.1 0.0 50 0.0 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 0 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 Fig.10 /OC output LOW voltage Fig.11 /OC output LOW voltage Fig.12 ON resistance 200 VIN=5.0V ON RESISTANCE : RON[mΩ] 5.0 Ta=25°C 4.0 /OC DELAY TIME : TD/OC[mS] 5.0 VIN=5.0V 4.0 150 /OC DELAY TIME : TD/OC[mS] 3.0 2.0 3.0 2.0 100 50 1.0 0.0 1.0 0.0 0 -50 0 50 100 AMBIENT TEMPERATURE : Ta[℃] 2 3 4 5 SUPPLY VOLTAGE : VIN[V] 6 -50 50 100 0 AMBIENT TENPERATURE : Ta[℃] Fig.13 ON resistance Fig.14 /OC output delay time Fig.15 /OC output delay time www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ Technical Note 2.00 2.00 SHORT CIRCUIT CURRENT : ISC [A] 5.0 SHORT CIRCUIT CURRENT : ISC [A] Ta=25°C 1.50 VIN=5.0V 1.50 Ta=25°C 4.0 1.00 1.00 0.50 0.50 0.00 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 0.00 -50 0 50 100 AM BIEN T TEM PER ATU R E : Ta[℃ ] RISE TIME : T ON1 [ms] 3.0 2.0 1.0 0.0 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 Fig.16 Output current at shortcircuit Fig.17 Output current at shortcircuit Fig.18 Output rise time 5.0 VIN=5.0V 4.0 TURN ON TIME : TON2 [ms] 5.0 5.0 Ta=25°C VIN=5.0V 4.0 TURN ON TIME : TON2 [ms] 3.0 4.0 RISE TIME : T ON1 [ms] 3.0 2.0 3.0 2.0 2.0 1.0 0.0 -50 1.0 1.0 0.0 -50 0.0 0 50 100 AMBIENT TEMPERATURE : Ta[℃] 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 0 50 100 AMBIENT TEMPERATURE : Ta[℃] Fig.19 Output rise time Fig.20 Output turn on time Fig.21 Output turn on time 5.0 5.0 5.0 VIN=5.0V Ta=25°C 4.0 TURN OFF TIME : TOFF2 [μs] Ta=25°C 4.0 4.0 3.0 FALL TIME : T OFF1 [μs] FALL TIME : T OFF1 [μs] 3.0 2.0 3.0 2.0 2.0 1.0 1.0 1.0 0.0 -50 0 50 100 AMBIENT TEMPERATURE : Ta[℃] 0.0 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 0.0 2 3 4 5 SUPPLY VOLTAGE : VIN [V] 6 Fig.22 Output fall time Fig.23 Output fall time Fig.24 Output turn off time 5.0 UVLO THRESHOLD VOLTAGE : VUVLOH , VUVLOL [V] 2.5 1.0 0.8 0.6 0.4 0.2 0.0 -50 0 50 100 AMBIENT TEMPERATURE : Ta[℃] VIN=5.0V 4.0 TURN OFF TIME : TOFF2 [μs] VUVLOH 2.3 3.0 2.0 2.2 2.1 VUVLOL 1.0 0.0 -50 0 50 100 AMBIENT TEMPERATURE : Ta[℃] 2.0 -50 0 50 100 AMBIENT TEMPERATURE : Ta[℃] Fig.25 Output turn off time Fig.26 UVLO threshold voltage UVLO HYSTERESIS VOLTAGE : VHYS[V] 2.4 Fig.27 UVLO hysteresis voltage www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 5/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ ●Waveform data V/EN (5V/div.) V/OC (5V/div.) V/EN (5V/div.) Technical Note VEN (5V/div.) V/OC (5V/div.) CL=220μF IOUT (0.5A/div.) CL=147μF CL=47μF VIN=5V RL= 5Ω CL=330μF V/OC (5V/div.) VOUT (5V/div.) VOUT (5V/div.) IOUT (0.5A/div.) VIN=5V RL=10Ω CL=100μF TIME(1ms/div.) IOUT (0.5A/div.) VIN=5V RL=10Ω CL=100μF TIME(1ms/div.) TIME (0.5ms/div.) Fig.28 Output rise characteristic (BD2061AFJ) V/OC (5V/div.) VOUT (5V/div.) Fig.29 Output fall characteristic (BD2061AFJ) V/OC (5V/div.) VOUT (5V/div.) Fig30 Inrush current response (BD2061AFJ) IOUT (1.0A/div.) VIN=5V TIME (20ms/div.) IOUT (1.0A/div.) TIME (2ms/div.) VIN=5V Fig.31 Over current response Ramped load (BD2061AFJ) V/EN (5V/div.) V/OC (5V/div.) VOUT (5V/div.) V/OC (5V/div.) Fig.32 Over current response Ramped load (BD2061AFJ) V/OC (5V/div.) VOUT (5V/div.) VOUT (5V/div.) Thermal Shutdown VIN=5V CL=100μF IOUT (1.0A/div.) VIN=5V CL=100μF TIME (2ms/div.) IOUT (1.0A/div.) TIME (2ms/div.) VIN=5V CL=100μF IOUT (1.0A/div.) TIME (0.2s/div.) Fig.33 Over current response Enable to shortcircuit (BD2061AFJ) VIN (5V/div.) VIN (5V/div.) VOUT (5V/div.) IOUT (1.0A/div.) V/OC (5V/div.) V/OC (5V/div.) TIME (10ms/div.) RL=5Ω CL=147μF Fig.34 Over current response Enable to shortcircuit (BD2061AFJ) Fig.35 Over current response Enable to shortcircuit (BD2061AFJ) VOUT (5V/div.) IOUT (1.0A/div.) RL=5Ω CL=147μF TIME (10ms/div.) Fig.36 UVLO response Increasing VIN (BD2061AFJ) Fig.37 UVLO response Decreasing VIN (BD2061AFJ) Regarding the output rise/fall and over current detection characteristics of BD2065AFJ, refer to the characteristic of BD2061AFJ. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ ●Block diagram GND OUT Technical Note IN UVLO Charge pump OCD OUT GND IN IN 1 2 3 4 8 7 6 5 OUT OUT OUT /OC IN Gate logic OUT Top View EN(/EN) TSD /OC EN(/EN) Fig.38 Block diagram Fig.39 Pin Configuration ●Pin description ◎BD2061AFJ Pin No. Symbol 1 GND I/O I Ground. Pin function 2, 3 IN I Power supply input. Input terminal to the power switch and power supply input terminal of the internal circuit. At use, connect each pin outside. Enable input. Power switch on at Low level. High level input > 2.0V, Low level input < 0.8V. Error flag output. Low at over current, thermal shutdown. Open drain output. Power switch output. At use, connect each pin outside. 4 /EN I 5 /OC O 6, 7, 8 OUT O ◎BD2065AFJ Pin No. Symbol 1 GND I/O I Ground. Pin function 2, 3 IN I Power supply input. Input terminal to the power switch and power supply input terminal of the internal circuit. At use, connect each pin outside. Enable input. Power switch on at High level. High level input > 2.0V, Low level input < 0.8V Error flag output. Low at over current, thermal shutdown. Open drain output. Power switch output. At use, connect each pin outside. 4 EN I 5 /OC O 6, 7, 8 OUT O www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 7/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ ●I/O circuit Symbol Technical Note Pin No Equivalent circuit EN(/EN) 4 /OC 5 OUT 6,7,8 ●Functional description 1. Switch operation IN terminal and OUT terminal are connected to the drain and the source of switch MOSFET respectively. And the IN terminal is used also as power source input to internal control circuit. When the switch is turned on from EN/EN control input, IN terminal and OUT terminal are connected by a 80mΩ switch. In on status, the switch is bidirectional. Therefore, when the potential of OUT terminal is higher than that of IN terminal, current flows from OUT terminal to IN terminal. Since a parasitic diode between the drain and the source of switch MOSFET is canceled, in the off status, it is possible to prevent current from flowing reversely from OUT to IN. 2. Thermal shutdown circuit (TSD) If over current would continue, the temperature of the IC would increase drastically. If the junction temperature were beyond 140℃ (typ.) in the condition of over current detection, thermal shutdown circuit operates and makes power switch turn off and outputs error flag (/OC). Then, when the junction temperature decreases lower than 120℃ (typ.), power switch is turned on and error flag (/OC) is cancelled. Unless the fact of the increasing chips temperature is removed or the output of power switch is turned off, this operation repeats. The thermal shutdown circuit operates when the switch is on (EN,/EN signal is active). 3. Over current detection (OCD) The over current detection circuit limits current (ISC) and outputs error flag (/OC) when current flowing in each switch MOSFET exceeds a specified value. There are three types of response against over current. The over current detection circuit works when the switch is on (EN,/EN signal is active). 3-1. When the switch is turned on while the output is in shortcircuit status When the switch is turned on while the output is in shortcircuit status or so, the switch gets in current limit status soon. 3-2. When the output shortcircuits while the switch is on When the output shortcircuits or large capacity is connected while the switch is on, very large current flows until the over current limit circuit reacts. When the current detection, limit circuit works, current limitation is carried out. 3-3. When the output current increases gradually When the output current increases gradually, current limitation does not work until the output current exceeds the over current detection value. When it exceeds the detection value, current limitation is carried out. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ Technical Note 4. Under voltage lockout (UVLO) UVLO circuit prevents the switch from turning on until the VIN exceeds 2.3V(Typ.). If the VIN drops below 2.2V(Typ.) while the switch turns on, then UVLO shuts off the power switch. UVLO has hysteresis of a 100mV(Typ). Under voltage lockout circuit works when the switch is on (EN,/EN signal is active). 5. Error flag (/OC) output Error flag output is N-MOS open drain output. At detection of over current, thermal shutdown, low level is output. Over current detection has delay filter. This delay filter prevents instantaneous current detection such as inrush current at switch on, hot plug from being informed to outside. V/EN VOUT Output shortcircuit Thermal shut down IOUT V/OC delay Fig.40 Over current detection, thermal shutdown timing (BD2061AFJ) VEN VOUT Output shortcircuit Thermal shut down IOUT V/OC delay Fig.41 Over current detection, thermal shutdown timing (BD2065AFJ) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 9/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ ●Typical application circuit 5V(typ.) VBUS D+ DGND 10k~ 100kΩ CIN GND IN IN OUT OUT OUT + CL IN Regulator OUT Technical Note Ferrite Beads VBUS D+ DFerrite Beads GND USB Controller EN(/EN) /OC Fig.42 Typical application circuit ●Application information When excessive current flows owing to output shortcircuit or so, ringing occurs by inductance of power source line to IC, and may cause bad influences upon IC actions. In order to avoid this case, connect a bypath capacitor by IN terminal and GND terminal of IC. 1μF or higher is recommended. Pull up /OC output by resistance 10kΩ ~ 100kΩ. Set up value which satisfies the application as CL and Ferrite Beads. This system connection diagram doesn’t guarantee operating as the application. The external circuit constant and so on is changed and it uses, in which there are adequate margins by taking into account external parts or dispersion of IC including not only static characteristics but also transient characteristics. ●Power dissipation character (SOP-J8) 600 500 POWER DISSIPATION: Pd[mW] 400 300 200 100 0 0 25 50 75 100 125 150 AMBIENT TEMPERATURE: Ta [℃] Fig.43 Power dissipation curve (Pd-Ta Curve) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 10/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ Technical Note ●Notes for use (1) Absolute Maximum Ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety measures including the use of fuses, etc. (2) Operating conditions These conditions represent a range within which characteristics can be provided approximately as expected. The electrical characteristics are guaranteed under the conditions of each parameter. (3) Reverse connection of power supply connector The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown due to the reverse connection, such as mounting an external diode between the power supply and the IC’s power supply terminal. (4) Power supply line Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. In this regard, for the digital block power supply and the analog block power supply, even though these power supplies has the same level of potential, separate the power supply pattern for the digital block from that for the analog block, thus suppressing the diffraction of digital noises to the analog block power supply resulting from impedance common to the wiring patterns. For the GND line, give consideration to design the patterns in a similar manner. Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to be used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant. (5) GND voltage Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state. Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric transient. (6) Short circuit between terminals and erroneous mounting In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between the terminal and the power supply or the GND terminal, the ICs can break down. (7) Operation in strong electromagnetic field Be noted that using ICs in the strong electromagnetic field can malfunction them. (8) Inspection with set PCB On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress. Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the jig. After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In addition, for protection against static electricity, establish a ground for the assembly process and pay thorough attention to the transportation and the storage of the set PCB. (9) Input terminals In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of electrical characteristics. (10) Ground wiring pattern If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well. (11) External capacitor In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a degradation in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc. (12) Thermal shutdown circuit (TSD) When junction temperatures become detected temperatures or higher, the thermal shutdown circuit operates and turns a switch OFF. The thermal shutdown circuit, which is aimed at isolating the LSI from thermal runaway as much as possible, is not aimed at the protection or guarantee of the LSI. Therefore, do not continuously use the LSI with this circuit operating or use the LSI assuming its operation. (13) Thermal design Perform thermal design in which there are adequate margins by taking into account the power dissipation (Pd) in actual states of use. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 11/12 2011.05 - Rev.B BD2061AFJ,BD2065AFJ ●Ordering part number Technical Note B D 2 Part No. 2061A 2065A 0 6 1 A F J - E 2 Part No. Package FJ: SOP-J8 Packaging and forming specification E2: Embossed tape and reel (SOP-J8) SOP-J8 4.9±0.2 (MAX 5.25 include BURR) +6° 4° −4° 8 7 6 5 Tape Quantity 0.45MIN Embossed carrier tape 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold 6.0±0.3 3.9±0.2 Direction of feed ( reel on the left hand and you pull out the tape on the right hand ) 1 2 3 4 0.545 S 0.2±0.1 1.375±0.1 0.175 1.27 0.42±0.1 0.1 S 1pin (Unit : mm) Reel Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 12/12 2011.05 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A