PRODUCTS
TYPE
FIXED THICK FILM CHIP RESISTORS
MCR01 Series
SPECIFICATION
PRODUCTS: FIXED THICK FILM CHIP RESISTORS
TYPE: MCR01 MRT SERIES
ROHM CO., LTD.RESISTOR DIV.
DESIGN
CHECK
APPROVAL
DATE:
4/NOV/2011
REV. 002E
TSZ22111・04・002
SPECIFICATION No.:MCR01R−1A
PAGE
1/14
PRODUCTS
TYPE
FIXED THICK FILM CHIP RESISTORS
MCR01 Series
PAGE
2/14
< Specifications (Precautions and Prohibitions) >
● Safety Precautions
1) The products are designed and produced for application in ordinary electronic equipment (AV equipment,
OA equipment, telecommunication equipment, home appliances, amusement equipment, etc.).
If the products are to be used in devices requiring extremely high reliability (medical equipment,
transport equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment
including car accessories, safety devices, etc.) and whose malfunction or operational error may endanger
human life and sufficient fail-safe measures, please consult with the ROHM sales staff in advance. If
product malfunctions may result in serious damage, including that to human life, sufficient fail-safe
measures must be taken, including the following:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits in the case of single-circuit failure
2) The products are designed for use in a standard environment and not in any special environments.
Application of the products in a special environment can deteriorate product performance. Accordingly,
verification and confirmation of product performance, prior to use, is recommended if used under the
following conditions:
[a] Use in various types of liquid, including water, oils, chemicals, and organic solvents
[b] Use outdoors where the products are exposed to direct sunlight, or in dusty places
[c] Use in places where the products are exposed to sea winds or corrosive gases, including
Cl2, H2S, NH3, SO2, and NO2
[d] Use in places where the products are exposed to static electricity or electromagnetic waves
[e] Use in proximity to heat-producing components, plastic cords, or other flammable items
[f] Use involving sealing or coating the products with resin or other coating materials
[g] Use involving unclean solder or use of water or water-soluble cleaning agents for cleaning after
soldering
[h] Use of the products in places subject to dew condensation
3) The products are not radiation resistant.
4) Verification and confirmation of performance characteristics of product, after on-board mounting, is
advised.
5)In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse)is
Applied, confirmation of performance characteristics after on-board mounting is strongly recommended.
Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state
Loading condition may negatively affect product performance and reliability.
6) De-rate Power Dissipation(Pd)depending on Ambient temperature(Ta).
7) Confirm that operation temperature is within the specified range described in product specification.
8) Product may be damaged when the impact, such as downfall is given.
9) Failure induced under deviant condition from what defined in the product specification can be not be
Guaranteed.
10)When product safety related problems arises, please immediately inform to ROHM, and consider
technical counter measure.
REV.:
TSZ22111・05・002
002E
SPECIFICATION No.:MCR01R−IA
PRODUCTS
TYPE
FIXED THICK FILM CHIP RESISTORS
MCR01 Series
PAGE
3/14
< Specifications (Precautions and Prohibitions) >
● Precaution for Mounting/Circuit board design
1) When a highly active halogenous (chlorine, bromine, etc.)flux is used, the remainder of flux may
negatively affect product performance and reliability.
2)In principle, the reflow soldering method must be used; if flow soldering method is preferred,please
Consult with the company in advance.
3) Pay attention to the soldering condition in order to avoid problems due to silver absorption into solder.
4) Be careful when pick up the products with tweezers.
There may be a case that the overcoat and /or the body can be chipped.
5) Soldering tip shall not touch the product when install product manually.
● Precautions Regarding Application Examples and External Circuits
1) If change is made to the constant of an external circuit, allow a sufficient margin due to variations of the
characteristics of the products and external components, including transient characteristics, as well as
static characteristics.
2) The application examples, their constants, and other types of information contained herein are applicable
only when the products are used in accordance with standard methods. Therefore, if mass production is
intended, sufficient consideration to external conditions must be made.
● Precaution for Electrostatic
This product is Electrostatic sensitive product, which may be damaged due to Electrostatic discharge.
Please take proper caution during manufacturing and string so that voltage exceeding Product maximum
rating won’t be applied to products. Please take special care under dry condition(e.g. Grounding of human
body /equipment /solder iron, isolation from charged objects, setting of Ionizer, friction prevention and
temperature /humidity control).
● Precaution for strage/Transportation
1)Product performance and soldered connections may deteriorate if the products are stored in the following
places:
[a] Where the products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2,
and NO2
[b] Where the temperature or humidity exceeds those recommended by the Company
Temperature:5―40℃, Humidity 30―80% (Put condition for individual product)
[c] Storage in direct sunshine or condensation
[d] Storage in high Electrostatic
2) Even under ROHM recommended storage condition, solderability of products over 1 year old
(Put condition for each product)may be degraded.
It is strongly recommended storage time period.
・Recommended storage condition:Temperature 5―40℃, Humidity 30―80%(Put condition for
individual product)
3) Store / transport cartons in the correct direction, which is indicated on a carton as a symbol.
Otherwise bent leads may occur due to excessive stress applied when dropping of a carton..
● Precaution for product label
QR code printed on ROHM product label is only for internal use, and please do not use at customer site.
It might contain a internal part number that is inconsistent with an product part number.
● Precaution for disposition
When disposing products please dispose them properly with a industry waste company.
● Precautions for Foreign exchange control regulation
ROHM has not determined whether or not the products are considered “a controlled product or
labor ” as specified in the Foreign Exchange and Foreign Trade Control Law.
Accordingly, if exportation of the products, either separately or integrated in another company’s
products, is intended, or giving the products to persons who are not residents is planed, additional steps
are required, based upon the appropriate regulations.
REV.:
TSZ22111・05・002
002E
SPECIFICATION No.:MCR01R−IA
PRODUCTS
TYPE
FIXED THICK FILM CHIP RESISTORS
MCR01 Series
PAGE
4/14
< Specifications (Precautions and Prohibitions) >
● Prohibitions Regarding Industrial Property
1) These Specifications contain information related to the ROHM industrial property. Any use of them
other than pertaining to the usage of appropriate products is not permitted. Duplication of these
Specifications and its disclosure to a third party without the Company’s permission is prohibited.
2) Information and data on products, including application examples, contained in these specifications are
simply for reference; the Company does not guarantee any industrial property rights, intellectual property
rights, or any other rights of a third party regarding this information or data. Accordingly, the Company
does not bear any responsibility for:
[a] infringement of the intellectual property rights of a third party
[b] any problems incurred by the use of the products listed herein.
3) The Company prohibits the purchaser of its products to exercise or use the intellectual property rights,
industrial property rights, or any other rights that either belong to or are controlled by the Company, other
than the right to use, sell, or dispose of the products.
● Other Matters
1) Please sign these Specifications and return one copy to the Company.
If a copy is not returned within three months after the issued date specified on the front page of these
Specifications, the Company will consider the Specifications accepted.
2) If any matter related to these Specifications needs to be clarified, discussions shall be held promptly
between the two parties concerned to determine the issue.
REV.:
TSZ22111・05・002
002E
SPECIFICATION No.:MCR01R−IA
PRODUCTS
PAGE
5/14
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
1.SCOPE
This specification covers the characteristics of MCR01 series (including jumper type) based
of thick film chip resistors in ROHM Co., Ltd. products.
2.CLASSIFICATION
MCR01
MRT
TYPE
PACKAGING CODE
①
① PACKAGING CODE
PACKAGE
180mm( 7inch)reel, paper tape(2mm pitch)
MRT
② TOLERANCE
J *
TOLERANCE
②
D (±0.5%)
F (±1%)
RESISTANCE VALUE
4digits
D
3digits
J
3.RATING
ITEMS
RATED
POWER
□□□(□) *
RESISTANCE
VALUE(IEC CODE)
* Jumper is 「J 000」
QUANTITY
10,000pcs/reel
J (±5%)
F
CONDITIONS
For resistors operated at the ambient temperature in
excess of 70℃, the load shall be derated in accordance with Fig.1
Fig.1
Rated Power (%)
110
100
90
80
70
60
50
40
30
20
10
0
SPECIFICATIONS
0.063W(1/16W)
at 70℃
155℃
-55℃
70℃
-80 -60 -40 -20
0
20
40
60
80 100 120 140 160 180
Ambient Temperature (℃)
RATED
VOLTAGE
RESISTANCE
Rated voltage is determined from the following.
When rated voltage exceeds the limiting element voltage,
the limiting element voltage shall be the rated voltage.
E = P×R
E: RATED VOLTAGE (V)
P: RATED POWER (W)
R: RESISTANCE
(Ω)
See Table.1
LIMITING ELEMENT VOLTAGE
TEMPERATURE
-55℃∼+155℃
Jumper type
RESISTANCE
MAX.50mΩ
RATED CURRENT
1A
TEMPERATURE
-55℃∼+155℃
RANGE
Table.1
TOLERANCE
D (±0.5%)
F (±1%)
J (±5%)
REV.:
TSZ22111・05・002
50V
019E
RESISTANCE RANGE
(Ω)
10≦R≦1M
(E24)
10≦R<1M
(E24,E96)
1M≦R≦2.2M (E24,E96)
1.0≦R<10
(E24)
10≦R≦10M
(E24)
TEMPERATURE(ppm/℃)
COEFFICIENT
±100
±100
±200
+500/−250
±200
SPECIFICATION No.:MCR01N−IA
PRODUCTS
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
PAGE
6/14
4.CHARACTERISTICS
ITEMS
4.1 RESISTANCE
GUARANTEED VALUE
RESISTOR TYPE
JUMPER TYPE
D: ±0.5%
F: ±1%
J: ±5%
See Table.1
4.2 VARIATION OF
RESISTANCE WITH
TEMPERATURE
4.3 OVERLOAD
4.4 SOLDERABILITY
4.5 RESISTANCE TO
SOLDERING HEAT
4.6 RAPID CHANGE OF
MAX. 50mΩ
±(2.0%+0.1Ω)
MAX. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
±(1.0%+0.05Ω)
MAX. 50mΩ
No remarkable abnormality on the
appearance.
±(1.0%+0.05Ω)
MAX. 50mΩ
±(3.0%+0.1Ω)
MAX. 100mΩ
±(3.0%+0.1Ω)
MAX. 100mΩ
4.9 ENDURANCE
±(3.0%+0.1Ω)
MAX. 100mΩ
4.10 RESISTANCE TO
±(1.0%+0.05Ω)
MAX. 50mΩ
STEADY STATE
4.8 ENDURANCE
AT 70℃
SOLVENT
4.11 BEND STRENGTH
OF THE END
FACE PLATING
JIS C 5201-1 4.5
Measuring method : Measure bottom
termination by 4 proves.
Bottom termination
Prove
JIS C 5201-1 4.8
Measurement:+25/+125℃
Mounting condition: See Fig.3
TEMPERATURE
4.7 DAMP HEAT,
TEST CONDITIONS (JIS C 5201-1)
MAX. 50mΩ
±(1.0%+0.05Ω)
Without mechanical damage such
as breaks.
JIS C 5201-1 4.13
Rated voltage(current)×2.5,2s
Limiting Element Voltage×2:100V
Mounting condition: See Fig.3
JIS C 5201-1 4.17
Rosin・Ethanol(25%WT)
Soldering condition:235±5℃
Duration of immersion:2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition:260±5℃
Duration of immersion:10±1s.
JIS C 5201-1 4.19
Test temp.:-55℃∼+125℃ 300cycle
Mounting condition: See Fig.3
JIS C 5201-1 4.24
40℃,93%RH
Test time:1,000h∼1,048h
Mounting condition: See Fig.3
JIS C 5201-1 4.25.1
Rated voltage(current),70℃
1.5h:ON−0.5h:OFF
Test time:1,000h∼1,048h
Mounting condition: See Fig.3
JIS C 5201 -1 4.25.3
155℃
Test time:1,000h∼1,048h
Mounting condition: See Fig.3
JIS C 5201-1 4.29
23±5℃ , Immersion cleaning, 5±0.5min
Solvent: 2-propanol
JIS C 5201-1 4.33
Mounting condition: See Fig.4
* In the items on characteristics, the expression " ±(1.0% + 0.05Ω)" is used in the column for
standard values.
However, this is because of dramatic increase in the fluctuation ratio that can be take place in the
low resistance value range and is not meant to supplement the measuring accuracy of the
measuring instruments.
Accordingly, there is a need to increase the design tolerance in the low resistance value range.
REV.:
TSZ22111・05・002
019E
SPECIFICATION No.:MCR01N−IA
PRODUCTS
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
5.DIMENSIONS & CONSTRUCTION
Fig.2
(UNIT: mm)
0.20±0.10
①
⑦
⑥
0.35±0.05
②
③
④
⑤
0.50±0.05
0.25+0.05/-0.10
1.00±0.05
№
①
Resistive element
②
Silver thick film electrode
③
Nickel-Chrome electrode
④
Nickel electrode
⑤
Sn electrode
⑥
Alumina substrate
⑦
Over coating (Resin)
REV.:
TSZ22111・05・002
MATERIAL
002E
SPECIFICATION No.:MCR01R−IA
PAGE
7/14
PRODUCTS
PAGE
8/14
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
6.MARKINGS
6.1 Markings on chip resistor
There is no marking on the chip resistor.
6.2
Marking on the packaging container
The following items will be displayed on the smallest unit of the container used for Packaging.
①
②
③
④
⑤
⑥
MCR01 MRT J 102
⑧
F10,000pcs 1138 09001R
FOR ROHM ONLY
ZYXWVUT98765432
012 345 6789 ABC DEFG HIJ0 123 4567 89AB CDE FGHI J
MADE IN CHINA
⑦
①
②
③
Type + Packaging code + Tolerance + Resistance value
Bar code of type code + Resistance value
Special code + Quantity + Lot No.
(There may be label with and without special code.)
④ Bar code of Quantity + Lot No.
⑤ Code for ROHM internal use (This code is not always same as ①)
⑥ Part No.+Order No.
(To be executed on necessity)
⑦ The country of origin.
⑧ QR code (Only for ROHM internal use)
7.APPEARANCE QUALITY
An appearance inspection of the surface should reveal no obvious abnormalities.
① There should be no obvious abnormalities such as bubbles, pin holes or cracks on the overcoat
or outer termination.
② There should be no obvious electrode material or other foreign matter on the overcoat.
③ There should be no obvious electrode material or other foreign matter on back surface of the
substrate and on side surface of the longitudinal axis.
8.MASS
The mass of the chip resistor is 0.8mg±0.5mg.
9.Deciphering the manufacturing date from the Lot No.
An example of the Lot No. is shown below. Read the manufacturing date and take first-in first-out method.
36
××××× ×
11
①
②
③
① Manufacturing year : Last two digits of the western calendar year. (2011)
② Week of manufacture : Shows week 01 to 53 in a year. (36:8/28 to 9/3)
③ Shows line number, serial number or manufacturing plant Code.
Example:
REV.:
TSZ22111・05・002
002E
SPECIFICATION No.:MCR01R−IA
PRODUCTS
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
PAGE
9/14
10.RECOMMENDABLE CONDITION OF SOLDERING
10.1 Reflow Soldering
Reflow soldering with lead free solder.
Condition of soldering
Maximum temperature
Time
: Preheat 150∼180℃ less than 120s.
: Reflow zone 220℃ less than 60s.
: 260±5℃ less than 10s.
: Maximum of twice.
Soldering temperature(℃)
350
260±5℃
max. 10s
300
250
200
150
150∼180℃
max. 120s
100
220℃ over
max. 60s
50
0
0
10.2
1
2
(min)
3
4
Reworking of soldering
Reworking of soldering shall be limited to one time.
① Temperature of soldering tip : 350℃ or less
② Working time : Not longer than 3s.
③ Soldering iron : 20W or less.
11.OTHERS
11.1
In regard to the Export Trade Control Decree.
Resistor That Rohm Co., Ltd.sells is not an object of controlled goods
in Annex 1(Item 1∼15) of Export Trade Control Order.
But it is an object of controlled goods in Annex 1(Item 16) of Export Trade
Control Order. In case of export, please confirm if it applies to "objective" criteria
or an "informed"(by MITT clause) on the basis of "catch-all" controls for
Non-Proliferation of Weapons of Mass Destruction.
11.2
On use of ozone layer destroying substances
No ozone layer destroying substances are used in our resistors.
11.3
On use of fluorocarbons
No specific fluorocarbons or alternative fluorocarbons are used in the manufacture of
our resistors.
11.4
Regarding specific bromine type fire resistant materials
None of the following specific bromine type materials are used in our resistors.
① PBB0s
② PBBs
11.5 Requests prior to changes
In the manufacture and utilization of the chip resistors there are conditions that develop
which require materials or processes to be changed. In such cases, request will be made
prior to clang to obtain approval.
11.6
Manufacturing flow chart and basic design quality
As requested specially, the flow chart for the manufacturing processes of the chip resistor
and the basic quality will be submitted separately.
REV.:
TSZ22111・05・002
002E
SPECIFICATION No.:MCR01R−IA
PRODUCTS
PAGE
10/14
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
Fig.3:TEST BOARD A
(UNIT: mm)
MCR01
ROHM
6.50
2.0
2.70
1.9
0.6
32
8.7
11.5
2.0
2.54
1.32
58.02
NOTE) *1
*2
The shaded area shows the solder resist treatment.
All surface, except terminals used for connectors, receive pre-flux treatment.
Fig.4:TEST BOARD B
0.6
1.6
40
1.5
0.5
100
20
Pressurization
Specimen
Solder
10
R340
3
Tester
NOTE) *1 The shaded area shows the solder resist treatment.
*2 All surface, except terminals used for connectors, receive pre-flux treatment.
*3 During the test, the distance among support points shall be 90mm and the
center of the chip resistor and the center between support points should be
aligned to within ±2mm.
Laminate material: Glass fabric base epoxies.
Compatible with JIS C 6484
Thickness of board:1.6mmt
Copper material: Copper purity is 99.5% or more.
Compatible with JIS C 6484
Copper foil thickness:35µm
REV.:
TSZ22111・05・002
002E
SPECIFICATION No.:MCR01R−IA
PRODUCTS
PAGE
11/14
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
1. SCOPE
This specification covers the tape package requirements for chip resistor MCR01, to be used
on automatic placement systems.
2. PACKAGING CODE
MCR01
TYPE
□□□□
□□□□
□□□
RESISTANCE
VALUE (IEC CODE)
D
F
J
RESISTANCE
TOLERANCE
MRT
PACKAGING
CODE
3. TAPE DIMENSION (UNIT: mm)
P0
φD
P2
0
E
F
W
A0
B0
P1
Top tape
Base paper
(Bottom tape)
Cavlty
Components
T2
W
E
A0
B0
8.0±0.3
3.5±0.05
1.75±0.1
0.7±0.1
1.2±0.1
D0
+0.1
φ1.5
0
P0
P1
P2
T2
4.0±0.1
2.0±0.1
2.0±0.05
MAX.1.1
REV.:
TSZ22111・05・002
F
002E
SPECIFICATION No.:MCR01R−IA
PRODUCTS
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
PAGE
12/14
4. MECHANICAL CHARACTERISTICS
4.1 COVER TAPE PEELING STRENGTH
: 0.07N ≦ PEELING STRENGTH ≦0.50N
Top tape
Base paper
Peel back direction
Feeding direction
Bottom tape
4.2 Base tape should not adhere to top tape when top tape is peeled back, and peel back direction is as follows.
Peel back direction
Base paper
About 170゜
Top tape
Feeding direction
Bottom tape
5. TAPE PACKAGING
5.1 Components are set in tape cavities with the same side (resistive paste upside).
5.2 The accumulated pitch tolerance shall be within ±0.2mm at 10 pitches.
5.3 Tape bent resistance
No damage on the tape and the cavity when tape is bent with the radius of 15mm.
5.4 Components in tape cavity shall not adhere to bottom / cover tape.
5.5 Components shall not be blocked by tape fragments or foreign materials when they are
taken out from cavities.
5.6 The top tape shall not cover up the sprocket holes of tape.
REV.:
TSZ22111・05・002
002E
SPECIFICATION No.:MCR01R−IA
PRODUCTS
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
PAGE
13/14
6. TAPE REEL
6.1 Tape feeding direction shall be shown in the picture drawn below.
Component
0 .4
0 .2
0 .6
0.6
0.4
0.8
0.2
0. 8
Sprocket hole
Feeding direction
Feeding direction
L abel
Label
6.2 Leader tape
Leader tape is given a portion of only cover tape and of blank cavities. (no resistor.)
160mm or more
400mm or more
6.3 Tail tape(trail tape)
Trail tape is given a portion of blank cavities (no resistor).
And the trail tape should not be fixed by adhesive to real and must be the one which can
be pulled out easily from the reel.
40mm or more
REV.:
TSZ22111・05・002
002E
SPECIFICATION No.:MCR01R−IA
PRODUCTS
PAGE
14/14
TYPE
MCR01 Series
FIXED THICK FILM CHIP RESISTORS
0.2
0.4
0.8
0.6
C
0.8
D
0.4
B
0.2
A
0.6
7. REEL DIMENSIONS (UNIT: mm)
L ab e l
A
B
0
+1
φ180
φ60
-1.5
0
C
+1.0
9
0
D
φ13±0.2
MATERIAL
REEL: POLYSTYRENE
PACKING
10,000pcs / Reel
REV.:
TSZ22111・05・002
002E
SPECIFICATION No.:MCR01R−IA