MNR02M0AJ100

MNR02 Resistors Chip resistor networks MNR02 (1005 × 2 size) !Features 1) Extremely small and light Area ratio is 60% smaller than that of chip 1616 (MNR12), while weight ratio has been cut 75%. 2) High-density mounting Can be mounted even more densely than two 1005 chips (MCR01). Also, the cost of mounting has been reduced. 3) Compatible with a wide range of mounting equipment. Squared corners make it excellent for mounting using image recognition devices. 4) Convex electrodes Easy to check the fillet after soldering is finished. 5) ROHM resistors have obtained ISO-9001 certification. Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering it. !Ratings Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70°C. 0.063W (1 / 16W) at 70°C 100 POWER LOAD (%) 80 60 40 20 0 −55 0 70 100 125 155 AMBIENT TEMPERATURE (°C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= P×R P: Rated power (W) R: Nominal resistance (Ω) Nominal resistance Operating temperature Limiting element voltage See Table 1. −55°C to +125°C 25V MNR02 Resistors Table 1 Resistance tolerance J (±5%) Resistance range (Ω) 10≤R≤1M Resistance temperature coefficient (ppm / °C) ±300 (E24) •Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. !Characteristics Items Resistance Variation of resistance with temperature Overload Solderability Resistance to soldering heat Rapid change of temperature Guaranteed value Resistor type J : ±5% See Table.1 ± (2.0%+0.1Ω) A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. ± (1.0%+0.05Ω) No remarkable abnormality on the appearance. JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : −55 / +25 / +125°C JIS C 5201-1 4.13 Rated voltage (current) ×2.5, 2s. Limiting Element Voltage×2 : 50V JIS C 5201-1 4.17 Rosin·Ethanol (25%WT) Soldering condition : 235±5°C Duration of immersion : 2.0±0.5s. JIS C 5201-1 4.18 Soldering condition : 260±5°C Duration of immersion : 10±1s. ± (1.0%+0.05Ω) JIS C 5201-1 4.19 Test temp. : −55°C~+125°C 5cyc ± (3.0%+0.1Ω) JIS C 5201-1 4.24 40°C, 93%RH Test time : 1,000h~1,048h ± (3.0%+0.1Ω) JIS C 5201-1 4.25.1 Rated voltage (current), 70°C 1.5h : ON − 0.5h : OFF Test time : 1,000h~1,048h ± (3.0%+0.1Ω) JIS C 5201-1 4.25.3 125°C Test time : 1,000h~1,048h ± (1.0%+0.05Ω) JIS C 5201-1 4.29 23±5°C, Immersion cleaning, 5±0.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70°C Endurance Resistance to solvent Bend strength of the end face plating Test conditions (JIS C 5201-1) ± (1.0%+0.05Ω) Without mechanical damage such as breaks. JIS C 5201-1 4.33 MNR02 Resistors !External dimensions (Units: mm) 1.0±0.1 6 1.0±0.1 0.2±0.1 0.25±0.1 B A 6 1 5 2 B' +0.1 0.33 −0.05 0.35±0.1 +0.05 0.34 −0.1 0.68 !Equivalent circuit R1 R2 R1 = R2 Material No. 5 Cross section B-B' A' 1 Cross section A-A' 3 4 1 Thick dielectric glaze of ruthenium 2 Thick film of silver for primary electrode 3 Nickel-coated secondary electrode 4 External electrode coated with Sn/Pb or Sn 5 Alumina substrate 6 Overcoating MNR02 Resistors !Packaging Reel Taping P0 0 φD P2 E F W 02 04 06 08 06 D 04 B 02 A 08 B0 A0 P1 Heat crimp cover / Tape Thick paper (Underside paper tape) mount Chip network resistors Square punchout hole T2 C Label (Units: mm) EIAJ ET-7200A compliant W F E A0 B0 8.0±0.3 3.5±0.05 1.75±0.1 1.17±0.1 1.17±0.1 D0 P0 P1 P2 T2 +0.1 φ1.5 0 4.0±0.1 2.0±0.1 2.0±0.05 Max. 0.5 (Units: mm) A φ180 B 0 −3 φ60 +1 0 C 9 D +1.0 0 φ13±0.2 !Product designation Part No. Packaging / Processing specifications Code Part No. Packaging M0 MNR02 Taping Package style Paper tape with reel (10,000) Circuit configuration code A MNR02 Resistance tolerance J ±5% Nominal resistance 3-digit IEC coding system MNR02 Resistors JIS C 5201-1 4.5 SAMPLE SIZE : n=40pcs 20°C 65%RH 5.0 3.0 2.0 1.0 0 −1.0 −2.0 −3.0 −4.0 −5.0 −6.0 10 100 1k 10k 100k 1M 300 2.0 100 0 −100 0 −2.0 −200 −4.0 −300 −400 10 100 1k 10k 100k −6.0 1M 10k 100k Fig.2 Resistance Fig.3 Variation resistance with temperature Fig.4 Overload JIS C 5201-1 4.19 SAMPLE SIZE : n=20pcs −55°C / 125°C 5cyc 2.0 2.0 ∆R/R (%) 0 0 −1.0 −1.0 −2.0 −2.0 −2.0 −4.0 1k 10k 100k −3.0 1M JIS C 5201-1 4.24 SAMPLE SIZE : n=20pcs 40°C 93%RH WITH NO LOAD 1,000h 4.0 1.0 100 1M 6.0 3.0 0 −6.0 10 100 1k 10k 100k 1M 10 100 1k 10k 100k 1M RESISTANCE (Ω) RESISTANCE (Ω) RESISTANCE (Ω) Fig.5 Resistance to soldering heat Fig.6 Rapid change of temperature Fig.7 Damp heat, steady state 6.0 6.0 JIS C 5201-1 4.25.1 SAMPLE SIZE : n=20pcs 70°C 1,000h OVERLOAD : THE RATED VOLTAGE 4.0 JIS C 5201-1 4.25.3 SAMPLE SIZE : n=20pcs 125°C WITH NO LOAD 1,000h 4.0 2.0 ∆R/R (%) 2.0 ∆R/R (%) 1k RESISTANCE (Ω) 1.0 0 0 −2.0 −2.0 −4.0 −4.0 −6.0 100 RESISTANCE (Ω) JIS C 5201-1 4.18 SAMPLE SIZE : n=20pcs SOLDERING CONDITION : 260°C 10s 10 10 RESISTANCE (Ω) 2.0 −3.0 JIS C 5201-1 4.13 SAMPLE SIZE : n=20pcs RATED VOLTAGE×2.5TIMES 2s LIMITING ELEMENT VOLTAGE×2 : 100V 4.0 200 3.0 ∆R/R (%) JIS C 5201-1 4.8 SAMPLE SIZE : n=20pcs 25°C / −55°C 25°C / 125°C ∆R/R (%) DC RESISTANCE (%) 4.0 6.0 400 ∆R/R (%) 6.0 TEMPERATURE COEFFICIENT (ppm / °C) !Electrical characteristics 10 100 1k 10k 100k 1M −6.0 10 100 1k 10k 100k RESISTANCE (Ω) RESISTANCE (Ω) Fig.8 Endurance at 70°C Fig.9 Endurance 1M