SJPB-H4V

VRSM = 40 V, IF(AV) = 2.0 A Schottky Diode SJPB-H4 Data Sheet Description Package The SJPB-H4 is a 40 V, 2.0 A Schottky diode with allowing improvements in VF and IR characteristics. These characteristic features contribute to improving power supply efficiency and to enabling high-frequency systems. SJP Features ● ● ● ● ● ● Cathode Mark (2) (1) VRSM ---------------------------------------------------- 40 V IF(AV)---------------------------------------------------- 2.0 A VF (IF = 2.0 A) --------------------------------- 0.49 V typ. Bare Lead Frame: Pb-free (RoHS Compliant) Flammability: Equivalent to UL94V-0 Suitable for High Reliability and Automotive Requirement (1) (2) (1) Cathode (2) Anode Not to scale Applications High speed switching applications as follows: ● DC-DC Converter ● Adapter SJPB-H4-DSE Rev.1.3 SANKEN ELECTRIC CO., LTD. Feb. 17, 2021 https://www.sanken-ele.co.jp/en © SANKEN ELECTRIC CO., LTD. 2016 1 SJPB-H4 Absolute Maximum Ratings Unless otherwise specified, TA = 25 °C. Parameter Symbol Conditions Rating Unit Nonrepetitive Peak Reverse Voltage VRSM 40 V Repetitive Peak Reverse Voltage VRM 40 V Average Forward Current IF(AV) 2.0 A Surge Forward Current IFSM 50 A 12.5 A2s See Figure 2 and Figure 3 Half cycle sine wave, positive side, 10 ms, 1 shot 1 ms ≤ t ≤ 10ms I2t Limiting Value I 2t Junction Temperature TJ − 40 to 150 °C Storage Temperature TSTG − 40 to 150 °C Electrical Characteristics Unless otherwise specified, TA = 25 °C. Parameter Symbol Conditions Min. Typ. Max. Unit Forward Voltage Drop VF IF = 2.0 A — 0.49 0.55 V Reverse Leakage Current Reverse Leakage Current under High Temperature Thermal Resistance(1) IR VR = VRM — — 200 µA VR = VRM, TJ = 150 °C — — 70 mA — — 20 °C/W H∙IR Rth(J-L) Mechanical Characteristics Parameter Package Weight Conditions 1.6 mm TL Device Min. ― Typ. 0.072 Max. ― Unit g TA Copper Area 2 mm 25 mm 2 mm 2 mm Substrate 25 mm Figure 1. (1) Lead Temperature Measurement Conditions Rth (J-L) is thermal resistance between junction and lead. Lead temperature (TL) is measured near the root of pin (see Figure 1). SJPB-H4-DSE Rev.1.3 SANKEN ELECTRIC CO., LTD. Feb. 17, 2021 https://www.sanken-ele.co.jp/en © SANKEN ELECTRIC CO., LTD. 2016 2 SJPB-H4 Derating Curves 2.0 Average Forward Current, IF(AV) (A) Average Forward Current, IF(AV) (A) 2.0 1.6 DC t/T = 1/2 1.2 t/T = 1/3, sine wave t/T = 1/6 0.8 0.4 1.6 DC Sine wave t/T = 1/2 1.2 t/T = 1/3 t/T = 1/6 0.8 0.4 t t T T 0.0 0.0 100 110 120 130 140 150 50 Figure 2. IF(AV) vs. TL (TJ = 150 °C, VR = 0 V) 100 150 Lead Temperature, TL (°C) Lead Temperature, TL (°C) Figure 3. SJPB-H4-DSE Rev.1.3 SANKEN ELECTRIC CO., LTD. Feb. 17, 2021 https://www.sanken-ele.co.jp/en © SANKEN ELECTRIC CO., LTD. 2016 IF(AV) vs. TL (TJ = 150 °C, VR = 40 V) 3 SJPB-H4 Characteristic Curves Maximum Reverse Power Dissipation, PR(MAX) (W) Maximum Forward Power Dissipation, P F(MAX) (W) 2.5 2.0 t T 1.5 t/T = 1/6 t/T = 1/3, sine wave 1.0 0.5 t/T = 1/2 DC t 2.0 T 1−t/T = 5/6 1.5 1−t/T = 2/3 1.0 1−t/T = 1/2 0.5 Sine wave 0.0 0.0 0.0 0.4 0.8 1.2 1.6 0 2.0 20 30 40 Reverse Voltage, VR (V) Average Forward Current, IF(AV) (A) Figure 4. 10 PF(MAX) vs. IF(AV) (TJ = 150 °C) Figure 5. 10 PR(MAX) vs. VR (TJ = 150 °C) 1.E+00 TJ = 150 °C Reverse Leakage Current, IR (A) Forward Current, IF (A) 1.E-01 1 0.1 TJ = 100 °C 0.01 TJ = 25 °C 0.001 1.E-02 TJ = 150 °C 1.E-03 TJ = 100 °C 1.E-04 1.E-05 TJ = 25 °C 1.E-06 1.E-07 0.0 0.2 0.4 0.6 0.8 1.0 0 Typical Characteristics: IF vs. VF 20 30 40 Reverse Voltage, VR (V) Forward Voltage Drop, VF (V) Figure 6. 10 Figure 7. SJPB-H4-DSE Rev.1.3 SANKEN ELECTRIC CO., LTD. Feb. 17, 2021 https://www.sanken-ele.co.jp/en © SANKEN ELECTRIC CO., LTD. 2016 Typical Characteristics: IR vs. VR 4 SJPB-H4 Thermal Resistance (°C/W) 1000 Rth(J-A) 100 Rth(J-L) 10 1 0.1 10m 100m 1 10 100 1000 Pulse Width (s) Figure 8. Typical Transient Thermal Resistance Characteristics SJPB-H4-DSE Rev.1.3 SANKEN ELECTRIC CO., LTD. Feb. 17, 2021 https://www.sanken-ele.co.jp/en © SANKEN ELECTRIC CO., LTD. 2016 5 SJPB-H4 Physical Dimensions ● SJP Package 2.15 0.05 +0.1 -0.2 +0.1 -0.05 2.6±0.2 4.5±0.2 1.3±0.4 2.0min. 1.5±0.2 1.3±0.4 +0.4 5.0 -0.1 NOTES: - Dimensions in millimeters - Bare lead frame: Pb-free (RoHS compliant) Moisture Sensitivity Level 1 (MSL 1) - When soldering the products, it is required to minimize the working time within the following limits: - Flow: 260 °C / 10 s, 1 time Reflow: Preheat: 150 °C to 200 °C / 60 s to 120 s Solder heating: 255 °C / 30s, 3 times (260 °C peak) Soldering Iron: 350 °C / 3.5 s, 1 time ● SJP Land Pattern Example 2.0 2.0 4.0 to 4.2 NOTE: - Dimensions in millimeters SJPB-H4-DSE Rev.1.3 SANKEN ELECTRIC CO., LTD. Feb. 17, 2021 https://www.sanken-ele.co.jp/en © SANKEN ELECTRIC CO., LTD. 2016 6 SJPB-H4 Marking Diagram Cathode Mark Specific Device Code (see Table 1) YMDD Lot Number: Y is the last digit of the year of manufacture (0 to 9) M is the month of the year (1 to 9, O, N, or D) DD is the day of the month (01 to 31) Table 1. Specific Device Code Specific Device Code Part Number BH4 SJPB-H4 SJPB-H4-DSE Rev.1.3 SANKEN ELECTRIC CO., LTD. Feb. 17, 2021 https://www.sanken-ele.co.jp/en © SANKEN ELECTRIC CO., LTD. 2016 7 SJPB-H4 Important Notes ● All data, illustrations, graphs, tables and any other information included in this document (the “Information”) as to Sanken’s products listed herein (the “Sanken Products”) are current as of the date this document is issued. The Information is subject to any change without notice due to improvement of the Sanken Products, etc. Please make sure to confirm with a Sanken sales representative that the contents set forth in this document reflect the latest revisions before use. ● The Sanken Products are intended for use as components of electronic equipment or apparatus (transportation equipment and its control systems, home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Prior to use of the Sanken Products, please put your signature, or affix your name and seal, on the specification documents of the Sanken Products and return them to Sanken. If considering use of the Sanken Products for any applications that require higher reliability (traffic signal control systems or equipment, disaster/crime alarm systems, etc.), you must contact a Sanken sales representative to discuss the suitability of such use and put your signature, or affix your name and seal, on the specification documents of the Sanken Products and return them to Sanken, prior to the use of the Sanken Products. The Sanken Products are not intended for use in any applications that require extremely high reliability such as: aerospace equipment; nuclear power control systems; and medical equipment or systems, whose failure or malfunction may result in death or serious injury to people, i.e., medical devices in Class III or a higher class as defined by relevant laws of Japan (collectively, the “Specific Applications”). Sanken assumes no liability or responsibility whatsoever for any and all damages and losses that may be suffered by you, users or any third party, resulting from the use of the Sanken Products in the Specific Applications or in manner not in compliance with the instructions set forth herein. ● In the event of using the Sanken Products by either (i) combining other products or materials or both therewith or (ii) physically, chemically or otherwise processing or treating or both the same, you must duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. ● Although Sanken is making efforts to enhance the quality and reliability of its products, it is impossible to completely avoid the occurrence of any failure or defect or both in semiconductor products at a certain rate. You must take, at your own responsibility, preventative measures including using a sufficient safety design and confirming safety of any equipment or systems in/for which the Sanken Products are used, upon due consideration of a failure occurrence rate and derating, etc., in order not to cause any human injury or death, fire accident or social harm which may result from any failure or malfunction of the Sanken Products. Please refer to the relevant specification documents and Sanken’s official website in relation to derating. ● No anti-radioactive ray design has been adopted for the Sanken Products. ● The circuit constant, operation examples, circuit examples, pattern layout examples, design examples, recommended examples, all information and evaluation results based thereon, etc., described in this document are presented for the sole purpose of reference of use of the Sanken Products. ● Sanken assumes no responsibility whatsoever for any and all damages and losses that may be suffered by you, users or any third party, or any possible infringement of any and all property rights including intellectual property rights and any other rights of you, users or any third party, resulting from the Information. ● No information in this document can be transcribed or copied or both without Sanken’s prior written consent. ● Regarding the Information, no license, express, implied or otherwise, is granted hereby under any intellectual property rights and any other rights of Sanken. ● Unless otherwise agreed in writing between Sanken and you, Sanken makes no warranty of any kind, whether express or implied, including, without limitation, any warranty (i) as to the quality or performance of the Sanken Products (such as implied warranty of merchantability, and implied warranty of fitness for a particular purpose or special environment), (ii) that any Sanken Product is delivered free of claims of third parties by way of infringement or the like, (iii) that may arise from course of performance, course of dealing or usage of trade, and (iv) as to the Information (including its accuracy, usefulness, and reliability). ● In the event of using the Sanken Products, you must use the same after carefully examining all applicable environmental laws and regulations that regulate the inclusion or use or both of any particular controlled substances, including, but not limited to, the EU RoHS Directive, so as to be in strict compliance with such applicable laws and regulations. ● You must not use the Sanken Products or the Information for the purpose of any military applications or use, including but not limited to the development of weapons of mass destruction. In the event of exporting the Sanken Products or the Information, or providing them for non-residents, you must comply with all applicable export control laws and regulations in each country including the U.S. Export Administration Regulations (EAR) and the Foreign Exchange and Foreign Trade Act of Japan, and follow the procedures required by such applicable laws and regulations. ● Sanken assumes no responsibility for any troubles, which may occur during the transportation of the Sanken Products including the falling thereof, out of Sanken’s distribution network. ● Although Sanken has prepared this document with its due care to pursue the accuracy thereof, Sanken does not warrant that it is error free and Sanken assumes no liability whatsoever for any and all damages and losses which may be suffered by you resulting from any possible errors or omissions in connection with the Information. ● Please refer to our official website in relation to general instructions and directions for using the Sanken Products, and refer to the relevant specification documents in relation to particular precautions when using the Sanken Products. ● All rights and title in and to any specific trademark or tradename belong to Sanken and such original right holder(s). DSGN-AEZ-16003 SJPB-H4-DSE Rev.1.3 SANKEN ELECTRIC CO., LTD. Feb. 17, 2021 https://www.sanken-ele.co.jp/en © SANKEN ELECTRIC CO., LTD. 2016 8