0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
BD6095GU

BD6095GU

  • 厂商:

    ROHM(罗姆)

  • 封装:

  • 描述:

    BD6095GU - Mulitifunction Backlight LED Driver for Small LCD Panels (Charge Pump Type) - Rohm

  • 数据手册
  • 价格&库存
BD6095GU 数据手册
LED Drivers for LCD Backlights Mulitifunction Backlight LED Driver for Small LCD Panels (Charge Pump Type) BD6095GUL,BD6095GU No.11040EAT31 ●Description BD6095GUL/BD6095GU is “Intelligent LED Driver” that is the most suitable for the cellular phone. It has many functions that are needed to "the upper side" of the cellular phone. It has ALC function, that is “Low Power Consumption System” realized. It has “Contents Adaptive Interface” (External PWM control), that is “Low Power Consumption System” realized. It adopts the very thin CSP package that is the most suitable for the slim phone. ●Features 1) Total 5LEDs driver for LCD Backlight It can set maximum 25.6mA /ch by 128steps (Current DAC) for LCD Display. 3LEDs(LED1~LED3) are same controlled. Another 2LEDs(LED4~5) can be independent controlled. (Enable and Current setting) 2LEDs(LED4~5) can be attributed to “Main Group”. “Main Group” can be controlled by Auto Luminous Control (ALC) system. “Main Group” can be controlled by external PWM signal. 2) 1LED driver for Flash/Torch It can set maximum 120mA for Flash LED Driver. It has Flash mode and Torch mode, there can be changed by external pin or register. 3) Auto Luminous Control (ALC) Main backlight can be controlled by ambient brightness. Photo Diode, Photo Transistor, Photo IC(Linear/Logarithm) can be connected. Bias source for ambient light sensor, gain and offset adjustment are built in. LED driver current as ambient level can be customized. 4) 2ch Series Regulator (LDO) It has selectable output voltage by the register. LDO1,LDO2 : Iomax=150mA 5) Charge Pump DC/DC for LED driver It has x1/x1.33/x1.5/x2 mode that will be selected automatically. Soft start functions Over voltage protection (Auto-return type) Over current protection (Auto-return type) 6) Thermal shutdown (Auto-return type) 7) I2C BUS FS mode (max 400kHz) 2 8) VCSP50L3 (3.75mm , 0.55mmt max) Small and thin CSP package (BD6095GUL) 9) VCSP85H3 (3.75mm2, 1.0mmt max) Small and thin CSP package (BD6095GU) *This chip is not designed to protect itself against radioactive rays. *This material may be changed on its way to designing. *This material is not the official specification. ●Absolute Maximum Ratings (Ta=25 oC) Parameter Maximum voltage Power Dissipation Operating Temperature Range Storage Temperature Range Symbol VMAX Pd Topr Tstg Ratings 7 1500 -35 ~ +85 -55 ~ +150 Unit V mW o o C C note)Power dissipation deleting is 12.0mW/ oC, when it’s used in over 25 oC. (It’s deleting is on the board that is ROHM’s standard) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Operating conditions (VBAT≥VIO, Ta=-35~85 oC) Symbol VBAT VIO Ratrings 2.7~5.5 1.65~3.3 Unit V V Technical Note Parameter VBAT input voltage VIO pin voltage ●Electrical Characteristics (Unless otherwise specified, Ta=25°C, VBAT=3.6V, VIO=1.8V) Limits Parameter Symbol Unit Min. Typ. Max. 【Circuit Current】 VBAT Circuit current 1 VBAT Circuit current 2 VBAT Circuit current 3 VBAT Circuit current 4 VBAT Circuit current 5 VBAT Circuit current 6 VBAT Circuit current 7 VBAT Circuit current 8 【LED Driver】 LED current Step (Setup) LED current Step (At slope) LED current Step (Flash) White LED Maximum setup current Flash LED Maximum setup current LED1~5 current accuracy Flash LED current accuracy LED current Matching LED OFF Leak current 【DC/DC(Charge Pump)】 Maximum Output voltage Current Load Oscillator frequency Over Voltage Protection detect voltage Short Circuit current limit 【I C Input (SDA, SCL)】 LOW level input voltage HIGH level input voltage Hysteresis of Schmitt trigger input LOW level output voltage (SDA) at 3mA sink current Input current each I/O pin VIL VIH Vhys VOL lin 2 Condition IBAT1 IBAT2 IBAT3 IBAT4 IBAT5 IBAT6 IBAT7 IBAT8 - 0.1 0.5 90 61 83 93 124 0.25 1.0 3.0 150 65 94 104 136 1.0 μA μA μA mA mA mA mA mA RESETB=0V, VIO=0V RESETB=0V, VIO=1.8V LDO1=LDO2=ON, ILDO=0mA Other blocks=OFF DC/DC x1mode, ILED=60mA VBAT=3.7V, LED Vf=3.0V DC/DC x1.33mode, ILED=60mA VBAT=3.1V, LED Vf=3.0V DC/DC x1.5mode, ILED=60mA VBAT=2.9V, LED Vf=3.5V DC/DC x2mode, ILED=60mA VBAT=3.2V, LED Vf=4.0V Only ALC block ON ADCYC=0.5s setting Except sensor current LED1~5 LED1~5 LEDFL LED1~5 LEDFL ILED=15mA setting at VLED=1.0V ILED=60mA setting at VLED=1.0V Between LED1~5 at VLED=1.0V VLED=4.5V ILEDSTP1 ILEDSTP2 ILEDSTPFL IMAXWLED IMAXFLED IWLED IFLED ILEDMT ILKLED VoCP IOUT fosc OVP Ilim -7% -7% 4.65 0.8 -0.3 0.75 × VIO 0.05 × VIO 0 -3 -0.3 0.75 × VIO -3 128 256 32 25.6 120 15 60 5.1 1.0 125 +7% +7% 4 1.0 5.55 250 1.2 6.0 250 0.25 × VIO VBAT +0.3 0.3 3 0.25 × VIO VBAT +0.3 3 Step Step Step mA mA mA mA % μA V mA MHz V mA V V V V μA V V μA VBAT≥3.2V, VOUT=4V VOUT=0V Input voltage = 0.1×VIO~0.9×VIO 【RESETB】 LOW level input voltage HIGH level input voltage Input current each I/O pin VIL VIH Iin Input voltage = 0.1×VIO~0.9×VIO www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Electrical Characteristics (Unless otherwise specified, Ta=25°C, VBAT=3.6V, VIO=1.8V) Limits Parameter Symbol Unit Min. Typ. Max. 【Regulator (LDO1)】 1.164 1.261 1.455 1.552 1.746 2.134 2.328 2.425 2.522 2.619 2.716 2.813 2.910 3.007 3.104 3.201 1.164 1.261 1.455 1.552 1.746 2.134 2.328 2.425 2.522 2.619 2.716 2.813 2.910 3.007 3.104 3.201 1.20 1.30 1.50 1.60 1.80 2.20 2.40 2.50 2.60 2.70 2.80 2.90 3.00 3.10 3.20 3.30 0.05 10 10 65 200 1.0 1.20 1.30 1.50 1.60 1.80 2.20 2.40 2.50 2.60 2.70 2.80 2.90 3.00 3.10 3.20 3.30 0.05 10 10 65 200 1.0 1.236 1.339 1.545 1.648 1.854 2.266 2.472 2.575 2.678 2.781 2.884 2.987 3.090 3.193 3.296 3.399 150 0.1 60 60 400 1.5 1.236 1.339 1.545 1.648 1.854 2.266 2.472 2.575 2.678 2.781 2.884 2.987 3.090 3.193 3.296 3.399 150 0.1 60 60 400 1.5 V V V V V V V V V V V V V V V V mA V mV mV dB mA kΩ V V V V V V V V V V V V V V V V mA V mV mV dB mA kΩ Technical Note Condition Output voltage Vo1 Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Vo=1.8V VBAT=2.5V, Io=50mA, Vo=2.8V Io=1~150mA, Vo=1.8V VBAT=3.4~4.5V, Io=50mA, Vo=1.8V f=100Hz, Vin=200mVp-p, Vo=1.2V Io=50mA, BW=20Hz~20kHz Vo=0V Output Current Dropout Voltage Load stability Input voltage stability Ripple Rejection Ratio Short circuit current limit Discharge resister at OFF 【Regulator (LDO2)】 Io1 Vsat1 ΔVo11 ΔVo12 RR1 Ilim1 ROFF1 Output voltage Vo2 Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Io=50mA Vo=2.5V VBAT=2.5V, Io=50mA, Vo=2.8V Io=1~150mA, Vo=2.5V VBAT=3.4~4.5V, Io=50mA, Vo=2.5V f=100Hz, Vin=200mVp-p, Vo=1.2V Io=50mA, BW=20Hz~20kHz Vo=0V Output Current Dropout Voltage Load stability Input voltage stability Ripple Rejection Ratio Short circuit current limit Discharge resister at OFF Io2 Vsat2 Δvo21 Δvo22 RR2 Ilim2 ROFF2 www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Electrical Characteristics (Unless otherwise specified, Ta=25°C, VBAT=3.6V, VIO=1.8V) Limits Parameter Symbol Unit Min. Typ. Max. 【Sensor Interface】 2.850 SBIAS Output voltage VoS 2.470 SBIAS Output current SSENS Input range SBIAS Discharge resister at OFF ADC resolution ADC non-linearity error ADC differential non-linearity error SSENS Input impedance 【WPWMIN】 L level input voltage H level input voltage Input current PWM input minimum High pulse width 【GC1, GC2】 L level output voltage H level output voltage 【FLASHCNT】 L level input voltage H level input voltage Input current VILF VIHF IinF -0.3 1.4 3.6 0.3 VBAT +0.3 10 V V μA Vin=1.8V VOLS VOHS VoS -0.2 0.2 V V IOL=1mA IOH=1mA VILA VIHA IinA PWpwm -0.3 1.4 80 3.6 0.3 VBAT +0.3 10 V V μA μs Vin=1.8V IoS VISS ROFFS ADRES ADINL ADDNL RSSENS -3 -1 1 0 2.6 1.0 8 +3 +1 2.730 30 VoS x 255/256 1.5 V mA V kΩ bit LSB LSB MΩ Io=200μA Vo=3.0V 3.0 3.150 V Technical Note Condition Io=200μA www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Block Diagram / Application Circuit example Technical Note 1μF (6.3V) 1μF (6.3V) 1μF (6.3V) C1N C2N C1P C2P C3N VBAT VBATCP VBAT1 VBATLDO 10µF C3P Charge Pump x1 / x1.33 / x1.5 / x2 VOUT 2.2μF (6.3V) LED1 Charge Pump Mode Control OVP LED terminal voltage feedback LED2 LED3 Back Light LED4 VIO RESETB SCL LED5 SDA I/O Level Shift I2C interface Digital Control TSD LEDFL Flash WPWMIN FLASHCNT IREF To LED1~5 LEDFL VREF LDO1 BH1600FVC SBIAS 1 μF Vo selectable Io=150mA LDO1O 1μF LDO2 Vo selectable Io=150mA LDO2O 1μF SSENS GC1 GC2 Sensor I/F LED control SGND ALC LEDGND T3 (Open) CPGND Fig.1 Block Diagram / Application Circuit example www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. T4 (Open) T1 T2 5/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Pin Arrangement [Bottom View] Technical Note F T4 LDO1O SSENS VBAT1 SBIAS T3 E VBATLDO LDO2O GC2 GC1 SGND VIO D WPWMIN LED1 FLASHCNT SDA SCL C1N C LED3 LED2 RESETB C1P C2N B LED4 LED5 LEDGND VOUT VBATCP C2P A T1 LEDFL CPGND C3N C3P T2 1 2 3 4 5 6 Index Total: 35 balls www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Package ●BD6095GUL VCSP50L3 SIZE : 3.75mm A ball pitch : 0.5mm Height : 0.55mm max Technical Note BD6095 Lot No. ( Unit : mm ) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 7/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note ●BD6095GU VCSP85H3 SIZE : 3.75mm A ball pitch : 0.5mm Height : 1.0mm max D6095 Lot No. ( Unit : mm ) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Pin Functions No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 ※ Technical Note Ball No. B5 F4 E1 A1 A6 F6 F1 E6 C4 D4 D5 A3 B3 D6 C5 C6 B6 A4 A5 B4 F2 E2 D2 C2 C1 B1 B2 A2 F5 F3 E4 E3 E5 D1 D3 Pin Name VBATCP VBAT1 VBATLDO T1 T2 T3 T4 VIO RESETB SDA SCL CPGND LEDGND C1N C1P C2N C2P C3N C3P VOUT LDO1O LDO2O LED1 LED2 LED3 LED4 LED5 LEDFL SBIAS SSENS GC1 GC2 SGND WPWMIN FLASHCNT I/O I I O O I I/O I I/O I/O I/O I/O I/O I/O O O O I I I I I I O I O O I I ESD Diode For For Power Ground GND GND GND VBAT GND VBAT GND VBAT GND VBAT GND VBAT GND VBAT GND VBAT GND VBAT GND VBAT VBAT VBAT GND GND VBAT GND GND VBAT GND GND GND VBAT GND VBAT GND GND GND GND GND GND GND VBAT GND VBAT GND VBAT GND VBAT GND VBAT VBAT GND VBAT GND Functions Power supply for charge pump Power supply Power supply for LDO Test Input Pin (short to Ground) Test Input Pin (short to Ground) Test Output Pin (Open) Test Output Pin (Open) Power supply for I/O and Digital Reset input (L: reset, H: reset cancel) I2C data input / output I2C clock input Ground Ground Charge Pump capacitor is connected Charge Pump capacitor is connected Charge Pump capacitor is connected Charge Pump capacitor is connected Charge Pump capacitor is connected Charge Pump capacitor is connected Charge Pump output pin LDO1 output pin LDO2 output pin LED cathode connection 1 LED cathode connection 2 LED cathode connection 3 LED cathode connection 4 LED cathode connection 5 LED cathode connection for Flash Bias output for the Ambient Light Sensor Ambient Light Sensor input Ambient Light Sensor gain control output 1 Ambient Light Sensor gain control output 2 Ground External PWM input for Back Light External enable for Flash Equivalent Circuit A A A S S M N C H I H B B F G F G F G A Q Q E E E E E E Q N X X B L L The LED terminal that isn't used is to short-circuit to the ground. But, the setup of a register concerned with LED that isn't used is prohibited. Total: 35 Pin www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 9/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Equivalent Circuit Technical Note A B VBAT C VBAT E F VBAT G H VBAT VIO I VBAT VIO J VBAT VIO K VIO VIO L VBAT VBAT M VBAT VBAT N VBAT O VBAT P VBAT VBAT Q VBAT VBAT R VBAT VBAT S VBAT VBAT T VIO VBAT X VoS VBAT www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 10/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●I2C BUS format The writing/reading operation is based on the I2C slave standard. ・Slave address A7 A6 A5 A4 A3 A2 1 1 1 0 1 1 Technical Note A1 0 R/W 1/0 ・Bit Transfer SCL transfers 1-bit data during H. SCL cannot change signal of SDA during H at the time of bit transfer. If SDA changes while SCL is H, START conditions or STOP conditions will occur and it will be interpreted as a control signal. SDA SCL SDA a state of stability: SDA It can change Data are effective ・START and STOP condition When SDA and SCL are H, data is not transferred on the I2C- bus. This condition indicates, if SDA changes from H to L while SCL has been H, it will become START (S) conditions, and an access start, if SDA changes from L to H while SCL has been H, it will become STOP (P) conditions and an access end. SDA SCL S START condition P STOP condition ・Acknowledge It transfers data 8 bits each after the occurrence of START condition. A transmitter opens SDA after transfer 8bits data, and a receiver returns the acknowledge signal by setting SDA to L. DATA OUTPUT BY TRANSMITTER not acknowledge DATA OUTPUT BY RECEIVER acknowledge SCL 1 2 8 clock pulse for acknowledgement 9 S START condition www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 11/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note ・Writing protocol A register address is transferred by the next 1 byte that transferred the slave address and the write-in command. The 3rd byte writes data in the internal register written in by the 2nd byte, and after 4th byte or, the increment of register address is carried out automatically. However, when a register address turns into the last address, it is set to 00h by the next transmission. After the transmission end, the increment of the address is carried out. *1 *1 S X X X X X X X 0 A A 7 A 6 A 5 A 4 A 3 A 2 A 1 A 0 A D7 D6 D5 D4 D3 D2 D1 D0 A slave address R /W=0(write) from master to slave from slave to master register address D ATA D7 D 6 D 5 D 4 D 3 D 2 D1 D0 A P DATA register address increment A =acknowledge(SD A LOW) A =not acknowledge(SDA HIGH) S=START condition P=STOP condition *1: Write Timing register address increment ・Reading protocol It reads from the next byte after writing a slave address and R/W bit. The register to read considers as the following address accessed at the end, and the data of the address that carried out the increment is read after it. If an address turns into the last address, the next byte will read out 00h. After the transmission end, the increment of the address is carried out. SXXXXXXX slave address R/W=1(read) 1 A D7 D6 D5 D4 D3 D2 D1 D0 A DATA register address increment A=acknowledge(SDA LOW) A=not acknowledge(SDA HIGH) S=START condition P=STOP condition D7 D6 D5 D4 D3 D2 D1 D0 A P DATA register address increment from master to slave from slave to master ・Multiple reading protocols After specifying an internal address, it reads by repeated START condition and changing the data transfer direction. The data of the address that carried out the increment is read after it. If an address turns into the last address, the next byte will read out 00h. After the transmission end, the increment of the address is carried out. S X X X X X X X 0 A A7 A6 A5 A4 A3 A2 A1 A0 A Sr X X X X X X X 1 A slave address R/W=0(write) register address slave address R/W=1(read) D7 D6 D5 D4 D3D2 D1D0 A DATA register address increment from master to slave from slave to master D7D6 D5D4D3D2D1D0 A P DATA register address increment A=acknowledge(SDA LOW) A=not acknowledge(SDA HIGH) S=START condition P=STOP condition Sr=repeated START condition As for reading protocol and multiple reading protocols, please do A(not acknowledge) after doing the final reading operation. It stops with read when ending by A(acknowledge), and SDA stops in the state of Low when the reading data of that time is 0. However, this state returns usually when SCL is moved, data is read, and A(not acknowledge) is done. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 12/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Timing diagram SDA Technical Note t BUF t LOW t SU;DAT t HD;STA SCL t SU;STO P S t HD;STA S t HD;DAT t HIGH Sr t SU;STA ●Electrical Characteristics(Unless otherwise specified, Ta=25 oC, VBAT=3.6V, VIO=1.8V) Standard-mode Parameter Symbol Min. Typ. Max. 【I2C BUS format】 Min. 0 1.3 0.6 0.6 0.6 0 100 0.6 1.3 Fast-mode Typ. - Max. 400 0.9 - Unit SCL clock frequency LOW period of the SCL clock HIGH period of the SCL clock Hold time (repeated) START condition After this period, the first clock is generated Set-up time for a repeated START condition Data hold time Data set-up time Set-up time for STOP condition Bus free time between a STOP and START condition fSCL tLOW tHIGH tHD;STA tSU;STA tHD;DAT tSU;DAT tSU;STO tBUF 0 4.7 4.0 4.0 4.7 0 250 4.0 4.7 - 100 3.45 - kHz μs μs μs μs μs ns μs μs www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 13/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Register List Address W/R Register data D7 FLASHEN D6 LED5MD(1) TORCHEN IMLED(6) ISLED(6) D5 LED5MD(0) SLEDEN IMLED(5) ISLED(5) D4 LED4MD MLEDEN IMLED(4) ISLED(4) IFTLED(4) IFFLED(4) D3 IMLED(3) ISLED(3) IFTLED(3) IFFLED(3) D2 WPWMEN IMLED(2) ISLED(2) IFTLED(2) IFFLED(2) D1 ALCEN LDO2EN IMLED(1) ISLED(1) IFTLED(1) IFFLED(1) D0 SFTRST MLEDMD LDO1EN IMLED(0) ISLED(0) IFTLED(0) IFFLED(0) LDO1VSEL(0) TLH(0) SBIASON SGAIN(0) AMB(0) IU0(0) IU1(0) IU2(0) IU3(0) IU4(0) IU5(0) IU6(0) IU7(0) IU8(0) IU9(0) IUA(0) IUB(0) IUC(0) IUD(0) IUE(0) IUF(0) Technical Note Function 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh W W W W W W W W W W W R W W W W W W W W W W W W W W W W Software Reset LED, ALC Control Power Control “Main Group” LED Current Setting at non-ALC mode “Sub Group” LED Current Setting Flash LED “Torch mode” Current Setting Flash LED “Flash mode” Current Setting LDO1, LDO2 Vout Setting Main Current transition ALC mode setting ADC Data adjustment Ambient level Main Current at Ambient level 0h Main Current at Ambient level 1h Main Current at Ambient level 2h Main Current at Ambient level 3h Main Current at Ambient level 4h Main Current at Ambient level 5h Main Current at Ambient level 6h Main Current at Ambient level 7h Main Current at Ambient level 8h Main Current at Ambient level 9h Main Current at Ambient level Ah Main Current at Ambient level Bh Main Current at Ambient level Ch Main Current at Ambient level Dh Main Current at Ambient level Eh Main Current at Ambient level Fh LDO2VSEL(3) LDO2VSEL(2) LDO2VSEL(1) LDO2VSEL(0) LDO1VSEL(3) LDO1VSEL(2) LDO1VSEL(1) THL(3) ADCYC(1) SOFS(3) THL(2) ADCYC(0) SOFS(2) IU0(6) IU1(6) IU2(6) IU3(6) IU4(6) IU5(6) IU6(6) IU7(6) IU8(6) IU9(6) IUA(6) IUB(6) IUC(6) IUD(6) IUE(6) IUF(6) THL(1) GAIN(1) SOFS(1) IU0(5) IU1(5) IU2(5) IU3(5) IU4(5) IU5(5) IU6(5) IU7(5) IU8(5) IU9(5) IUA(5) IUB(5) IUC(5) IUD(5) IUE(5) IUF(5) THL(0) GAIN(0) SOFS(0) IU0(4) IU1(4) IU2(4) IU3(4) IU4(4) IU5(4) IU6(4) IU7(4) IU8(4) IU9(4) IUA(4) IUB(4) IUC(4) IUD(4) IUE(4) IUF(4) TLH(3) STYPE SGAIN(3) AMB(3) IU0(3) IU1(3) IU2(3) IU3(3) IU4(3) IU5(3) IU6(3) IU7(3) IU8(3) IU9(3) IUA(3) IUB(3) IUC(3) IUD(3) IUE(3) IUF(3) TLH(2) VSB SGAIN(2) AMB(2) IU0(2) IU1(2) IU2(2) IU3(2) IU4(2) IU5(2) IU6(2) IU7(2) IU8(2) IU9(2) IUA(2) IUB(2) IUC(2) IUD(2) IUE(2) IUF(2) TLH(1) MDCIR SGAIN(1) AMB(1) IU0(1) IU1(1) IU2(1) IU3(1) IU4(1) IU5(1) IU6(1) IU7(1) IU8(1) IU9(1) IUA(1) IUB(1) IUC(1) IUD(1) IUE(1) IUF(1) Input "0” for "-". Prohibit to accessing the address that isn’t mentioned. The time indicated by register explanation is the TYP time made by dividing of the built-in OSC. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 14/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Register Map Address 00h Address 00h Initial Value Technical Note < Software Reset > R/W W 00h Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 SFTRST 0 Bit [7:1] : Bit0 : (Not used) SFTRST Software Reset Command “0” : Reset cancel “1” : Reset (All register initializing) Refer to “The explanation of Reset” for detail. Address 01h Address 01h Initial Value < LED, ALC Control > R/W W 00h Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 WPWMEN 0 Bit1 ALCEN 0 Bit0 MLEDMD 0 LED5MD(1) LED5MD(0) LED4MD 0 0 0 Bit7 : (Not used) Bit [6:5] : LED5MD(1:0) LED5 Group Select (Main/Sub/OFF) “00” : LED5 OFF “01” : reserved “10” : LED5 “Sub Group” “11” : LED5 “Main Group” Refer to “The explanation of LED Driver” for detail. Bit4 : LED4MD LED4 Group Select (Main/Sub) “0” : LED4 “Sub Group” “1” : LED4 “Main Group” Refer to “The explanation of LED Driver” for detail. (Not used) WPWMEN External PWM Input “WPWMIN” terminal Enable Control (Valid/Invalid) “0” : WPWMIN input invalid “1” : WPWMIN input valid Refer to “(11) Current Adjustment” of “The explanation of ALC” for detail. ALCEN ALC Function Control (ON/OFF) “0” : ALC function OFF “1” : ALC function ON Refer to “(1) Auto Luminous Control ON/OFF” of “The explanation of ALC” for detail. MLEDMD “Main Group” LED Mode Select (Non ALC / with ALC) “0” : Non ALC mode “1” : ALC mode Refer to “(1) Auto Luminous Control ON/OFF” of “The explanation of ALC” for detail. Bit3 : Bit2 : Bit1 : Bit0 : www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 15/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 02h Address 02h Initial Value < Power Control > R/W W 00h Bit7 Bit6 Bit5 SLEDEN 0 Bit4 MLEDEN 0 Bit3 Bit2 Bit1 LDO2EN 0 Bit0 LDO1EN 0 FLASHEN TORCHEN 0 0 Bit [7:6] : FLASHEN, TORCHEN LEDFL Control (Flash ON / Torch ON / OFF) (At FLASHCNT=H) "FLASHCNT" means external pin. (At FLASHCNT=L) “00” : “01” : “10” : “11” : LEDFL: OFF, LEDFL: Torch mode ON, LEDFL: Flash mode ON, reserved Flash mode ON Flash mode ON Flash mode ON For Torch/Flash, refer to “Flash LED Current Setting” (address 05h, 06h) At FLASHCNT=H, even if RESETB=L, the Flash mode becomes ON, and LED is turned on. But, the setup of LED current becomes the minimum setting in this case. (Because the setting of LED current is reset at the time of RESETB=L.) Refer to “The explanation of LED Driver” for detail. Bit5 : SLEDEN Sub Group LED Control (ON/OFF) “0” : “Sub Group” LED OFF “1” : “Sub Group” LED ON MLEDEN Main Group LED Control (ON/OFF) “0” : “Main Group” LED OFF “1” : “Main Group” LED ON Bit4 : Bit [3:2] : (Not used) Bit1 : LDO2EN LDO2 Control (ON/OFF) “0” : LDO2 OFF “1” : LDO2 ON LDO1EN LDO1 Control (ON/OFF) “0” : LDO1 OFF “1” : LDO1 ON Bit0 : www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 16/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 03h Address 03h Initial Value < “Main Group” LED Current Setting at non-ALC mode > R/W W 00h Bit7 Bit6 IMLED(6) 0 Bit5 IMLED(5) 0 Bit4 IMLED(4) 0 Bit3 IMLED(3) 0 Bit2 IMLED(2) 0 Bit1 IMLED(1) 0 Bit0 IMLED(0) 0 Bit7 : (Not used) Main Group LED Current Setting at non-ALC mode 0.2 mA 0.4 mA 0.6 mA 0.8 mA 1.0 mA 1.2 mA 1.4 mA 1.6 mA 1.8 mA 2.0 mA 2.2 mA 2.4 mA 2.6 mA 2.8 mA 3.0 mA 3.2 mA 3.4 mA 3.6 mA 3.8 mA 4.0 mA 4.2 mA 4.4 mA 4.6 mA 4.8 mA 5.0 mA 5.2 mA 5.4 mA 5.6 mA 5.8 mA 6.0 mA 6.2 mA 6.4 mA 6.6 mA 6.8 mA 7.0 mA 7.2 mA 7.4 mA 7.6 mA 7.8 mA 8.0 mA 8.2 mA 8.4 mA 8.6 mA 8.8 mA 9.0 mA 9.2 mA 9.4 mA 9.6 mA 9.8 mA 10.0 mA 10.2 mA 10.4 mA 10.6 mA 10.8 mA 11.0 mA 11.2 mA 11.4 mA 11.6 mA 11.8 mA 12.0 mA 12.2 mA 12.4 mA 12.6 mA 12.8 mA “1000000” : “1000001” : “1000010” : “1000011” : “1000100” : “1000101” : “1000110” : “1000111” : “1001000” : “1001001” : “1001010” : “1001011” : “1001100” : “1001101” : “1001110” : “1001111” : “1010000” : “1010001” : “1010010” : “1010011” : “1010100” : “1010101” : “1010110” : “1010111” : “1011000” : “1011001” : “1011010” : “1011011” : “1011100” : “1011101” : “1011110” : “1011111” : “1100000” : “1100001” : “1100010” : “1100011” : “1100100” : “1100101” : “1100110” : “1100111” : “1101000” : “1101001” : “1101010” : “1101011” : “1101100” : “1101101” : “1101110” : “1101111” : “1110000” : “1110001” : “1110010” : “1110011” : “1110100” : “1110101” : “1110110” : “1110111” : “1111000” : “1111001” : “1111010” : “1111011” : “1111100” : “1111101” : “1111110” : “1111111” : 13.0 mA 13.2 mA 13.4 mA 13.6 mA 13.8 mA 14.0 mA 14.2 mA 14.4 mA 14.6 mA 14.8 mA 15.0 mA 15.2 mA 15.4 mA 15.6 mA 15.8 mA 16.0 mA 16.2 mA 16.4 mA 16.6 mA 16.8 mA 17.0 mA 17.2 mA 17.4 mA 17.6 mA 17.8 mA 18.0 mA 18.2 mA 18.4 mA 18.6 mA 18.8 mA 19.0 mA 19.2 mA 19.4 mA 19.6 mA 19.8 mA 20.0 mA 20.2 mA 20.4 mA 20.6 mA 20.8 mA 21.0 mA 21.2 mA 21.4 mA 21.6 mA 21.8 mA 22.0 mA 22.2 mA 22.4 mA 22.6 mA 22.8 mA 23.0 mA 23.2 mA 23.4 mA 23.6 mA 23.8 mA 24.0 mA 24.2 mA 24.4 mA 24.6 mA 24.8 mA 25.0 mA 25.2 mA 25.4 mA 25.6 mA Bit [6:0] : IMLED(6:0) “0000000” : “0000001” : “0000010” : “0000011” : “0000100” : “0000101” : “0000110” : “0000111” : “0001000” : “0001001” : “0001010” : “0001011” : “0001100” : “0001101” : “0001110” : “0001111” : “0010000” : “0010001” : “0010010” : “0010011” : “0010100” : “0010101” : “0010110” : “0010111” : “0011000” : “0011001” : “0011010” : “0011011” : “0011100” : “0011101” : “0011110” : “0011111” : “0100000” : “0100001” : “0100010” : “0100011” : “0100100” : “0100101” : “0100110” : “0100111” : “0101000” : “0101001” : “0101010” : “0101011” : “0101100” : “0101101” : “0101110” : “0101111” : “0110000” : “0110001” : “0110010” : “0110011” : “0110100” : “0110101” : “0110110” : “0110111” : “0111000” : “0111001” : “0111010” : “0111011” : “0111100” : “0111101” : “0111110” : “0111111” : www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 17/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 04h Address 04h Initial Value < “Sub Group” LED Current Setting > R/W W 00h Bit7 Bit6 ISLED(6) 0 Bit5 ISLED(5) 0 Bit4 ISLED(4) 0 Bit3 ISLED(3) 0 Bit2 ISLED(2) 0 Bit1 ISLED(1) 0 Bit0 ISLED(0) 0 Bit7 : (Not used) Sub Group LED Current Setting 0.2 mA 0.4 mA 0.6 mA 0.8 mA 1.0 mA 1.2 mA 1.4 mA 1.6 mA 1.8 mA 2.0 mA 2.2 mA 2.4 mA 2.6 mA 2.8 mA 3.0 mA 3.2 mA 3.4 mA 3.6 mA 3.8 mA 4.0 mA 4.2 mA 4.4 mA 4.6 mA 4.8 mA 5.0 mA 5.2 mA 5.4 mA 5.6 mA 5.8 mA 6.0 mA 6.2 mA 6.4 mA 6.6 mA 6.8 mA 7.0 mA 7.2 mA 7.4 mA 7.6 mA 7.8 mA 8.0 mA 8.2 mA 8.4 mA 8.6 mA 8.8 mA 9.0 mA 9.2 mA 9.4 mA 9.6 mA 9.8 mA 10.0 mA 10.2 mA 10.4 mA 10.6 mA 10.8 mA 11.0 mA 11.2 mA 11.4 mA 11.6 mA 11.8 mA 12.0 mA 12.2 mA 12.4 mA 12.6 mA 12.8 mA “1000000” : “1000001” : “1000010” : “1000011” : “1000100” : “1000101” : “1000110” : “1000111” : “1001000” : “1001001” : “1001010” : “1001011” : “1001100” : “1001101” : “1001110” : “1001111” : “1010000” : “1010001” : “1010010” : “1010011” : “1010100” : “1010101” : “1010110” : “1010111” : “1011000” : “1011001” : “1011010” : “1011011” : “1011100” : “1011101” : “1011110” : “1011111” : “1100000” : “1100001” : “1100010” : “1100011” : “1100100” : “1100101” : “1100110” : “1100111” : “1101000” : “1101001” : “1101010” : “1101011” : “1101100” : “1101101” : “1101110” : “1101111” : “1110000” : “1110001” : “1110010” : “1110011” : “1110100” : “1110101” : “1110110” : “1110111” : “1111000” : “1111001” : “1111010” : “1111011” : “1111100” : “1111101” : “1111110” : “1111111” : 13.0 mA 13.2 mA 13.4 mA 13.6 mA 13.8 mA 14.0 mA 14.2 mA 14.4 mA 14.6 mA 14.8 mA 15.0 mA 15.2 mA 15.4 mA 15.6 mA 15.8 mA 16.0 mA 16.2 mA 16.4 mA 16.6 mA 16.8 mA 17.0 mA 17.2 mA 17.4 mA 17.6 mA 17.8 mA 18.0 mA 18.2 mA 18.4 mA 18.6 mA 18.8 mA 19.0 mA 19.2 mA 19.4 mA 19.6 mA 19.8 mA 20.0 mA 20.2 mA 20.4 mA 20.6 mA 20.8 mA 21.0 mA 21.2 mA 21.4 mA 21.6 mA 21.8 mA 22.0 mA 22.2 mA 22.4 mA 22.6 mA 22.8 mA 23.0 mA 23.2 mA 23.4 mA 23.6 mA 23.8 mA 24.0 mA 24.2 mA 24.4 mA 24.6 mA 24.8 mA 25.0 mA 25.2 mA 25.4 mA 25.6 mA Bit [6:0] : ISLED(6:0) “0000000” : “0000001” : “0000010” : “0000011” : “0000100” : “0000101” : “0000110” : “0000111” : “0001000” : “0001001” : “0001010” : “0001011” : “0001100” : “0001101” : “0001110” : “0001111” : “0010000” : “0010001” : “0010010” : “0010011” : “0010100” : “0010101” : “0010110” : “0010111” : “0011000” : “0011001” : “0011010” : “0011011” : “0011100” : “0011101” : “0011110” : “0011111” : “0100000” : “0100001” : “0100010” : “0100011” : “0100100” : “0100101” : “0100110” : “0100111” : “0101000” : “0101001” : “0101010” : “0101011” : “0101100” : “0101101” : “0101110” : “0101111” : “0110000” : “0110001” : “0110010” : “0110011” : “0110100” : “0110101” : “0110110” : “0110111” : “0111000” : “0111001” : “0111010” : “0111011” : “0111100” : “0111101” : “0111110” : “0111111” : www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 18/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 05h Address 05h Initial Value < Flash LED “Torch mode” Current Setting > R/W W 00h Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 IFTLED(4) IFTLED(3) IFTLED(2) IFTLED(1) IFTLED(0) 0 0 0 0 0 Bit [7:5] : (Not used) Bit [4:0] : IFTLED(4:0) “00000” : “00001” : “00010” : “00011” : “00100” : “00101” : “00110” : “00111” : “01000” : “01001” : “01010” : “01011” : “01100” : “01101” : “01110” : “01111” : “10000” : “10001” : “10010” : “10011” : “10100” : “10101” : “10110” : “10111” : “11000” : “11001” : “11010” : “11011” : “11100” : “11101” : “11110” : “11111” : “Torch mode” of LEDFL Current Setting 3.75 mA 7.50 mA 11.25 mA 15.00 mA 18.75 mA 22.50 mA 26.25 mA 30.00 mA 33.75 mA 37.50 mA 41.25 mA 45.00 mA 48.75 mA 52.50 mA 56.25 mA 60.00 mA 63.75 mA 67.50 mA 71.25 mA 75.00 mA 78.75 mA 82.50 mA 86.25 mA 90.00 mA 93.75 mA 97.50 mA 101.25 mA 105.00 mA 108.75 mA 112.50 mA 116.25 mA 120.00 mA (Initial value) * LED Current : 120 x 1/32 mA Step ( =3.75 mA Step) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 19/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 06h Address 06h Initial Value < Flash LED “Flash mode” Current Setting > R/W W 00h Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 IFFLED(4) IFFLED(3) IFFLED(2) IFFLED(1) IFFLED(0) 0 0 0 0 0 Bit [7:5] : (Not used) Bit [4:0] : IFFLED(4:0) “00000” : “00001” : “00010” : “00011” : “00100” : “00101” : “00110” : “00111” : “01000” : “01001” : “01010” : “01011” : “01100” : “01101” : “01110” : “01111” : “10000” : “10001” : “10010” : “10011” : “10100” : “10101” : “10110” : “10111” : “11000” : “11001” : “11010” : “11011” : “11100” : “11101” : “11110” : “11111” : “Flash mode” of LEDFL Current Setting 3.75 mA 7.50 mA 11.25 mA 15.00 mA 18.75 mA 22.50 mA 26.25 mA 30.00 mA 33.75 mA 37.50 mA 41.25 mA 45.00 mA 48.75 mA 52.50 mA 56.25 mA 60.00 mA 63.75 mA 67.50 mA 71.25 mA 75.00 mA 78.75 mA 82.50 mA 86.25 mA 90.00 mA 93.75 mA 97.50 mA 101.25 mA 105.00 mA 108.75 mA 112.50 mA 116.25 mA 120.00 mA (Initial value) * LED Current : 120 x 1/32 mA Step ( =3.75 mA Step) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 20/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 07h Address 07h Initial Value < LDO1 Vout Control, LDO2 Vout Control > R/W W 74h Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 LDO2VSEL(3)LDO2VSEL(2)LDO2VSEL(1)LDO2VSEL(0)LDO1VSEL(3)LDO1VSEL(2)LDO1VSEL(1)LDO1VSEL(0) 0 1 1 1 0 1 0 0 Bit [7:4] : LDO2VSEL(3:0) “0000” : “0001” : “0010” : “0011” : “0100” : “0101” : “0110” : “0111” : “1000” : “1001” : “1010” : “1011” : “1100” : “1101” : “1110” : “1111” : 1.20 V 1.30 V 1.50 V 1.60 V 1.80 V 2.20 V 2.40 V 2.50 V 2.60 V 2.70 V 2.80 V 2.90 V 3.00 V 3.10 V 3.20 V 3.30 V LDO2 Output Voltage Control (Initial value) Bit [3:0] : LDO1VSEL(3:0) LDO1 Output Voltage Control “0000” : 1.20 V “0001” : 1.30 V “0010” : 1.50 V “0011” : 1.60 V “0100” : 1.80 V (Initial value) “0101” : 2.20 V “0110” : 2.40 V “0111” : 2.50 V “1000” : 2.60 V “1001” : 2.70 V “1010” : 2.80 V “1011” : 2.90 V “1100” : 3.00 V “1101” : 3.10 V “1110” : 3.20 V “1111” : 3.30 V www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 21/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 08h Address 08h Initial Value < Main Current transition > R/W W C7h Bit7 THL(3) 1 Bit6 THL(2) 1 Bit5 THL(1) 0 Bit4 THL(0) 0 Bit3 TLH(3) 0 Bit2 TLH(2) 1 Bit1 TLH(1) 1 Bit0 TLH(0) 1 Bit [7:4] : THL(3:0) Main LED current Down transition per 0.2mA step “0000” : 0.256 ms “0001” : 0.512 ms “0010” : 1.024 ms “0011” : 2.048 ms “0100” : 4.096 ms “0101” : 8.192 ms “0110” : 16.38 ms “0111” : 32.77 ms “1000” : 65.54 ms “1001” : 131.1 ms “1010” : 196.6 ms “1011” : 262.1 ms “1100” : 327.7 ms (Initial value) “1101” : 393.2 ms “1110” : 458.8 ms “1111” : 524.3 ms Setting time is counted based on the switching frequency of Charge Pump. The above value becomes the value of the Typ (1MHz) time. Refer to “(9) Slope Process” of “The explanation of ALC” for detail. Bit [3:0] : TLH(3:0) Main LED current Up transition per 0.2mA step “0000” : 0.256 ms “0001” : 0.512 ms “0010” : 1.024 ms “0011” : 2.048 ms “0100” : 4.096 ms “0101” : 8.192 ms “0110” : 16.38 ms “0111” : 32.77 ms (Initial value) “1000” : 65.54 ms “1001” : 131.1 ms “1010” : 196.6 ms “1011” : 262.1 ms “1100” : 327.7 ms “1101” : 393.2 ms “1110” : 458.8 ms “1111” : 524.3 ms Setting time is counted based on the switching frequency of Charge Pump. The above value becomes the value of the Typ (1MHz) time. Refer to “(9) Slope Process” of “The explanation of ALC” for detail. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 22/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 0Bh Address 0Bh Initial Value < ALC mode setting > R/W W 81h Bit7 Bit6 Bit5 GAIN(1) 0 Bit4 GAIN(0) 0 Bit3 STYPE 0 Bit2 VSB 0 Bit1 MDCIR 0 Bit0 SBIASON 1 ADCYC(1) ADCYC(0) 1 0 Bit [7:6] : ADCYC(1:0) ADC Measurement Cycle “00” : 0.52 s “01” : 1.05 s “10” : 1.57 s (Initial value) “11” : 2.10 s Refer to “(4) A/D conversion” of “The explanation of ALC” for detail. Bit [5:4] : GAIN(1:0) Sensor Gain Switching Function Control (This is effective only at STYPE=“0”.) “00” : Auto Change (Initial value) “01” : High “10” : Low “11” : Fixed Refer to “(3) Gain control” of “The explanation of ALC” for detail. Bit3 : STYPE Ambient Light Sensor Type Select (Linear/Logarithm) “0” : For Linear sensor (Initial value) “1” : For Log sensor Refer to “(7) Ambient level detection” of “The explanation of ALC” for detail. VSB SBIAS Output Voltage Control “0” : SBIAS output voltage 3.0V (Initial value) “1” : SBIAS output voltage 2.6V Refer to “(2) I/V conversion” of “The explanation of ALC” for detail. MDCIR LED Current Reset Select by Mode Change “0” : LED current non-reset when mode change (Initial value) “1” : LED current reset when mode change Refer to “(10) LED current reset when mode change” of “The explanation of ALC” for detail. SBIASON SBIAS Control (ON/OFF) “0” : Measurement cycle synchronous “1” : Usually ON (at ALCEN=1) (Initial value) Refer to “(4) A/D conversion” of “The explanation of ALC” for detail. Bit2 : Bit1 : Bit0 : www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 23/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 0Ch Address 0Ch Initial Value < ADC Data adjustment > R/W W 00h Bit7 SOFS(3) 0 Bit6 SOFS(2) 0 Bit5 SOFS(1) 0 Bit4 SOFS(0) 0 Bit3 SGAIN(3) 0 Bit2 SGAIN(2) 0 Bit1 SGAIN(1) 0 Bit0 SGAIN(0) 0 Bit [7:4] : SOFS(3:0) “1000” : “1001” : “1010” : “1011” : “1100” : “1101” : “1110” : “1111” : “0000” : “0001” : “0010” : “0011” : “0100” : “0101” : “0110” : “0111” : AD Data Offset Adjustment -8 LSB -7 LSB -6 LSB -5 LSB -4 LSB -3 LSB -2 LSB -1 LSB non-adjust +1 LSB +2 LSB +3 LSB +4 LSB +5 LSB +6 LSB +7 LSB Offset adjust is performed to ADC data. Refer to “(5) ADC data Gain/offset adjustment” of “The explanation of ALC” for detail. Bit [3:0] : SGAIN(3:0) “1000” : “1001” : “1010” : “1011” : “1100” : “1101” : “1110” : “1111” : “0000” : “0001” : “0010” : “0011” : “0100” : “0101” : “0110” : “0111” : AD Data Gain Adjustment reserved reserved -37.50% -31.25% -25.00% -18.75% -12.50% -6.25% non-adjust +6.25% +12.50% +18.75% +25.00% +31.25% +37.50% reserved Gain adjust is performed to ADC data. The data after adjustment are round off by 8-bit data. Refer to “(5) ADC data Gain/offset adjustment” of “The explanation of ALC” for detail. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 24/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 0Dh Address 0Dh Initial Value < Ambient level (Read Only) > R/W R Bit7 Bit6 Bit5 Bit4 Bit3 AMB(3) Bit2 AMB(2) Bit1 AMB(1) Bit0 AMB(0) - Bit [7:4] : (Not used) Bit [3:0] : AMB(3:0) “0000” : “0001” : “0010” : “0011” : “0100” : “0101” : “0110” : “0111” : “1000” : “1001” : “1010” : “1011” : “1100” : “1101” : “1110” : “1111” : Ambient Level 0h 1h 2h 3h 4h 5h 6h 7h 8h 9h Ah Bh Ch Dh Eh Fh The data can be read through I2C. Refer to “(7) Ambient level detection” of “The explanation of ALC” for detail. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 25/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Address 0Eh~1Dh < Main Current at Ambient level 0h~Fh > Address 0Eh~1Dh Initial Value R/W W Bit7 Bit6 IU*(6) Bit5 IU*(5) Bit4 IU*(4) Bit3 IU*(3) Bit2 IU*(2) Bit1 IU*(1) Bit0 IU*(0) Refer to after page for initial table. “*” means 0~F. Bit7 : (Not used) Main Current at Ambient Level for 0h~Fh “0000000” : “0000001” : “0000010” : “0000011” : “0000100” : “0000101” : “0000110” : “0000111” : “0001000” : “0001001” : “0001010” : “0001011” : “0001100” : “0001101” : “0001110” : “0001111” : “0010000” : “0010001” : “0010010” : “0010011” : “0010100” : “0010101” : “0010110” : “0010111” : “0011000” : “0011001” : “0011010” : “0011011” : “0011100” : “0011101” : “0011110” : “0011111” : “0100000” : “0100001” : “0100010” : “0100011” : “0100100” : “0100101” : “0100110” : “0100111” : “0101000” : “0101001” : “0101010” : “0101011” : “0101100” : “0101101” : “0101110” : “0101111” : “0110000” : “0110001” : “0110010” : “0110011” : “0110100” : “0110101” : “0110110” : “0110111” : “0111000” : “0111001” : “0111010” : “0111011” : “0111100” : “0111101” : “0111110” : “0111111” : 0.2 mA 0.4 mA 0.6 mA 0.8 mA 1.0 mA 1.2 mA 1.4 mA 1.6 mA 1.8 mA 2.0 mA 2.2 mA 2.4 mA 2.6 mA 2.8 mA 3.0 mA 3.2 mA 3.4 mA 3.6 mA 3.8 mA 4.0 mA 4.2 mA 4.4 mA 4.6 mA 4.8 mA 5.0 mA 5.2 mA 5.4 mA 5.6 mA 5.8 mA 6.0 mA 6.2 mA 6.4 mA 6.6 mA 6.8 mA 7.0 mA 7.2 mA 7.4 mA 7.6 mA 7.8 mA 8.0 mA 8.2 mA 8.4 mA 8.6 mA 8.8 mA 9.0 mA 9.2 mA 9.4 mA 9.6 mA 9.8 mA 10.0 mA 10.2 mA 10.4 mA 10.6 mA 10.8 mA 11.0 mA 11.2 mA 11.4 mA 11.6 mA 11.8 mA 12.0 mA 12.2 mA 12.4 mA 12.6 mA 12.8 mA “1000000” : “1000001” : “1000010” : “1000011” : “1000100” : “1000101” : “1000110” : “1000111” : “1001000” : “1001001” : “1001010” : “1001011” : “1001100” : “1001101” : “1001110” : “1001111” : “1010000” : “1010001” : “1010010” : “1010011” : “1010100” : “1010101” : “1010110” : “1010111” : “1011000” : “1011001” : “1011010” : “1011011” : “1011100” : “1011101” : “1011110” : “1011111” : “1100000” : “1100001” : “1100010” : “1100011” : “1100100” : “1100101” : “1100110” : “1100111” : “1101000” : “1101001” : “1101010” : “1101011” : “1101100” : “1101101” : “1101110” : “1101111” : “1110000” : “1110001” : “1110010” : “1110011” : “1110100” : “1110101” : “1110110” : “1110111” : “1111000” : “1111001” : “1111010” : “1111011” : “1111100” : “1111101” : “1111110” : “1111111” : 13.0 mA 13.2 mA 13.4 mA 13.6 mA 13.8 mA 14.0 mA 14.2 mA 14.4 mA 14.6 mA 14.8 mA 15.0 mA 15.2 mA 15.4 mA 15.6 mA 15.8 mA 16.0 mA 16.2 mA 16.4 mA 16.6 mA 16.8 mA 17.0 mA 17.2 mA 17.4 mA 17.6 mA 17.8 mA 18.0 mA 18.2 mA 18.4 mA 18.6 mA 18.8 mA 19.0 mA 19.2 mA 19.4 mA 19.6 mA 19.8 mA 20.0 mA 20.2 mA 20.4 mA 20.6 mA 20.8 mA 21.0 mA 21.2 mA 21.4 mA 21.6 mA 21.8 mA 22.0 mA 22.2 mA 22.4 mA 22.6 mA 22.8 mA 23.0 mA 23.2 mA 23.4 mA 23.6 mA 23.8 mA 24.0 mA 24.2 mA 24.4 mA 24.6 mA 24.8 mA 25.0 mA 25.2 mA 25.4 mA 25.6 mA Bit [6:0] : IU*(6:0) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 26/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note ●Explanation for operate 1. The explanation of Reset There are two kinds of reset, software reset and hardware reset. ●Software reset ・All the registers are initialized by SFTRST="1". ・SFTRST is an automatically returned to "0". (Auto Return 0). ●Hardware reset ・It shifts to hardware reset by changing RESETB pin “H” → “L”. ・The condition of all the registers under hardware reset pin is returned to the initial value, and it stops accepting all address. ・It’s possible to release from a state of hardware reset by changing RESETB pin “L” → “H”. ・RESETB pin has delay circuit. It doesn’t recognize as hardware reset in “L” period under 5μs. ・Even if RESETB=L, at FLASHCNT=H, Flash mode becomes ON by minimum setting. ●Reset Sequence ・When hardware reset was done during software reset, software reset is canceled whenhardware reset is canceled. (Because the initial value of software reset is “0”) 2. The explanation of Thermal shutdown The blocks which thermal shutdown function is effective in the following. Charge pump LED Driver LDO1, LDO2, SBIAS o A thermal shutdown function works in about 190 C. o Detection temperature has a hysteresis, and detection release temperature is about 170 C.(Design reference value) 3. The explanation of Charge Pump for LED driver Charge Pump block is designed for the power supply for LED driver. It has the x1.0/x1.33/x1.5/x2.0 mode. It changes to the most suitable mode automatically by Vf of LED and the battery voltage. It has the mode of x1.33 and it can be higher efficiency than traditional. ●Start Charge Pump circuit operates when any LED turns ON. ●Soft start When the start of the Charge Pump circuit is done, it has the soft start function to prevent a rush current. V BAT T VBATON V IO T VIOON=min 0.1ms RESETB T RSTB=min 0.1ms T RST=min 0ms E N (*1) T SOFT V OUT T VIOOFF=min 1ms T VBATOFF LED Current (*1) An EN signal in the upper figure means the following; “EN is high” = Any LED turns ON But if Ta >TSD, EN Signal doesn’t become effective. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 27/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note ●Charge Pump Mode transition The transition of boost multiple transits automatically by Vf of LED and the battery voltage. STANDBY ALL off Any LED on 1 ○ Ta2.3V(typ) SOFT CP x1.0 mode After “VOUT>1.5V(typ)” detected, 142us(typ) wait X1.0 CP x1.0 mode m ode down=”H” mode up=”H” X1.33 CP x1.33 mode mode down=”H” mode up=”H” X1.5 CP x1.5mode mode down=”H” mode up=”H” X2.0 All LED OFF RESET CP x2.0mode BD6095GUL/BD6095GU changes the four charge pump movement mode automatically to realize low consumption power. < Mode Up > A LED terminal voltage is monitored, and the movement mode is changed to ×1→×1.33, ×1.33→×1.5 and ×1.5→×2 automatically when a LED terminal voltage is lower than 0.2V (typ). At this time, the maximum output voltage of the charge pump is restricted to 5.1V (typ). < Mode Down > The rise in the battery voltage, the off control of LED lighting, “Main Group” LED current value and the data writing to the address 04h,05h,06h (LED Current Setting) is monitored, and the movement mode is changed to ×2→×1.5→×1.33→×1 automatically. This mode down movement lasts until a mode up movement happens. At Flash mode and Torch mode, the mode down doesn't happen. The thresholds of rise in a battery voltage are 2.9V, 3.3V, 3.7V and 4.1V (typ). And, as for the off control of LED lighting, it is shown that MLEDEN, SLEDEN, TORCHEN, FLASHEN and FLASHCNT transited in “1” →“0”. ●Over Voltage protection / Over Current protection Charge Pump circuit output (VOUT) is equipped with the over-voltage protection and the over current protection function. A VOUT over-voltage detection voltage is about 5.5V(typ). (VOUT at the time of rise in a voltage) A detection voltage has a hysteresis, and a detection release voltage is about 5.1V(typ). And, when VOUT output short to ground, input current of the battery terminal is limited by an over current protection function. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 28/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note 4. The explanation of LED Driver ●LED1~LED3 LED1~LED3 are same controlled. These are using for “Main backlight” and we call it “Main Group”. Current setting: IMLED(6:0) ON/OFF: MLEDEN (ON=1, OFF=0) ●LED4~LED5 LED4 and LED5 can be independent controlled. There are attributed to “Main Group” or “Sub Group”. If these are attributed to “Main Group”, these are controlled by same as LED1~LED3. Current setting: ISLED(6:0) ON/OFF: SLEDEN (ON=1, OFF=0) Current setting: IMLED(6:0) ON/OFF: MLEDEN (ON=1, OFF=0) ●The number of LED Lighting (LED1~LED5) The number of lighting for Main/Sub LED can be set up grouping by the register The setting of the number of lighting is as the following. The Main/Sub LED is independently controlled by register MLEDEN, SLEDEN. LED5MD(1) 0 0 1 1 1 1 LED5MD(0) 0 0 0 0 1 1 LED4MD 0 1 0 1 0 1 LED1 Main Main Main Main Main Main LED2 Main Main Main Main Main Main LED3 Main Main Main Main Main Main LED4 Sub Main Sub Main Sub Main LED5 OFF OFF Sub Sub Main Main Main/Sub Setting Example 3/0,3/1 4/0 3/0,3/2 4/0,4/1 4/0,4/1 5/0 The change of the Grouping setting with turning it on is prohibited. The LED terminal that isn’t used must be connected to the ground. ●LEDFL LEDFL is for Flash. It has the two mode, “Torch” and “Flash”. Torch mode current: IFTLED(4:0) Flash mode current: IFFLED(4:0) ON/OFF: TORCHEN, FLASHEN, FLASHCNT (refer to “Power Control” address 02h) Flash mode is started by the rise edge of FLASHEN or FLASHCNT. At FLASHCNT=H, even if RESETB=L, the Flash mode becomes ON, and LED is turned on. (But, the setup of LED current becomes the minimum setting in this case because current setting is reset.) Please set FLASHCNT=L when you don't turn on Flash. TORCHEN FLASHEN or FLASHCNT TORCHEN FLASHEN or FLASHCNT IFFLED (4:0) IFTLED (4:0) IFFLED (4:0) LED current LED current < Torch mode > < Flash mode > < Torch mode > < OFF > < Flash mode > < OFF > www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 29/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note 5. The explanation of ALC (Auto Luminous Control) LCD backlight current adjustment is possible in the basis of the data detected by external ambient light sensor. • Extensive selection of the ambient light sensors (Photo Diode, Photo Transistor, Photo IC(linear/logarithm)) is possible by building adjustment feature of Sensor bias, gain adjustment and offset adjustment. 2 • Ambient data is changed into ambient level by digital data processing, and it can be read through I C I/F. • Register setting can customize a conversion to LED current. (Initial value is pre-set.) • Natural dimming of LED driver is possible with the adjustment of the current transition speed. Usually ON / intermittent Output Voltage Offset Correction PWM enabling WPWMIN Sensor type SBIAS SBIAS Gain Correction Conversion Table Slope Timer Mode Select LED* LCD BackLight Sensor SSENS ADC Data Correction Average Logarithmic Conv. Ambient Level detect Current Conversion Slope process GC1 GC2 Gain Control Main Group LED Driver Sensor Gain Control Ambient Level Main current setting Sensor I/F * Wave form in this explanation just shows operation image, not shows absolute value precisely. LED control (1) Auto Luminous Control ON/OFF ・ ALC block can be independent setting ON/OFF. ・ It can use only to measure the Ambient level. Register : ALCEN Register : MLEDEN Register : MLEDMD ・ Refer to under about the associate ALC mode and Main LED current. ALCEN 0 0 0 1 1 1 MLEDEN 0 1 1 0 1 1 MLEDMD x 0 1 x 0 1 Sensor I/F OFF ( AMB(3:0)=0h ) LED control OFF ON OFF ON ON ALC mode Mode OFF Non ALC mode Main LED current IMLED(6:0) IU0(6:0) (*1) IMLED(6:0) ALC mode (*2) (*1) At this mode, because Sensor I/F is OFF, AMB(3:0)=0h. So, Main LED current is selected IU0(6:0). (*2) At this mode, Main LED current is selected IU0(6:0)~IUF(6:0) It becomes current value corresponding to each brightness. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 30/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Sensor Current (Iout) (2) I/V conversion ・ The bias voltage and external resistance for the I-V conversion (Rs) are adjusted with adaptation of sensor characteristic ・ The bias voltage is selectable by register setup. Register : VSB “0” : SBIAS output voltage 3.0V “1” : SBIAS output voltage 2.6V Ambient SBIAS SSENS voltage VCC SBIAS VSSENS Iout IOUT SSENS Voltage (=Iout x Rs) Sensor IC A/D SSENS Rs is large GND Rs SGND BD6095GUL Rs is small Rs : Sense resistance (A sensor output current is changed into the voltage value.) SBIAS : Bias power supply terminal for the sensor (3.0V / 2.6V by register setting) SSENS : Sense voltage input terminal Ambient SSENS Voltage = Iout x Rs www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 31/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note SSENS Voltage (3) Gain control ・ Sensor gain switching function is built in to extend the dynamic range. ・ It is controlled by register setup. ・ When automatic gain control is off, the gain status can be set up in the manual. Register : GAIN(1:0) ・ GC1 and GC2 are outputted corresponding to each gain status. High Gain mode Low Gain mode Ambient SSENS Voltage Auto Gain mode Ambient Example 1 (Use BH1600FVC) SBIAS Example 2 SBIAS Example 3 SBIAS VCC IOUT SSENS SSENS SSENS Application example 9.5 (*1) BH1600 GC1 GC2 GC1 GC2 SGND 1 GC1 GC2 SGND GC1 GC2 SGND GND Resister values are relative Operating mode GAIN(1:0) setting Gain status GC1 output GC2 output Auto 00 High Low L L Manual High Low 01 10 High Low L L Auto 00 High Low L L Manual High Low 01 10 High Low L L Fixed 11 L : This means that it becomes High with A/D measurement cycle synchronously. (*1) : Set up the relative ratio of the resistance in the difference in the brightness change of the High Gain mode and the Low Gain mode carefully. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 32/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note (4) A/D conversion ・ The detection of ambient data is done periodically for the low power. ・ SBIAS and ADC are turned off except for the ambient measurement. ・ The sensor current may be shut in this function, it can possible to decrease the current consumption. ・ SBIAS pin and SSENS pin are pull-down in internal when there are OFF. ・ SBIAS circuit has the two modes. (Usually ON mode or intermittent mode) Register : ADCYC(1:0) Register : SBIASON ALCEN ADCYC(1:0) 16 times ADC Cycle SBIAS Output Twait= 64ms(typ) ADC Movement (Wait time) W hen SBIASON=1 TAD= 16.4ms(typ) (A/D conversion time) AD start signal GC1, GC2=00 GC1, GC2 TADone= 1.024ms(typ) AMB(3:0) AMB(3:0) 16 times measurement Toprt= 80.4ms(typ) (Operate time) (5) ADC data Gain / offset adjustment ・ To correct the characteristic dispersion of the sensor, Gain and offset adjustment to ADC output data is possible. ・ They are controlled by register setup. Register : SGAIN(3:0) Register : SOFS(3:0) < Gain Adjustment > SSENS Voltage SSENS Voltage SSENS Voltage Ambient Gain adjustment SGAIN(3:0) Ambient Ambient < Offset Adjustment > SSENS Voltage SSENS Voltage SSENS Voltage Offset adjustment SOFS(3:0) Ambient Ambient Ambient www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 33/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note (6) Average filter ・ Average filter is built in to rid noise or flicker. ・ Average is 16 times (7) Ambient level detection ・ Averaged A/D value is converted to Ambient level corresponding to Gain control and sensor type. ・ Ambient level is judged to rank of 16 steps by ambient data. ・ The type of ambient light sensor can be chosen by register. (Linear type sensor / Logarithm type sensor) Register : STYPE “0” : For Linear sensor “1” : For Log sensor ・ Ambient level is output through I2C. Register : AMB(3:0) STYPE GAIN(1:0) Gain Status Ambient level 0h 1h 2h 3h 4h 5h 6h 7h VoS×0/256 VoS×1/256 0 00 Low High 10 Low 01 High 11 - 1 xx - SSENS voltage VoS×0/256 VoS×1/256 VoS×2/256 VoS×3/256 VoS×4/256 VoS×5/256 VoS×7/256 VoS×8/256 VoS×12/256 VoS×13/256 VoS×21/256 VoS×22/256 VoS×37/256 VoS×38/256 VoS×65/256 VoS×66/256 VoS×113/256 VoS×114/256 VoS×199/256 VoS×200/256 VoS×255/256 VoS×0/256 VoS×1/256 VoS×2/256 VoS×3/256 VoS×4/256 VoS×5/256 VoS×7/256 VoS×8/256 VoS×12/256 VoS×13/256 VoS×21/256 VoS×22/256 VoS×37/256 VoS×38/256 VoS×65/256 VoS×66/256 VoS×113/256 VoS×114/256 VoS×199/256 VoS×200/256 VoS×255/256 VoS×0/256 VoS×1/256 VoS×2/256 VoS×3/256 VoS×4/256 VoS×5/256 VoS×6/256 VoS×7/256 VoS×9/256 VoS×10/256 VoS×13/256 VoS×14/256 VoS×19/256 VoS×20/256 VoS×27/256 VoS×28/256 VoS×38/256 VoS×39/256 VoS×53/256 VoS×54/256 VoS×74/256 VoS×75/256 VoS×104/256 VoS×105/256 VoS×144/256 VoS×145/256 VoS×199/256 VoS×200/256 VoS×255/256 VoS×0/256 VoS×17/256 VoS×18/256 VoS×26/256 VoS×27/256 VoS×36/256 VoS×37/256 VoS×47/256 VoS×48/256 VoS×59/256 VoS×60/256 VoS×71/256 VoS×72/256 VoS×83/256 VoS×84/256 VoS×95/256 VoS×96/256 VoS×107/256 VoS×108/256 VoS×119/256 VoS×120/256 VoS×131/256 VoS×132/256 VoS×143/256 VoS×144/256 VoS×155/256 VoS×156/256 VoS×168/256 VoS×169/256 VoS×181/256 VoS×182/256 VoS×255/256 VoS×0/256 VoS×1/256    VoS×2/256 VoS×2/256 VoS×3/256 VoS×3/256 VoS×4/256 VoS×4/256 8h VoS×6/256 VoS×6/256 VoS×7/256 VoS×7/256 9h VoS×11/256 VoS×11/256 VoS×12/256 VoS×12/256 Ah VoS×20/256 VoS×20/256 VoS×21/256 VoS×21/256 Bh VoS×36/256 VoS×36/256 VoS×37/256 VoS×37/256 Ch VoS×64/256 VoS×64/256 VoS×65/256 VoS×65/256 Dh VoS×114/256 VoS×114/256 VoS×115/256 VoS×115/256 Eh VoS×199/256 VoS×199/256 VoS×200/256 VoS×200/256 Fh VoS×255/256 VoS×255/256 This is in case of not adjustments of the gain/offset control. In the Auto Gain control mode, sensor gain changes in gray-colored ambient level. “ ⁄ ” : This means that this zone is not outputted in this mode. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 34/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Main LED Current (8) LED current assignment ・ LED current can be assigned as each of 16 steps of the ambient level. ・ Setting of a user can do by overwriting, though it prepares for the table setup in advance. Register : IU*(6:0) Conversion table can be changed Ambient Level Conversion Table (initial value) Ambient Level 0h 1h 2h 3h 4h 5h 6h 7h Setting data 11h 13h 15h 18h 1Eh 25h 2Fh 3Bh Current value 3.6mA 4.0mA 4.4mA 5.0mA 6.2mA 7.6mA 9.6mA 12.0mA Ambient Level 8h 9h Ah Bh Ch Dh Eh Fh Setting data 48h 56h 5Fh 63h 63h 63h 63h 63h Current value 14.6mA 17.4mA 19.2mA 20.0mA 20.0mA 20.0mA 20.0mA 20.0mA Main LED current (9) Slope process ・ Slope process is given to LED current to dim naturally. ・ LED current changes in the 256Step gradation in sloping. ・ Up(dark→bright),Down(bright→dark) LED current transition speed are set individually. Register : THL(3:0) Register : TLH(3:0) ・ Main LED current changes as follows at the time as the slope. TLH (THL) is setup of time of the current step 2/256. Current Data which is set LED Current TLH(3:0) THL (3:0) Up/Down transition Speed is set individually TLH time 25.6mA =0.1mA 256 THL Zoom Main LED Current TLH(3:0) time www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 35/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note Main LED current (10) LED current reset when mode change ・ When mode is changed (ALC↔Non ALC), it can select the way to sloping. Register : MDCIR “0” : LED current non-reset when mode change “1” : LED current reset when mode change NonALC mode IMLED(6:0) ALC mode NonALC mode IMLED(6:0) IU*(6:0) MDCIR= “0” 0mA time NonALC mode ALC mode NonALC mode IMLED(6:0) Main LED current IMLED(6:0) IU*(6:0) MDCIR= “1” 0mA time (11) Current adjustment ・ When it is permitted by the register setting, PWM drive by the external terminal (WPWMIN) is possible. Register : WPWMEN ・ It is suitable for the intensity correction by external control, because PWM based on Main LED current of register setup or ALC control. WPWMIN (External input) L H WPWMEN 0 0 Back light current ON ON PWM input invalid PWM input valid 1 L Forced OFF 1 H ON Current ON is depending on “MLEDEN”. M LED EN I n te rn a l S o ft-S ta rt T im e D C /D C O u tp u t W P W M IN in p u t W PW M EN L E D C u rre n t It c a n b e in p u tte d W P W M IN b e fo re M L E D E N = 1 . It c a n b e s e t W P W M E N = 1 b e fo re M L E D E N = 1 . P W M m o v e m e n t is e ffe c tiv e a t th e tim e L E D c u rre n t ris e u p . P W M H ig h p u ls e w id th m u s t b e m o re th a n 8 0 µ s . www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 36/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note 6. The explanation of I/O When the RESETB pin is Low, the input buffers (SDA and SCL) are disabling for the Low consumption power. VBAT VIO SCL (SDA) EN RESETB=L, Output “H” LOGIC Level Shift RESETB 7. The explanation of the start of LDO1~LDO2 It must start as follows. V BAT T VBATON T VBATOFF V IO T VIOON=min 0.1ms T VIOOFF=min 1ms R ESETB T R STB=min 0.1ms T RST=min 0ms L DO1EN or LDO2EN T RISE = max 1ms(TBD) L DO1O or LDO2O (LDO output) VBAT ON (Enough rise up) → VIO ON (Enough rise up) → Reset release → LDO ON (Register access acceptable) LDO OFF → Reset → VIO OFF (Enough fall down) → VBAT OFF 8. The explanation of the terminal management of the function that isn’t used Set up the terminal that isn't used as follows. The LED terminal which isn't used : Short to ground Don't do the control concerned with this terminal. T1, T2 : Short to ground T3, T4 : Open www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 37/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●PCB pattern of the Power dissipation measuring board Technical Note 1st layer(component) 2nd layer 3rd layer 4th layer 5th layer 6th layer 7th layer 8th layer(solder) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 38/41 2011.04 - Rev.A BD6095GUL,BD6095GU Technical Note ●Notes for use (1) Absolute Maximum Ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety measures including the use of fuses, etc. (2) Power supply and ground line Design PCB pattern to provide low impedance for the wiring between the power supply and the ground lines. Pay attention to the interference by common impedance of layout pattern when there are plural power supplies and ground lines. Especially, when there are ground pattern for small signal and ground pattern for large current included the external circuits, please separate each ground pattern. Furthermore, for all power supply pins to ICs, mount a capacitor between the power supply and the ground pin. At the same time, in order to use a capacitor, thoroughly check to be sure the characteristics of the capacitor to be used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant. (3) Ground voltage Make setting of the potential of the ground pin so that it will be maintained at the minimum in any operating state. Furthermore, check to be sure no pins are at a potential lower than the ground voltage including an actual electric transient. (4) Short circuit between pins and erroneous mounting In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between pins or between the pin and the power supply or the ground pin, the ICs can break down. (5) Operation in strong electromagnetic field Be noted that using ICs in the strong electromagnetic field can malfunction them. (6) Input pins In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the input pin. Therefore, pay thorough attention not to handle the input pins, such as to apply to the input pins a voltage lower than the ground respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to the input pins when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is applied, apply to the input pins a voltage lower than the power supply voltage or within the guaranteed value of electrical characteristics. (7) External capacitor In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a degradation in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc. (8) Thermal shutdown circuit (TSD) This LSI builds in a thermal shutdown (TSD) circuit. When junction temperatures become detection temperature or higher, the thermal shutdown circuit operates and turns a switch OFF. The thermal shutdown circuit, which is aimed at isolating the LSI from thermal runaway as much as possible, is not aimed at the protection or guarantee of the LSI. Therefore, do not continuously use the LSI with this circuit operating or use the LSI assuming its operation. (9) Thermal design Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in actual states of use. (10) LDO Use each output of LDO by the independence. Don’t use under the condition that each output is short-circuited because it has the possibility that an operation becomes unstable. (11) About the pin for the test, the un-use pin Prevent a problem from being in the pin for the test and the un-use pin under the state of actual use. Please refer to a function manual and an application notebook. And, as for the pin that doesn't specially have an explanation, ask our company person in charge. (12) About the rush current For ICs with more than one power supply, it is possible that rush current may flow instantaneously due to the internal powering sequence and delays. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of wiring. (13) About the function description or application note or more. The function description and the application notebook are the design materials to design a set. So, the contents of the materials aren't always guaranteed. Please design application by having fully examination and evaluation include the external elements. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 39/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Power dissipation (On the ROHM’s standard board) Technical Note 1.6 1500mW 1.4 1.2 Power Dissipation Pd (W) 1.0 0.8 0.6 0.4 0.2 0.0 0 25 50 75 Ta(℃) 100 125 150 Information of the ROHM’s standard board Material : glass-epoxy Size : Refer to after page. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 40/41 2011.04 - Rev.A BD6095GUL,BD6095GU ●Ordering part number Technical Note B D 6 Part No. 6095 0 9 5 G U L - E 2 Part No. Package GUL : VCSP50L3 GU : VCSP85H3 Packaging and forming specification E2: Embossed tape and reel VCSP50L3(BD6095GUL) 1PIN MARK 3.75± 0.1 Tape Quantity 0.1± 0.05 0.55MAX Embossed carrier tape 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold 3.75± 0.1 S Direction of feed ( reel on the left hand and you pull out the tape on the right hand ) 0.08 S 35- φ 0.25± 0.05 0.05 A B (φ0.15)INDEX POST F E D C B A 123456 A B P=0.5× 5 0.625± 0.1 0.625± 0.1 P=0.5× 5 1pin Direction of feed (Unit : mm) Reel ∗ Order quantity needs to be multiple of the minimum quantity. VCSP85H3 (BD6095GU) 3.75± 0.05 1PIN MARK Tape Quantity 0.25± 0.1 1.0MAX Embossed carrier tape 2500pcs E2 The direction is the 1pin of product is at the upper left when you hold 3.75± 0.05 S 0.625± 0.05 Direction of feed ( reel on the left hand and you pull out the tape on the right hand ) 0.06 S 35- φ 0.3± 0.05 0.05 A B (φ0.15)INDEX POST F E D C B A 123456 A B P=0.5 × 5 0.625± 0.05 P=0.5 × 5 1pin Direction of feed (Unit : mm) Reel ∗ Order quantity needs to be multiple of the minimum quantity. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 41/41 2011.04 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A
BD6095GU 价格&库存

很抱歉,暂时无法提供与“BD6095GU”相匹配的价格&库存,您可以联系我们找货

免费人工找货