BD3571FP

Power Management IC Series for Automotive Body Control High Voltage LDO Regulators BD3570FP, BD3570HFP, BD3571FP, BD3571HFP, BD3572FP, BD3572HFP BD3573FP, BD3573HFP, BD3574FP, BD3574HFP, BD3575FP, BD3575HFP No.11036EBT02 ●Description BD357XFP/HFP SERIES regulators feature a high 50 V withstand-voltage and are suitable for use with onboard vehicle microcontrollers. They offer the output current of 500 mA while limiting the quiescent current to 30μA (TYP).With these devices, a ceramic capacitor can be selected at the output for stable operation, the output tolerance is within ±2% over the wide ambient temperature range (-40 to 125℃), and the short circuit protection is folded-type to minimize generation of heat during malfunction. These devices are developed to offer most robust power-supply design under the harsh automotive environment. The BD357XFP/HFP Series provide ideal solutions to lower the current consumption as well as to simplify the use with battery direct-coupled systems. ●Features 1) Ultra-low quiescent current: 30μA (TYP.) 2) Low-saturation voltage type P-channel DMOS output transistors 3) High output voltage precision:  2%／Iomax = 500 mA 4) Low-ESR ceramic capacitors can be used as output capacitors. 5) Vcc power supply voltage = 50 V 6) Built-in overcurrent protection circuit and thermal shutdown circuit 7) TO252-3, TO252-5, HRP5 Package ●Applications Onboard vehicle devices (body-control, car stereos, satellite navigation systems, etc.) ●Line up matrix BD3570FP/HFP BD3571FP/HFP BD3572FP/HFP BD3573FP/HFP BD3574FP/HFP BD3575FP/HFP Output voltage SW function Package HFP:HRP5 3.3V － FP:TO252-3,TO252-5 5.0 V － Variable － 3.3V 〇 5.0 V 〇 Variable 〇 ●Absolute maximum ratings (Ta=25℃) Parameter Supply voltage Switch Supply voltage Output current Power dissipation Operating temperature range Storage temperature range Maximum junction temperature ※1 ※2 ※3 ※4 ※5 Symbol VCC VSW IO Pd Topr Tstg Tjmax Limit 50 50 500 1.2 (TO252-3) ※3 1.3 (TO252-5) ※4 1.6 (HRP5) -40 to +125 -55 to +150 150 ※5 ※1 ※2 Unit V V mA W ℃ ℃ ℃ Not to exceed Pd and ASO. for ON/OFF SW Regulator only TO252-3: Reduced by 9.6 mW/℃ over 25 ℃, when mounted on a glass epoxy board (70 mm  70 mm  1.6 mm). TO252-5: Reduced by 10.4 mW/℃ over 25 ℃, when mounted on a glass epoxy board (70 mm  70 mm  1.6 mm). HRP5: Reduced by 12.8 mW/℃ over 25 ℃, when mounted on a glass epoxy board (70 mm  70 mm  1.6 mm). www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1/9 2011.03 - Rev.B BD3570FP/HFP, BD3571FP/HFP, BD3572FP/HFP, BD3573FP/HFP BD3574FP/HFP, BD3575FP/HFP ●Operating Conditions Parameter Input voltage BD3570,3572,3573,3575FP/HFP BD3571,3574FP/HFP Output current Variable Output Voltage Range Symbol VCC VCC IO VO Min. 4.5 ※6 5.5 ※6 － 2.8 Max. 36.0 36.0 500 12 Technical Note Unit V V mA V ※6 Please consider that the Output voltage would be dropped (Dropout voltage) according to the output current. ●Electrical Characteristics（Unless otherwise specified, Ta=-40 to125℃, VCC=13.2 V, SW=3V ※7, VO settings is 5V ※8） Parameter Shut Down Current Bias current Output voltage ADJ Terminal voltage Output current Dropout voltage Ripple rejection Line Regulation Load Regulation Swith Threshold voltage H Swith Threshold voltage L Swith Bias current ※7 ※8 ※9 ※10 Symbol ※７ lshut lb VO ※8 VADJ IO △Vd R.R. Reg.I Reg.L ※７ ※７ ※７ SWH SWL SWI Limit Min. － － VO× 0.98 1.235 0.5 － 45 － － 2.0 － － Typ. － 30 VO 1.260 － 0.25 55 10 20 － － 22 Max. 10 50 VO× 1.02 1.285 － 0.48 － 30 40 － 0.5 60 Unit μA μA V V A V dB mV mV V V μA SW=GND IO=0mA Conditions IO=200mA, VO:Please refer to Product line. IO=200mA VCC=4.75V,lO=200mA ※9 f=120Hz,ein=1Vrms,IO=100mA VCCD※10≦VCC≦25V IO = 0 mA 0ｍA≦IO≦200ｍA IO=0 mA IO=0 mA SW=5V,lO=0mA BD3573,3574,3575FP/HFP only BD3572,3575FP/HFP only BD3571,3572,3574,3575FP/HFP only BD3570,3573FP/HFP :VCCD=5.5V BD3571,3572,3574,3575FP/HFP :VCCD=6.5V ○This product is not designed for protection against radio active rays. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/9 2011.03 - Rev.B BD3570FP/HFP, BD3571FP/HFP, BD3572FP/HFP, BD3573FP/HFP BD3574FP/HFP, BD3575FP/HFP ●Reference Data: BD3574HFP（Unless otherwise specified, Ta=25℃） 50 CIRCUIT CURRENT: I CC [μA] 6 5 4 3 Technical Note 6 5 4 Ta=-40℃ 3 2 1 0 0 5 10 15 20 25 OUTPUT VOLTAGE: VO [V] 30 20 Ta=125℃ Ta=25℃ Ta=125℃ 2 OUTPUT VOLTAGE: VO [V] 40 Ta=25℃ Ta=125℃ Ta=25℃ 1 0 10 Ta=-40℃ 0 0 5 10 15 20 25 SUPPLY VOLTAGE: VCC [V] Ta=-40℃ 0 500 1000 1500 2000 SUPPLY VOLTAGE: VCC [V] OUTPUT CURRENT: IO [mA] Fig. 1 Total Supply Current Fig. 2 Output Voltage VS Power Supply Voltage 70 Fig. 3 Output Voltage VS Load 3 6 RIPPLE REJECTION:R.R. [dB] DROPOUT VOLTAGE:ΔVd[V] 60 50 40 30 20 10 0 Ta=125℃ Ta=25℃ OUTPUT VOLTAGE: VO [V] 5 4 2 Ta=25℃ Ta=125℃ Ta=125℃ Ta=25℃ 1 Ta=-40℃ 3 2 1 0 Ta=-40℃ Ta=-40℃ 0 0 100 200 300 400 500 OUTPUT CURRENT: IO[mA] 10 100 1000 10000 100000 1000000 0 0.5 1 1.5 2 FREQUENCY: f [Hz] SUPPLY VOLTAGE: VSW [V] Fig. 4 Dropout Voltage 100 CIRCUIT CURRENT: I CC [μA] Fig. 5 Ripple rejection 6 5 4 3 2 1 0 100 5.5 Fig. 6 Output Voltage VS SW Input Voltage OUTPUT VOLTAGE: VO [V] OUTPUT VOLTAGE: VO [V] 80 5.25 60 5 40 20 4.75 0 0 100 200 300 400 500 OUTPUT CURRENT: IO[mA] 120 140 160 180 200 4.5 -40 0 40 80 120 AMBIENT TEMPERATURE: Ta [℃] AMBIENT TEMPERATURE: Ta [℃] Fig. 7 Total Supply Current Classified by Load 120 DROPOUT VOLTAGE:ΔVd [V] Fig. 8 Thermal Shutdown Circuit Fig. 9 Output Voltage VS Temperature 50 CIRCUIT CURRENT: I cc [μA] 2 SW BIAS CURRENT: ISW [μA] 40 90 Ta=125℃ 60 Ta=25℃ 30 Ta=-40℃ 0 0 5 10 15 20 25 SUPPLY VOLTAGE: VSW [V] 1.5 30 1 20 0.5 10 0 -40 0 40 80 120 0 -40 0 40 80 120 AMBIENT TEMPERATURE: Ta [℃] AMBIENT TEMPERATURE: Ta [℃] Fig. 10 SW Bias current Fig. 11 Dropout voltage VS Temperature Fig. 12 Total Supply Current Temperature www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/9 2011.03 - Rev.B BD3570FP/HFP, BD3571FP/HFP, BD3572FP/HFP, BD3573FP/HFP BD3574FP/HFP, BD3575FP/HFP ●Block Diagram Vcc 1 Cin Vref Vo 3 OCP Co OCP ＊1） ＊2） Cin SW 2 5 Co Vref Vo SW 2 OCP Vcc 1 Cin Vref Vcc 1 Technical Note Vo 5 Co ＊1） GND Fin TSD 2 GND Fin TSD 3 N.C. 4 GND Fin 3 ＊2） TSD 4 Fig.13 TO252-3 N.C. ADJ (N.C. ＊1) ) Fig.14 TO252-5 Cin 0.33μF～1000μF ： Co：0.1μF～1000μF Fig.15 HRP5 ADJ (N.C. ＊1) ) ＊1）For Fixed Voltage Regulator only ＊2）For adjustable Voltage Regulator only Vcc ●I/O Circuit diagram (All resistance values are typical.) SW Vo Vcc 210K 1K Vo 200K 1992K: BD3570, BD3573 3706K: BD3571, BD3574 150 1250K Fig.16 2PIN[SW] ●Pin Assignments FIN Fig.17 5PIN[VO] BD3570,3571,3573,3574 Fig.18 4.5PIN[ADJ,VO] BD3572,BD3575 TO252-3 Pin No. 1 2 3 1 23 Fig. 19 FIN Pin No. 1 Fin Pin name VCC N.C. VO GND N.C. pin Function Power supply pin Voltage output pin GND pin Pin name VCC SW N.C. N.C. N.C. ADJ VO GND Function Power supply pin VO ON/OFF function pin N.C. pin(BD3572FP only) N.C. pin N.C. pin Output voltage setting pin(BD3572,3575FP only) Voltage output pin GND pin TO252-5 2 3 1 2345 Fig.20 4 5 Fin FIN HRP5 Pin No. 1 2 3 Pin name VCC SW N.C. GND N.C. ADJ VO GND Function Power supply pin VO ON/OFF function pin (BD3573,3574,3575HFP only) N.C. pin GND pin N.C. pin Output voltage setting pin(BD3572,3575HFP only) Voltage output pin GND pin 1 23 45 Fig. 21 4 5 Fin www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/9 2011.03 - Rev.B BD3570FP/HFP, BD3571FP/HFP, BD3572FP/HFP, BD3573FP/HFP BD3574FP/HFP, BD3575FP/HFP ●Output Voltage Adjustment Vo Technical Note R2 To set the output voltage insert pull-down resistor R1 between the ADJ and GND pins, and pull-up resistor R2 between the VO and ADJ pins. Vo = VADJ×(R1+R2) / R1 [V] ｛VADJ=1.26V(TYP.)｝ The recommended connection resistor for the ADJ-GND is 30k～150kΩ. ADJ R1 Fig.22 ●Setting of Heat TO252-3 2.0 IC mounted on a ROHM standard board Substrate size: 70 mm  70 mm  1.6 mm ja = 104.2 (°C/W) TO252-5 2.0 IC mounted on a ROHM standard board Substrate size: 70 mm  70 mm  1.6 mm ja = 96.2 (°C/W) HRP5 2.0 1.6 W IC mounted on a ROHM standard board Substrate size: 70 mm  70 mm  1.6 mm ja = 78.1 (°C/W) POWER DISSIPATION: Pd [W] POWER DISSIPATION: Pd [W] 1.2 1.2 W 1.3W 1.2 POWER DISSIPATION: Pd [W] 1.6 1.6 1.6 1.2 0.8 0.8 0.8 0.4 0 0 25 50 75 100 125 150 0.4 0 0 25 50 75 100 125 150 0.4 0 0 25 50 75 100 125 150 AMBIENT TEMPERATURE: Ta [°C] AMBIENT TEMPERATURE: Ta [℃] AMBIENT TEMPERATURE: Ta [°C] Fig. 23 Fig. 24 Fig. 25 Refer to the heat mitigation characteristics illustrated in Figs. 23, 24 and 25 when using the IC in an environment where Ta ≧25℃. The characteristics of the IC are greatly influenced by the operating temperature. If the temperature is in excess of the maximum junction temperature Tjmax, the elements of the IC may be deteriorated or damaged. It is necessary to give sufficient consideration to the heat of the IC in view of two points, i.e., the protection of the IC from instantaneous damage and the maintenance of the reliability of the IC in long-time operation. In order to protect the IC from thermal destruction, it is necessary to operate the IC not in excess of the maximum junction temperature Tjmax. Fig. 23 illustrates the power dissipation/heat mitigation characteristics for the TO252 package. Operate the IC within the power dissipation Pd. The following method is used to calculate the power consumption PC (W). Vcc : Input voltage Vo : Output voltage Io : Load current Icc : Total supply current PC=(VCC-VO)×IO+VCC×ICC Power dissipation Pd≦PC The load current IO is obtained to operate the IC within the power dissipation. Pd-VCC×ICC Io≦ (For more information about ICC, see page 12.) VCC-VO The maximum load current Iomax for the applied voltage VCC can be calculated during the thermal design process. ●Calculation example Example: BD3571FP VCC = 12 V and VO = 5 V at Ta = 85℃ IO≦ 0.624-12×ICC 12-5 (ICC=30μA) θja=104.2℃/W→-9.6mAW/℃ 25℃=1.2W→85℃=0.624W IO≦89mA Make a thermal calculation in consideration of the above so that the whole operating temperature range will be within the power dissipation. The power consumption Pc of the IC in the event of shorting (i.e., if the VO and GND pins are shorted) will be obtained from the following equation. Pc=VCC×(ICC+Ishort) Ishort = Short current www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 5/9 2011.03 - Rev.B BD3570FP/HFP, BD3571FP/HFP, BD3572FP/HFP, BD3573FP/HFP BD3574FP/HFP, BD3575FP/HFP Technical Note ●Peripheral Settings for Pins and Precautions 1) VCC pins Insert capacitors with a capacitance of 0.33μF to 1000μF between the VCC and GND pins. The capacitance varies with the application. Be sure to design the capacitance with a sufficient margin. 2) Capacitors for stopping oscillation for output pins Capacitors for stopping oscillation must be placed between each output pin and the GND pin. Use a capacitor within a capacitance range between 0.1μF and 1000μF. Since oscillation does not occur even for ESR values from 0.001Ω to 100Ω, a ceramic capacitor can be used. Abrupt input voltage and load fluctuations can affect output voltages. Output capacitor capacitance values should be determined after sufficient testing of the actual application. ●Operation Notes 1) Absolute maximum ratings Use of the IC in excess of absolute maximum ratings such as the applied voltage or operating temperature range may result in IC damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such damage is suffered. A physical safety measure such as a fuse should be implemented when use of the IC in a special mode where the absolute maximum ratings may be exceeded is anticipated. 2) GND potential Ensure a minimum GND pin potential in all operating conditions. 3) Setting of heat Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions. 4) Pin short and mistake fitting Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting may result in damage to the IC. Shorts between output pins or between output pins and the power supply and GND pins caused by the presence of a foreign object may result in damage to the IC. 5) Actions in strong magnetic field Use caution when using the IC in the presence of a strong magnetic field as doing so may cause the IC to malfunction. 6) Testing on application boards When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress. Always discharge capacitors after each process or step. Be sure to turn power off when mounting or dismounting jigs at the inspection stage. Furthermore, for countermeasures against static electricity, ground the equipment at the assembling stage and pay utmost attention at the time of transportation or storing the product. 7) This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. PN junction is formed by the P layer and the N layer of each element, and a variety of parasitic elements will be constituted. For example, when a resistor and transistor are connected to pins as shown in Fig. 19,  the P/N junction functions as a parasitic diode when GND>Pin A for the resistor or GND>Pin B for the transistor (NPN).  Similarly, when GND＞Pin B for the transistor (NPN), the parasitic diode described above combines with the N layer of other adjacent elements to operate as a parasitic NPN transistor. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/9 2011.03 - Rev.B BD3570FP/HFP, BD3571FP/HFP, BD3572FP/HFP, BD3573FP/HFP BD3574FP/HFP, BD3575FP/HFP Technical Note The formation of parasitic elements as a result of the relationships of the potentials of different pins is an inevitable result of the IC's architecture. The operation of parasitic elements can cause interference with circuit operation as well as IC malfunction and damage. For these reasons, it is necessary to use caution so that the IC is not used in a way that will trigger the operation of parasitic elements, such as by the application of voltages lower than the GND (P substrate) voltage to input pins. Resistor (Pin A) (Pin B) C Transistor (NPN) B E B C E P+ N N P N Parasitic element GND Parasitic element or transistor N P P+ P+ N P substr t GND P P+ N GND Parasitic element or transistor (Pin A) Parasitic elements (Pin B) Fig. 26 Example of a Simple Monolithic IC Architecture 8) Ground wiring patterns When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns, placing a single ground point at the application's reference point so that the pattern wiring resistance and voltage variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern of any external parts, either. 9) SW Pin Do not apply the voltage to SW pin when the VCC is not applied. And when the VCC is applied, the voltage of SW pin must not exceed VCC. 10) Thermal shutdown circuit (TSD) This IC incorporates a built-in thermal shutdown circuit for the protection from thermal destruction. The IC should be used within the specified power dissipation range. However, in the event that the IC continues to be operated in excess of its power dissipation limits, the attendant rise in the chip's temperature Tj will trigger the thermal shutdown circuit to turn off all output power elements. The circuit automatically resets once the chip's temperature Tj drops. The thermal shutdown circuit operates if the IC is under conditions in express of the absolute maximum ratings. Never design sets on the premise of using the thermal shutdown circuit. (See Fig. 8) 11) Overcurrent protection circuit (OCP) The IC incorporates a built-in overcurrent protection circuit that operates according to the output current capacity. This circuit serves to protect the IC from damage when the load is shorted. The protection circuit is designed to limit current flow by not latching in the event of a large and instantaneous current flow originating from a large capacitor or other component. These protection circuits are effective in preventing damage due to sudden and unexpected accidents. However, the IC should not be used in applications characterized by the continuous operation or transitioning of the protection circuits. At the time of thermal designing, keep in mind that the current capability has negative characteristics to temperatures. (See Fig. 3) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 7/9 2011.03 - Rev.B BD3570FP/HFP, BD3571FP/HFP, BD3572FP/HFP, BD3573FP/HFP BD3574FP/HFP, BD3575FP/HFP ●Ordering Part Number Technical Note B D 3 5 7 4 H F P - T R ローム形名 Part number 3570：3.3V output no include SW 3571：5.0V output no include SW 3572：variable output no include SW 3573：3.3V output include SW 3574：5.0V output include SW 3575：variable output include SW Package FP ： TO252-3, TO252-5 HFP： HRP5 Packaging and forming specification E2: Embossed tape and reel (TO252-3,TO252-5) TR: Embossed tape and reel (HRP5) TO252-3 6.5±0.2 1.5±0.2 Tape C0.5 2.3±0.2 0.5±0.1 Embossed carrier tape 2000pcs E2 The direction is the 1pin of product is at the lower left when you hold +0.2 5.1 -0.1 Quantity Direction of feed FIN 5.5±0.2 9.5±0.5 ( reel on the left hand and you pull out the tape on the right hand ) 0.65 0.75 2.3±0.2 0.8 0.65 0.5±0.1 2.3±0.2 1.0±0.2 2.5 1 2 3 1.5 1pin Direction of feed (Unit : mm) Reel ∗ Order quantity needs to be multiple of the minimum quantity. TO252-5 6.5±0.2 +0.2 5.1 -0.1 2.3±0.2 C0.5 0.5±0.1 Tape Quantity Direction of feed Embossed carrier tape 2000pcs E2 The direction is the 1pin of product is at the lower left when you hold 1.5±0.2 FIN 5.5±0.2 9.5±0.5 ( reel on the left hand and you pull out the tape on the right hand ) 0.8 0.5±0.1 0.5 1.27 1.0±0.2 2.5 123 45 1.5 1pin Direction of feed (Unit : mm) Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/9 2011.03 - Rev.B BD3570FP/HFP, BD3571FP/HFP, BD3572FP/HFP, BD3573FP/HFP BD3574FP/HFP, BD3575FP/HFP Technical Note HRP5 9.395±0.125 (MAX 9.745 include BURR) 1.017±0.2 Tape 1.905±0.1 Embossed carrier tape 2000pcs TR direction the at right when you ( The on the leftishand1pin of product is thethe upperthe right hand hold ) reel and you pull out tape on 8.82 ± 0.1 (6.5) Quantity Direction of feed 0.835±0.2 1.523±0.15 10.54±0.13 8.0±0.13 (7.49) 1pin 1.2575 1 2 3 4 5 5.5° 4.5°+4.5° − +0.1 0.27 −0.05 1.72 0.73±0.1 0.08 S S 0.08±0.05 Direction of feed (Unit : mm) Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 9/9 2011.03 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A