SH3004-DC90A

Tentative Printhead SH3004-DC90A Near edge thermal printhead (300 dots / inch) SH3004-DC90A SH-DC90 series was developed with two key structures step-free and near edge for the packaging printer market which requires high speed continuous printing. It is suitable for printers in factory line where high speed 24 hours continuous printing is required. Applications Barcode printers Label printers Packaging printers ATM Ticket printers Scale printers Features 1) ROHM new technology “STEP FREE” structure will provide, high corrosion resistance, better resistance against scratching damage, high efficiency. 2) Head inclination by near-edge structure, applicable to the large-size platen. Resin type thermal-transfer ink-ribbon can be used. 3) High-hardness protect cote type “W-coat” is employed with 150km abrasion life-time. 4) Even without history-control, high-speed printing more than 200mm/s can be achieved at 300dpi with clear print image. With history-control, 300mm/s printing is also possible at 300dpi. External dimensions (Unit : mm) 124±0.5 (7.792) 108.416 DOT No.1 6±0.5 Print Direct ion BU9630 MAX.51 Max.4.5 Max.11 #2 #20 #6 #1 Type of PRINTHEAD #1 CONNECTOR:A #19 CONNECTOR:B 100±0.2 10±0.2 3-M3 Effective Depth 3 2.8±0.2 (43) 31.0±0.5 7.3±0.3 20.45±0.2 (21.2) φ 3 H10 Effective Depth 3 14.208±0.3 40±0.3 80±0.3 φ 3 H10 Length 4 Effective Depth 3 DOT No.1 1/3 Tentative Printhead Equivalent circuit DOT #1280 SH3004-DC90A DOT#1 VH 220µF 35V GND BEO STB2 STB1 LAT LATCH 1280 641 640 1 DI 2 DI 1 CLK VDD 0.1µF 50V GND TM TM DI No. DI 2 DI 1 DOT No. 1280 to 641 640 to 1 STB No. STB2 STB1 DOT No. 1280 to 641 640 to 1 2/3 Tentative Printhead Pin assignments HIROSE No. 1 3 5 7 9 11 13 15 17 19 Circuit VDD GND N.C. LAT GND N.C. VDD STB1 TM SENS2 No. 2 4 6 8 10 12 14 16 18 20 Circuit BEO DI2 CLK GND DI1 GND STB2 TM SENS1 SENS3 JST No. 1 2 3 4 5 6 Circuit VH VH VH GND GND GND SH3004-DC90A Characteristics Parameter Effective printing width Dot pitch Total dot number Average resistance value Applied voltage Applied power Print cycle Maximum number of dots energized simultaneously Maximum clock frequency Maximum roller diameter Running life / pulse life Operating temperature Symbol − − − Rave VH PO SLT − − − − − Typical 108.4 0.0847 1280 850 24 0.57 0.42 1280 10 Unit mm mm dots Ω V W / dot ms dots MHz mm km / pulses φ 50 150 / 108 5 to 45 °C 3/3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1