Unipolar 2-Phase Stepper Motor
Driver ICs
SLA7070MS Series
Data Sheet
ns
October, 2018 Rev.1.7
Table of Contents
General Description ................................................................................. 2
2.
Features and Benefits .............................................................................. 2
3.
Part Numbers and Functional Characteristics ...................................... 3
4.
Specifications ............................................................................................ 4
5.
Power Derating Chart .............................................................................. 8
6.
Package Outline Drawing ........................................................................ 9
7.
Functional Block Diagrams and Pin Assignments .............................. 10
8.
Application Example .............................................................................. 12
9.
Truth Tables ............................................................................................ 13
10.
Logic Input Pins ..................................................................................... 14
11.
Logic Input Timing ................................................................................. 15
12.
Step Sequence Diagrams ....................................................................... 16
13.
Individual Circuit Descriptions ............................................................. 22
14.
Functional Descriptions ......................................................................... 24
15.
Application Information ......................................................................... 31
16.
Thermal Design Information ................................................................. 36
R
ec
o
m
m
en
de
d
fo
rN
ew
D
es
ig
1.
17.
Characteristics Data .............................................................................. 38
N
ot
Important Notes ............................................................................................... 39
Sanken Electric Co., Ltd.
https://www.sanken-ele.co.jp/en
1
SLA7070MS Series Datasheet Rev.1.7
1. General Description
This document describes summary of the SLA7070MS series.
2. Features and Benefits
Main power supply voltages, VBB: 46 V (max.), 10 to 44 V normal operating range
Logic supply voltages, VDD: 3.0 to 5.5 V
Maximum output currents, IO(max): 2.0 A, 3.0 A
Clock-in stepping control (built-in sequencer)
Full-, half-, and microstep products are available
Microstepping options are capable of full-, half-, quarter-, eighth-, and
sixteenth-stepping
(6) Built-in “sense resistor” detects motor current
(7) All variants are pin-compatible for enhanced design flexibility
(8) ZIP type 23-pin molded package (SLA package)
(9) Self-excitation PWM current control with fixed OFF-time
For microstepping variants, OFF-time adjusted automatically by step reference
current ratio (3 levels)
(10) Built-in synchronous rectifying circuit reduces power dissipation at PWM-OFF
(11) Synchronous PWM chopping function prevents motor noise in the Hold mode
(12) The Sleep mode to reduce IC input current in stand-by state
(13) Built-in protection circuitry against motor coil opens/shorts and thermal shutdown
protection
(14) The following are the product variants and optional features available:
● Blanking Time
• Full/Half step products:
3.2 µs (standard), 5.2 µs (optional type B)
• Microstep product:
1.7 µs (standard), 3.2 µs (optional type B)
● Input Clock Edge
• Standard type:
POS (positive) edge
• Optional type W:
POS/NEG (positive and negative) edge
en
de
d
fo
rN
ew
D
es
ig
ns
(1)
(2)
(3)
(4)
(5)
N
ot
R
ec
o
m
m
NOTE: The optional types listed above, “type B” and “type W”, are abbreviated and
referred to “B” and “W” as the letters for product branding codes, respectively. These
terms and abbreviations are also used throughout this document. See also Section 6
for more details.
Sanken Electric Co., Ltd.
2
SLA7070MS Series Datasheet Rev.1.7
3. Part Numbers and Functional Characteristics
Table 3-1 provides the product variants available in the SLA7070MS series.
Table 3-1. Part Numbers and Functional Characteristics
Functional Characteristics
Rated Current
(Maximum Setting Value)
Sequencer
Full/Half Step
X
X
Microstep
2.0 A
X
3.0 A
X
X
X
ns
Part Number
SLA7072MS
SLA7073MS
SLA7078MS
ew
D
es
ig
In addition, the following functional options are available in the SLA7070MS series:
● Blanking Time
• Full/Half step products: 3.2 µs (standard), 5.2 µs (optional type B)
• Microstep product:
1.7 µs (standard), 3.2 µs (optional type B)
● Input Clock Edge
• Standard type:
POS (positive) edge
• Optional type W:
POS/NEG (positive and negative) edge
N
ot
R
ec
o
m
m
en
de
d
fo
rN
NOTE: The optional types listed above, “type B” and “type W”, are abbreviated and
referred to “B” and “W” as the letters for product branding codes, respectively. These
terms and abbreviations are also used throughout this document. See also Section 6 for
more details.
Sanken Electric Co., Ltd.
3
SLA7070MS Series Datasheet Rev.1.7
4. Specifications
Table 4-1. Absolute Maximum Ratings
Unless specifically noted, TA = 25 °C
Symbol
Rating
Unit
Remarks
Load (Motor Supply) Voltage
VM
46
V
Main Power Supply Voltage
VBB
46
V
Supply Voltage
VDD
6
V
Power supply to DC
7
V
≤1 μs (5% duty)
2.0
A
Output Current
IO
3.0
A
SLA7072MS
SLA7073MS
SLA7078MS
Logic Input Voltage
VIN
−0.3 to VDD + 0.3
V
REF Input Voltage
VREF
−0.3 to VDD + 0.3
V
Sense Voltage
VRS
±2
V
Allowable Power Dissipation
PD
4.7
W
Junction Temperature
TJ
150
Operating Ambient Temperature
TA
−20 to 85
es
ig
ns
Control
current
value
D
Without heatsink
°C
ew
Characteristic
°C
d
fo
rN
Storage Temperature
Tstg
−30 to 150
°C
NOTE: Output current ratings may be limited by duty cycles, ambient temperatures, and heat
sinking conditions. Do not exceed the maximum output currents and the maximum junction
temperature (TJ) given above, under any conditions of use.
de
Table 4-2. Recommended Operating Conditions
Unless specifically noted, TA = 25 °C
en
Standard Value
Min.
Max.
44
Unit
V
VBB
10
44
V
m
Characteristic
Symbol
Load (Motor Supply) Voltage
VM
m
Main Power Supply Voltage
Remarks
N
ot
R
ec
o
Surge voltage at VDD pin
should be less than ±0.5
Logic Supply Voltage
VDD
3.0
5.5
V
V to avoid malfunctioning
in operation
Measured at Pin 12 (lead
Case Temperature
TC
90
°C
portion), without heatsink
NOTE: As the motor supply voltage, VM, becomes higher, it also approaches the breakdown
voltage of the OUTx pins (100 V min.); and breakdown will be more likely to happen. Even if
one of the OUTx pins breaks down (due to surge noise or other factors), the SLA7070MS
series will recognize it as abnormality (coil open) and will run appropriate protection
functions. Therefore, a thorough evaluation is recommended.
Sanken Electric Co., Ltd.
4
SLA7070MS Series Datasheet Rev.1.7
Table 4-3. Electrical Characteristics 1
Unless specifically noted, TA = 25 °C, VBB = 24 V, and VDD = 5 V
VDSS
100
fclk
250
0.75 ×
VDD
m
IOCP
m
topp
ec
o
R
Overheat Protection
Temperature
FLAG Output Voltage
ot
0.65
Ttsd
VFlagL
VFlagH
Table 4-5, Figure 4-1
Output OFF, Sleep11)
VREF = 0 to1.5 V,
Step reference ratio: 100%
µs
Sleep1, Sleep2
µs
µs
Clock Output ON
Clock Output OFF
V
Motor coils shorted
2.3
3.5
4.6
A
A
A
1.0 A and 1.5 A devices
2.0 A devices
3.0 A devices
2
µs
From PWM-OFF
140
°C
2.0
1.5
en
VOCP
VREF +
0.03
rN
100
µA
µA
V
V
µA
V
VREF
fo
tSE
Overcurrent Detection
Voltage2)
Load Disconnection
Undetected Time
±10
VSENSE
tcon
tcoff
VDD
0.04
2.0
VREF −
0.03
Switching Time
Overcurrent Detection
Current (VOCP / RS)
±1
±1
d
REF Input Current
SENSE Detection
Voltage
Sleep-Enable Recovery
Time
V
de
REF Input Voltage
IIL
IIH
VREF
VREFS
IREF
V
es
ig
VIH
VBB = 44V, ID = 1 mA
kHz Clock duty cycle = 50%
0.25 ×
VDD
Logic Input Voltage
Unit
Conditions
mA Normal mode
µA Sleep1, Sleep2
mA
V
VIL
Logic Input Current
Max.
15
100
5
ns
Min.
D
Logic Power Current
MOSFET Breakdown
Voltage
Maximum Response
Frequency
Symbol
IBB
IBBS
IDD
ew
Characteristic
Main Power Supply
Current
Rating
Typ.
0.7
0.75
1.25
VDD −
1.25
V
Measured at back of device
case (after heat has
saturated)
IFlagL = 1.25 mA
V
IFlagH = −1.25 mA
IFlagL
1.25
mA
−1.25
IFlagH
mA
NOTE: Unless specifically noted, negative current is defined as output current flow from a
specified pin.
1)
In a state of: IBBS, output OFF, and sequencer enabled.
2)
Protection circuit operates when VSENSE ≥ VOCP.
N
FLAG Output Current
Sanken Electric Co., Ltd.
5
SLA7070MS Series Datasheet Rev.1.7
Table 4-4. Electrical Characteristics 2 (Varying with Step Sequence)
(1) Full-/Half-step products: SLA7072MS, SLA7073MS
Unless specifically noted, TA = 25 °C, VBB = 24 V, and VDD = 5 V
Step Reference Current
Ratio
Mode F
Mode 8
Minimum PWM ON-Time
ton(min)
PWM OFF-Time
Rating
Typ.
100
70
Min.
toff
Max.
Unit
Conditions
%
%
VREF ≈ VSENSE = 100%,
VREF = 0 to 1.0 V
Standard type
(w/o branding codes)
Optional type B
(w/ branding codes)
3.2
µs
5.2
µs
12
µs
ns
Symbol
es
ig
Characteristic
(2) Microstep product: SLA7078MS
Unless specifically noted, TA = 25 °C, VBB = 24 V, and VDD = 5 V
ec
o
m
R
MO Output Voltage
N
ot
MO Output Current
Minimum PWM ON-Time
PWM OFF-time
VMOH
IMOL
IMOH
Unit
rN
ew
Max.
fo
m
en
de
Step Reference Current
Ratio
Mode F
Mode E
Mode D
Mode C
Mode B
Mode A
Mode 9
Mode 8
Mode 7
Mode 6
Mode 5
Mode 4
Mode 3
Mode 2
Mode 1
VMOL
Min.
Rating
Typ.
100
98.1
95.7
92.4
88.2
83.1
77.3
70.7
63.4
55.5
47.1
38.2
29
19.5
9.8
D
Symbol
d
Characteristic
1.25
VDD −
1.25
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
V
V
1.25
−1.25
1.7
µs
3.2
µs
12
9
7
µs
µs
µs
Sanken Electric Co., Ltd.
VREF ≈ VSENSE = 100%,
VREF = 0 to 1.0 V
IMOL = 1.25 mA
IMOH = −1.25 mA
mA
mA
ton(min)
toff 1
toff 2
toff 3
Conditions
Standard type
(w/o branding codes)
Optional type B
(w/ branding codes)
Mode 8 to Mode F
Mode 4 to Mode 7
Mode 1 to Mode 3
6
SLA7070MS Series Datasheet Rev.1.7
Table 4-5. Electrical Characteristics 3 (Varying with Output Current Range)
(1) IO = 2.0 A
Unless specifically noted, TA = 25 °C, VBB = 24 V, and VDD = 5 V
RDS(on)
Rating
Typ.
0.25
Max.
0.4
VF
0.95
0.205
Characteristic
Symbol
Output MOSFET ON-Voltage
Output MOSFET Body
Diodes Forward Voltage
Sense Resistor1)
Min.
0.199
Conditions
Ω
ID = 2.0 A
1.2
V
IF = 2.0 A
0.211
Ω
Tolerance: ±3%
Within specified current
REF Input Voltage
VREF
0.04
0.4
V
limit
1)
Includes approximately 5 mΩ circuit resistance in addition to the resistance of the built-in
resistor itself.
es
ig
ns
RS
Unit
(2) IO = 3.0 A
Symbol
Output MOSFET
ON-Resistance
Output MOSFET Body
Diodes Forward Voltage
Sense Resistor1)
Rating
Typ.
Min.
VF
0.95
2.1
V
0.150
0.155
0.160
Ω
0.24
Conditions
ID = 3.0 A
IF = 3.0 A
Tolerance: ±3%
Within specified current
REF Input Voltage
VREF
0.04
0.45
V
limit
1)
Includes approximately 5 mΩ circuit resistance in addition to the resistance of the built-in
resistor itself.
N
ot
R
ec
o
m
m
en
de
d
fo
RS
Unit
Ω
0.18
rN
RDS(on)
Max.
ew
Characteristic
D
Unless specifically noted, TA = 25 °C, VBB = 24 V, and VDD = 5 V
Sanken Electric Co., Ltd.
7
SLA7070MS Series Datasheet Rev.1.7
Figure 4-1. Setting Range of Reference Voltage, VREF
VDD
Sleep1 Set Range
2.0 V
Prohibition Zone
2.0 A
Devices
3.0 A
Devices
Motor Current Set
Range
es
ig
0.45 V
0.4 V
ns
VOCP = 0.7 V
0.04 V
rN
ew
D
NOTE: Extra attentions should be paid to the changeover between the motor current
specification range and the Sleep1 set range. VOCP falls on the “prohibition zone” threshold.
If the changeover takes too long, OCP operation will start when VSENSE > VOCP.
fo
5. Power Derating Chart
N
ot
R
ec
o
m
m
en
de
d
Figure 5-1. Power Derating Chart
Sanken Electric Co., Ltd.
8
SLA7070MS Series Datasheet Rev.1.7
6. Package Outline Drawing
JAPAN
ns
a
c
･
･
･
･
･
en
･
Leadform 2151
23
m
12345
de
d
fo
rN
ew
D
es
ig
b
N
ot
R
ec
o
m
NOTES:
● Dimensions in millimeters
● Pin material: Cu
● Pin plating:
Solder plating (Pb-free)
● Branding codes:
Part number 1: SLA707xMS
• The lowercase letter x represents a number of either of 2, 3, 7, or 8, according to the
combination of rated currents and step sequencers. See also Table 3-1, which lists
the part numbers and corresponding features.
Part number 2: W, B, or WB
• Only optional products have this area labeled with either of the letters listed above.
W, B, and WB stand for optional type W (selectable clock inputs), type B (selectable
blanking times), and type WB (a combined version of types W and B), respectively.
Lot number: YMDD
• Y is the last digit of the year of manufacture
• M is the month of the year (1 to 9, O, N, or D)
• DD is the day of the month (01 to 31)
Sanken Electric Co., Ltd.
9
SLA7070MS Series Datasheet Rev.1.7
7. Functional Block Diagrams and Pin Assignments
9 16 10 15
6
11
20 21 22 23
MIC
Reg.
PreDriver
Sequencer
&
Sleep Circuit
Protection
Protection
Synchro
Control
Comp
-
Rs
PWM
Control
R
ot
OUTA
SENSEA
NC
M1
M2
M3
CLOCK
VBB
GND
REF/SLEEP1
VDD
RESET
CW/CCW
SYNC
FLAG
SENSEB
m
ew
rN
Function
d
en
___________
m
Rs
Phase A output
de
OUTA
ec
o
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Symbol
SENSEB
GND
fo
SYNC
12
19
-
OSC
17
N
+
Comp
PWM
Control
OSC
Pin No.
es
ig
+
5
DAC
TSD
D
DAC
ns
PreDriver
SENSEA
OUTB
8
OUTB
M3
7
OUTB
M2
18
OUTB
M1
13
VBB
FLAG
14
N.C.
REF/SLEEP1
4
RESET
VDD
3
CLOCK
OUTA
2
CW/CCW
OUTA
1
OUTA
OUTA
Figure 7-1. Full-/Half-Step Products: SLA7072MS, SLA7073MS
___
Phase A output
Phase A current sensing
No connection
Input for excitation mode & Sleep2 setting
Step clock input
Main power supply voltage (for motor)
Ground
Input for control current / Sleep1 setting
Power supply to logic
Reset input for internal logic
Forward / reverse input
Synchronous PMW control switch input
Output from protection circuit monitor
Phase B current sensing
___________
___
OUTB
Phase B output
OUTB
Phase B output
Sanken Electric Co., Ltd.
10
SLA7070MS Series Datasheet Rev.1.7
M3
7
8
9 16 10 15
MIC
-
PWM
Control
+
PWM
Control
ew
rN
GND
___
OUTA
Phase A output
en
___________
m
m
SENSEA
MO
M1
M2
M3
CLOCK
VBB
GND
REF/SLEEP1
VDD
RESET
CW/CCW
SYNC
FLAG
19
20
21
22
23
SENSEB
Rs
Function
Phase A output
de
OUTA
18
SENSEB
d
Symbol
ec
o
R
ot
12
fo
SYNC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
-
OSC
17
19
Comp
OSC
Pin No.
es
ig
Synchro
Control
Comp
D
+
N
DAC
TSD
ns
Protection
DAC
Rs
20 21 22 23
PreDriver
Sequencer
&
Sleep Circuit
Protection
5
11
Reg.
PreDriver
SENSEA
OUTB
M2
6
OUTB
M1
18
OUTB
MO
13
OUTB
FLAG
14
VBB
REF/SLEEP1
4
RESET
VDD
3
CLOCK
OUTA
2
CW/CCW
OUTA
1
OUTA
OUTA
Figure 7-2. Microstep Product: SLA7078MS
Phase A current sensing
Output from 2-phase excitation status monitor
Input for excitation mode & Sleep2 setting
Step clock input
Main power supply voltage (for motor)
Ground
Input for control current / Sleep1 setting
Power supply to logic
Reset input for internal logic
Forward / reverse input
Synchronous PMW control switch input
Output from protection circuit monitor for
detecting coil opens/shorts
Phase B current sensing
___________
___
OUTB
Phase B output
OUTB
Phase B output
Sanken Electric Co., Ltd.
11
SLA7070MS Series Datasheet Rev.1.7
8. Application Example
Figure 8-1. Application Example for Microstep Product
VBB = 10 to 44 V
＋
SLEEP
R1
Q1
OUTA
VDD
OUTA
OUTB
VBB
OUTB
es
ig
RESET/SLEEP1
CLOCK
CW/CCW
M1
SLA7070MS Series
M2
M3
SYNC
MO
FLAG
REF/SLEEP
SENSEB
GND
SENSEA
＋
D
CB
C1
CA
ns
VDD = 3.0 to 5.5 V
R3
C2
Power Ground
m
Logic Ground
Single-Point
Ground
m
en
R2
de
d
fo
rN
ew
MicroController
ot
R
ec
o
Constants, for reference use only:
R1 = 10 kΩ
CA = 100 µF / 50 V
R2 = 1 kΩ (VR)
CB = 10 µF / 10 V
R3 = 10 kΩ
C1 = 0.1 µF
C2 = 0.1 µF
N
NOTES:
● Take precautions to avoid noise on the VDD line; noise levels greater than 0.5 V on the VDD
line may cause device malfunction. Noise can be reduced by separating the logic ground
and the power ground on a PCB from the GND pin (Pin 12).
● Unused logic input pins (CW/CCW, M1, M2, M3, RESET, and SYNC) must be pulled up or
down to VDD or ground. If those unused pins are left open, the device may malfunction.
● Unused logic output pins (MO, FLAG) must be kept open.
Sanken Electric Co., Ltd.
12
SLA7070MS Series Datasheet Rev.1.7
9. Truth Tables
(1) Common Input Pins
Table 9-1 shows the truth table for the input pins common to both full-/half-stepping and
microstepping products available in the SLA7070MS series.
Table 9-1.Truth Table for Common Input Pins
Low Level
Normal operation
Forward (CW)
High Level
Logic reset
Reverse (CCW)
—
Commutation (Sleep2 is not included)
ns
Pin Name
RESET
CW/CCW
M1
M2
POS Edge
(Standard)
Sleep1 function
—
Sync PWM control
—
D
SYNC
Normal operation
Non-sync PWM
control
es
ig
M3
REF/SLEEP1
Clock
POS/NEG Edge
(Optional Type W)
N
ot
R
ec
o
m
m
en
de
d
fo
rN
ew
The Reset function is asynchronous. If an input on the RESET pin is high, the internal
logic circuit is reset. At this point, if the REF/SLEEP1 pin stays low, outputs turn on at
the starting point of excitation. Note that a signal on the RESET pin cannot control an
output disable command.
Voltage across the REF/SLEEP1 pin controls PWM currents and the Sleep1 function.
• When VREF ≤ 1.5 V (low level), the REF/SLEEP1 pin functions as the reference
voltage input for normal operation.
• When VREF ≥ 2.0 V (high level), the REF/SLEEP1 pin disables all outputs. This is
the Sleep1 mode that disables the internal linear circuitry and minimizes the main
power supply current, IBB. Although much of the internal circuitry is disabled, the
logic circuit is still active. If an input signal on the CLOCK pin is asserted, the
internal sequencer/translator circuit reacts and sets a step starting point for the
next operation.
The Sleep2 function operates in the same way as the Sleep1 function does, except that
the internal logic circuit enters the Hold mode. Therefore, in the Sleep2 mode, the
internal sequencer/translator circuit is not activated even if a step command signal
occurs on the CLOCK input pin.
The Sync function runs only at “2-phase excitation timing." If this function is used at
other than the 2-phase excitation timing, an overall balance might collapse because PWM
OFF-times and setting currents are different in each of phase A and phase B control
scenario. (If this function is used at a point of 1-phase excitation, it does not react as the
Sync function does. But there is no problem.) The 2-phase excitation timing is a point
where the step reference current ratio of both phases A and B is either of Mode 8 or F.
Sanken Electric Co., Ltd.
13
SLA7070MS Series Datasheet Rev.1.7
(2) Commutation/Sleep2 Function Setting
Table 9-2 provides the logic for the pins (M1, M2, and M3) which set commutation.
rN
ew
D
es
ig
ns
Table 9-2. Truth Table for Commutation/Sleep2 Functions
Function (Pin Name)
M1
M2
M3
Full/Half Step
Microstep
L
L
L
Full step (Mode 8 fixed)
Full step (Mode 8 fixed)
H
L
L
Full step (Mode F fixed)
Full step (Mode F fixed)
L
H
L
Half step (1-2 Phase)
Half step (1-2 Phase)
H
H
L
Half step (Mode F fixed)
Half step (Mode F fixed)
L
L
H
Quarter step (W1-2 Phase)
H
L
H
Eighth step (2W1-2 Phase)
Sleep2 function
L
H
H
Sixteenth step (4W1-2 Phase)
H
H
H
Sleep2 function
NOTE: The Sleep2 function disables outputs and reduces the driver supply current (IBB) in
the same way as the Sleep1 function does. However, unlike the Sleep1 function, the logic
circuitry is put into a “standby” state in the Sleep2 function. Therefore, the
sequencer/translator is not activated even if a step command signal occurs on the CLOCK
input pin. When awaking from the Sleep2 mode, a delay of 100 µs or longer before sending
a clock pulse is recommended.
de
d
fo
(3) Monitor Output Pins
The SLA7070MS series provides two device status monitor outputs:
• MO pin (microstepping product only) – Step sequence
• FLAG pin – Protection feature operation
Table 9-3 shows the logic for the monitor output pins.
Table 9-3. Truth Table for Monitor Output Pins
Low Level
MO
Other than 2-phase excitation timing
m
en
Pin Name
High Level
2-phase excitation timing
R
ec
o
m
FLAG
Normal operation
Protection circuit operation
NOTE: The outputs turn off at the point where the protection circuit starts operating.
To release the protection state, cycle the logic supply voltage, VDD.
10. Logic Input Pins
N
ot
The low pass filter (LPF) incorporated with the logic input pins (CLOCK, RESET,
CW/CCW, M1, M2, M3, and SYNC) improves noise rejection.
The logic inputs are CMOS input compatible; therefore, they are in a high impedance
state. Note that the IC should be used at a fixed input level, either low or high.
If there is a possibility that signals from the microcontroller are in high impedance, add a
pull-up/-down resistor. Since outputs from the logic input pins, which function as output
ON/OFF controllers, may result in abnormal oscillation, leading to MOSFET breakdown as
the worst-case scenario.
Sanken Electric Co., Ltd.
14
SLA7070MS Series Datasheet Rev.1.7
11. Logic Input Timing
(1) Clock Signal
a. A low-to-high transition (rising, or POS edge) or a low-to-high then high-to-low
transition (rising and falling, or POS/NEG edge) on the CLOCK input signal advances
the sequencer/translator. Clock pulse width should be set at 2 μs or longer in both
positive and negative polarities. Therefore, clock response frequency is set to 250 kHz.
b. Clock Edge Timing
With regard to the input logic of the CW/CCW, M1, M2, and M3 pins, a 1 μs delay
should occur both before and after a pulse edge, as setup and hold times (see Figure
11-1). The sequencer logic circuitry might malfunction if the logic polarity is changed
during these setup and hold times.
Figure 11-1. Input Signal Timing
2 µs (min)
5 µs (min)
4 µs (min)
es
ig
Reset
2 µs (min)
Clock
POS/NEG Edge (Optional Type W)
de
d
Clock
CW/CCW
M1
M2
M3
ew
fo
2 µs (min)
5 µs (min)
1 µs (min) 1 µs (min)
rN
1 µs (min) 1 µs (min)
D
2 µs (min)
CW/CCW
M1
M2
M3
Reset
ns
POS Edge (Standard Type)
4 µs (min)
2 µs (min)
2 µs (min)
1 µs (min) 1 µs (min)
1 µs (min) 1 µs (min)
m
en
1 µs (min) 1 µs (min)
m
NOTE: When awaking from the Sleep1 or Sleep2 mode, a delay of 100 µs or longer before
sending a clock pulse is recommended.
N
ot
R
ec
o
(2) Reset Signal
a. Reset Signal Pulse Width
Reset pulse width is equivalent to the hold time of a high level input. It should be 2 µs
or longer, same as the clock pulse width.
b. Reset Release and Clock Input Timing
When the timing of a reset release (falling edge) and a clock edge is simultaneous, the
internal logic might result in an unexpected operation. Therefore, a greater than 5 µs
delay is required between the falling edge of the RESET input signal and the next rising
edge of the CLOCK input signal (see Figure 11-1).
(3) Logic Level Change
Logic level inputs on CW/CCW, M1, M2, and M3 set the translator step direction
(CW/CCW) and step mode (M1, M2, and M3; see also Table 9-2, the commutation truth
table). Changes to those inputs do not take effect until the rising edge of an input signal on
the CLOCK pin. However, depending on the type and state of a motor, there may be errors
in motor operation such as step-out. A thorough evaluation on the changes of sequence
should be carried out.
Sanken Electric Co., Ltd.
15
SLA7070MS Series Datasheet Rev.1.7
12. Step Sequence Diagrams
Figure 12-1. Full Step (2 Phase Excitation)
M1: L, M2: L, M3: L (Mode 8)
RESET
…
CLOCK
0
2
1
B
es
ig
A
0
ew
D
A
ns
CW
70.7
rN
0
70.7
CCW
fo
B
M1: H, M2: L, M3: L (Mode F)
d
RESET
de
CLOCK
1
m
B
…
2
en
0
A
R
0
N
ot
A
ec
o
m
CW
0
10
0
CCW
B
NOTE: All illustrations in this section are based on step sequencing at the POS edge
(standard type). For POS/NEG edge (optional type W) products, both of the rising and
falling edges of a clock input signal activate the step sequencer.
Sanken Electric Co., Ltd.
16
SLA7070MS Series Datasheet Rev.1.7
Figure 12-2. Half Step (1-2 Phase Excitation)
M1: L, M2: H, M3: L (1 Phase: Mode F / 2 Phase: Mode 8)
RESET
…
CLOCK
0
1
2
3
4
B
A
ew
D
0
es
ig
A
ns
CW
70.7
rN
0
10
0
70.7
CCW
fo
B
M1: H, M2: H, M3: L (Mode F)
d
RESET
0
1
…
de
CLOCK
2
4
R
A
0
N
ot
A
ec
o
m
CW
m
en
B
3
0
10
0
CCW
B
NOTE: All illustrations in this section are based on step sequencing at the POS edge
(standard type). For POS/NEG edge (optional type W) products, both of the rising and
falling edges of a clock input signal activate the step sequencer.
Sanken Electric Co., Ltd.
17
SLA7070MS Series Datasheet Rev.1.7
Figure 12-3. Quarter Step (W1-2 Phase Excitation); for microstep product only
M1: L, M2: L, M3: H
ns
RESET
0
1
2
3
4
5
6
7
…
８
ew
D
B
es
ig
CLOCK
0
A
m
en
A
de
d
fo
rN
CW
38.2
70.7
N
92.4
10
0
92.4
ot
R
70.7
CCW
0
ec
om
38.2
B
NOTE: All illustrations in this section are based on step sequencing at the POS edge (standard type). For POS/NEG edge
(optional type W) products, both of the rising and falling edges of a clock input signal activate the step sequencer.
Sanken Electric Co., Ltd.
18
SLA7070MS Series Datasheet Rev.1.7
Figure 12-4. Eighth Step (2W1-2 Phase Excitation); for microstep product only
M1: H, M2: L, M3: H
ns
RESET
0
1
3
2
4
5
6
7
8
9
10
11
12
13
14
…
15
16
ew
D
B
es
ig
CLOCK
0
A
en
A
de
d
fo
rN
CW
m
19.5
70.7
38.2
55.5
70.7
92.4
83.1
10
0
98.1
92.4
98.1
ot
R
83.1
CCW
0
55.5
19.5
ec
om
38.2
B
N
NOTE: All illustrations in this section are based on step sequencing at the POS edge (standard type). For POS/NEG edge
(optional type W) products, both of the rising and falling edges of a clock input signal activate the step sequencer.
Sanken Electric Co., Ltd.
19
SLA7070MS Series Datasheet Rev.1.7
Figure 12-5. Sixteenth Step (4W1-2 Phase Excitation); for microstep product only
M1: L, M2: H, M3: H
ns
RESET
0
1
2
3
5
4
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26
27
…
28
29
30
31
32
ew
D
B
20
es
ig
CLOCK
A
de
d
fo
rN
CW
0
19.5
m
29.0
63.4
70.7
29.0
38.2
47.1
55.5
63.4
70.7
77.3
N
92.4
98.1
95.7
95.7
10
0
98.1
88.2
83.1
83.1
88.2
ot
R
77.3
CCW
0
55.5
9.8
47.1
19.5
ec
om
38.2
92.4
A
en
9.8
B
NOTE: All illustrations in this section are based on step sequencing at the POS edge (standard type). For POS/NEG edge
(optional type W) products, both of the rising and falling edges of a clock input signal activate the step sequencer.
Sanken Electric Co., Ltd.
20
SLA7070MS Series Datasheet Rev.1.7
Excitation Change Sequence
The change of excitation modes is determined by the settings of the excitation pins (M1, M2,
and M3) before and after a step signal. Table 12-1 shows each excitation mode state setting.
Table 12-1. Excitation Mode States
Mode
PWM
Mode
Mode 8
Mode F
A
A
A
A
A
A
A
A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
/A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
F
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
F
F
E
D
C
B
A
9
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
/B
B
B
B
B
B
B
B
8
9
A
B
C
D
E
F
F
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
F
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
X
XX
ec
o
R
ot
N
CW
1)
2)
X
XX
X
2W1-2
Phase
(1/8 Step)
X
X
X
X
X
X
X
X
X
es
ig
X
4W1-2
Phase
(1/16 Step)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ns
PWM
X
X
XX
X
XX
X
ew
X
D
X
rN
X
X
fo
X
X
d
de
X
XX
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
en
m
CCW
Step Sequencing2）
1-2 Phase (Half Step)
W1-2 Phase
(1/4 Step)
Mode 8/F
Mode F
2 Phase (Full Step)
X
m
Direction
Internal Sequence State1)
Phase A
Phase B
X
X
X
X
X
X
X
X
X
X
X
XX
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Each mode is defined accordingly to the SLA7070M series.
XX indicates that sequence state is Mode 8; but step reference current ratio is Mode F.
Mode F has a step reference current ratio of 100%, and a PWM OFF-time of 12 μs.
Sanken Electric Co., Ltd.
21
SLA7070MS Series Datasheet Rev.1.7
13. Individual Circuit Descriptions
(1) Monolithic IC (MIC)
• Sequencer Logic
A single clock strategy is employed for step timing. An input on the CW/CCW pin
determines the direction of motor rotation. Excitation mode is controlled by the
combination of the M1, M2, and M3 input logic levels. See Section 9 for truth tables, and
Section 11 for input timings.
ns
• DAC (D-to-A Converter)
DACs that generate the reference voltage for controlling current. In microstep
sequencing, the current at each step is set by the values of a sense resistor (RS), a
reference voltage (VREF), the output voltage of the DACs, controlled by the output of the
sequencer/translator circuit. For the step reference current ratios, see the electrical
characteristics tables given in Section 4.
ew
D
es
ig
• PWM Control
Circuits that allow self-excitation PWM current controlling with a fixed OFF-time are
used in this series. Each built-in oscillator (OSC) determines an OFF-time and a
blanking time for proper PWM operation. The operation mechanism of the PWM control
circuitry is identical to that of the SLA7070M family. For more detailed functional
descriptions, see Section 14.
m
m
en
de
d
fo
rN
• Synchronous Control
A synchronous chopping circuit that prevents occasional motor noise during a hold
state which normally results from the asynchronous PWM operation of both motor
phases. When the SYNC input pin is set to logic high, the circuit sends a timing signal
that simultaneously turns off the chopping of phases A and B.
This function adopts the same operation mechanism applied to the SLA7070M series.
Therefore, the use of the synchronous control during normal stepping is not
recommended because, it produces less motor torque or may cause motor vibration due
to staircase current.
The use of the synchronous control when the motor is not in operation is only allowed
in 2-phase excitation timing, because the differences in current control values and PWM
OFF-times between phases A and B exist at other excitation timings; otherwise, these
two phases may not be synchronized or may be greatly disrupted in their current control
values.
R
ec
o
• Regulator Circuit
An integrated regulator circuit is used for powering the output MOSFET gate drive
circuit (pre-driver) and other internal linear circuits.
N
ot
• Protection Circuit
Built-in protection circuits against motor coil opens or shorts are provided. This
protection is activated by sensing the voltage across internal sense resistors, RS.
Therefore, an overcurrent condition cannot be detected which results from the OUTx
pins or SENSEx pins, or both, shorting to GND. The protection against motor coil opens
is available only during PWM operation; therefore, it does not work at constant voltage
driving, when the motor is rotating at a high speed.
The operation of the protection circuit disables all outputs. To come out of the
Protection mode, cycle the logic supply, VDD. For more details, see the next section.
• TSD Circuit
A TSD circuit that protects a driver by shifting an output to the Disable mode is
incorporated. When the temperature of the product control IC (MIC) rises and becomes
higher than its threshold, the circuit starts operating. To reset the function, perform the
same steps as described in the Protection Circuit description.
Sanken Electric Co., Ltd.
22
SLA7070MS Series Datasheet Rev.1.7
(2) Output MOSFET Chip
The type of MOSFET chips to be mounted varies according to which of the two different
output current ratings has been selected. For specifications, see Table 4-5.
Rated Current
(A)
Resistance
(Ω Typ.)
2.0
0.25
3.0
0.18
NOTE: Each resistance shown above includes approximately 5 mΩ circuit resistance in
addition to the resistance of the built-in resistor itself.
D
es
ig
ns
(3) Sense Resistor
Sense resistors are incorporated in this series to detect motor current. The resistance of
these varies according to which of the two different output current ratings has been
selected. For specifications, see Table 4-5.
Resistance
(Ω Typ.)
ew
Rated Current
(A)
N
ot
R
ec
o
m
m
en
de
d
fo
rN
2.0
0.205
3.0
0.155
NOTE: Each resistance shown above includes approximately 5 mΩ circuit resistance in
addition to the resistance of the built-in resistor itself.
Sanken Electric Co., Ltd.
23
SLA7070MS Series Datasheet Rev.1.7
14. Functional Descriptions
(1) PWM Current Control
[1] Blanking Time
An actual operating waveform on the SENSEx pin when driving a motor is shown in
Figure 14-1.
ew
D
es
ig
ns
Figure 14-1. Operating Waveform on SENSEx Pin during PWM Chopping
(Circled area of the left panel is shown in expanded scale in the right panel)
ec
o
m
m
en
de
d
fo
rN
Immediately after a PWM turns off, ringing (or spike) noise on the SENSEx pin is
observed for a period of a few microseconds. Ringing noise can be generated by various
causes, such as capacitance between motor coils or inappropriate motor wiring.
Each pair of outputs is controlled by a fixed OFF-time PWM current-control circuit
that limits the load current to a target value, ITRIP. Initially, an output is enabled and
then currents flow through the motor winding and the current sense resistors. When
the voltage across the current sense resistors equals the DAC output voltage, VTRIP,
the current sense comparator resets a PWM latch. This turns off the driver for the
fixed OFF-time, during which the load inductance causes the current to recirculate for
the OFF-time period. Therefore, if the ringing noise on the current sense resistor(s)
equals and surpasses VTRIP, the PWM turns off (i.e., a hunting phenomenon).
To prevent this phenomenon, a blanking time is set to override signals from the
current sense comparator for a certain period immediately after the PWM turns on
(Figure 14-2).
R
Figure 14-2. SENSEx Pin Waveform Pattern during PMW Control
PWM Pulse Width
OFF (Fixed)
N
ot
ON
ITRIP
A
0
A
Blanking Time
Sanken Electric Co., Ltd.
24
SLA7070MS Series Datasheet Rev.1.7
ns
Figure 14-3. Example of SENSEx Pin
Waveform during Hunting
Phenomenon
es
ig
[2] Blanking Time and Hunting Phenomenon
Although current control can be improved by
shortening a blanking time, the degree of
margin to a ringing noise decreases
simultaneously. For this reason, when a motor
is driven by the device, a hunting phenomenon
may occur. Figure 14-3 shows an example of the
waveform pattern when the phenomenon
occurs.
In order to overcome this problem, Sanken
has released a new option, “type B”, which
offers a longer blanking time. Having the
longer blanking time, the optional type B can
improve problems such as torque reduction and
huge motor noise that are occasionally found
during the hunting phenomenon.
rN
ew
D
[3] Blanking Time Difference
Table 14-1 shows characteristic differences between two blanking times, shorter and
longer blanking periods.
This comparison is based on the case where drive conditions, such as a motor, motor
power supply voltage, REF input voltage, and circuit constant were kept the same
while only the indicated parameters were changed.
de
Minimum PWM ON-time
d
fo
Table 14-1. Characteristic Comparison of Difference in Blanking Time
Parameter
Better Performance
Internal blanking time
Short
Long
Small
en
Ringing noise suppression
Small
m
Minimum coil current
Large
Coil current waveform
distortion at a high rotation
(mainly microstep)
ec
o
m
Large
N
ot
R
Brief descriptions for each parameter are as follows:
• Minimum PWM ON-time, tON(min)
This series has a blanking time that is effectively selected and fixed by the
PWM control. Therefore, even if an application attempts to shorten its ON-time
for limiting currents, it would not go below the fixed blanking time. Minimum
PWM ON-time refers to the time when an output is on during this blanking time
period, that is, when an output MOSFET is actually turned on. In other words, a
blanking time determines a minimum ON-time (“Small” in Table 14-1).
• Minimum Coil Current
This refers to the coil current when the PWM control is performed during a
minimum PWM ON-time. In other words, the device with a shorter blanking time
can reduce more coil current.
• Coil Current Waveform Distortion during High-Velocity Revolution
While a microstep drive is active, the ITRIP value changes to a predetermined
value in accordance with a clock input. The ITRIP value (internal reference voltage
splitting ratio) is then set up to be a sine wave. Because the PWM control of motor
coil current is set according to the ITRIP value, (the envelope of) the motor coil
current will also be controlled to be sine wave-like.
Sanken Electric Co., Ltd.
25
SLA7070MS Series Datasheet Rev.1.7
In fact, due to the inductance characteristic of the coil, the device requires some
time to bring the coil current completely to a targeted value (ITRIP).
Roughly, the relationship between the convergence time (tconv), a time until the
coil current settles to its ITRIP value, and the duty cycle (tclk) of an input clock pulse
in any mode is
t CONV < t clk ,
ec
o
m
m
en
de
d
fo
rN
ew
D
es
ig
ns
where the coil current waveform amplitude serves as the limit for ITRIP.
When the current attempts to increase, the full limit of tconv is determined by
power supply voltage and the time constant of the motor coil used. While the
current attempts to decrease, the full limit is determined by the power supply
voltage, the damping time constant of the motor coil used, and the minimum
ON-time.
The duty cycle (tclk) is determined by the frequency of an input clock. It becomes
smaller as the frequency of the input clock increases. When the frequency of the
input clock is raised, because tclk becomes small, it is normal that the coil current
cannot be raised to the ITRIP value within a single clock period. In this situation,
the waveform amplitude of the coil current degenerates from the sine wave,
referred to as “waveform distortion.”
Figure 14-4 illustrates the comparison result of waveform distortions. Devices
with different blanking times were compared under the operating conditions that
power supply voltages, current preset values, motors, and so forth were kept the
same.
As shown in the areas circled (blanking times) in the figure below, the
amplitude envelope of the SENSEx pin waveform in the 1.7 µs case, which is the
same as the current waveform, has become sine wave-like whereas the waveform
in the 3.2 µs blanking time case has degenerated from an ideal sine wave.
The meaning of the team "Large" in Table 14-1 is as follows: if making a
comparison under the same operating conditions, the device with a longer
blanking time will result in less waveform distortion due to a lower clock
frequency. But if the clock frequency is the same, waveform distortion will be
larger due to a shorter blanking time. Even if such distortion is observed, it does
not always mean that the motor characteristics will be negatively affected.
Therefore, thorough evaluations should be carried out to make an informed
decision.
N
ot
R
Figure 14-4. Comparison of SENSEx Pin Waveforms during High-Speed Revolution
Sanken Electric Co., Ltd.
26
SLA7070MS Series Datasheet Rev.1.7
es
ig
ns
[4] PWM OFF-time
PWM OFF-time for the SLA7070MS series is controlled at a fixed time generated by
the corresponding internal oscillator. It also is switched in three levels by step current
reference ratios. (See Table 4-4 for more details.)
In addition, the SLA7070MS series provides a function that decreases power losses
occurring when the PWM turns off. This function dissipates the back EMF stored in the
motor coil at MOSFET turn-on, as well as at PWM turn-on (synchronous rectification
operation).
Figure 14-5 explains differences between two back EMF generation mechanisms.
Whereas the older version of our product series only performs ON/OFF operations using
a MOSFET on the PWM-ON side, the SLA7070MS series can perform ON/OFF
operations using a MOSFET on the PWM-OFF side.
To prevent simultaneous switching of the output MOSFETs at the synchronous
rectification operation, the IC has a dead time of approximately 0.5 μs. During the dead
time, the back EMF flows through the body diodes of the MOSFETs.
Figure 14-5. Difference in Back EMF Generation
Vcc
Ion
Synchronous Rectification Operation
D
Normal Rectification Operation
Ion
rN
SPM
fo
Vg
d
Vg
Rs
en
PWM OFF
PWM ON
m
ec
o
FET Gate Signal
Vg
0
ot
VREF
R
FET Gate Signal
Vg
N
Sense Voltage
0
VRS
Vg
PWM ON
m
PWM ON
SPM
Vg
Vrs
de
Vrs
Ioｆｆ
ew
Ioｆｆ
Vcc
Rs
PWM OFF
Back EMF at Dead Time
PWM ON
Dead Time
FET Gate Signal
Vg
0
FET Gate Signal
Vg
VREF
Sense Voltage
0
VRS
Back EMF flows through the body diode of MOFSET during dead time.
Sanken Electric Co., Ltd.
27
SLA7070MS Series Datasheet Rev.1.7
(2) Protection Functions
The SLA7070MS series includes a motor coil short protection circuit, a motor coil open
protection circuit, and an overheat protection circuit. Detailed explanations of each
protection circuit are provided below.
[1] Motor Coil Short Protection (Load Short) Circuit
This protection circuit, embedded in the SLA7070MS series, begins to operate when
the device detects an increase in the sense resistor voltage, VRS. The threshold voltage
of this protection circuit, VOCP, is set at approximately 0.7 V. Outputs are disabled at a
time when this protection circuit starts, where VRS exceeds VOCP.
Figure 14-6. Motor Coil Short Protection Circuit Operation
VM
es
ig
ns
Coil Short Circuit
SPM
Coil Short
Circuit
D
VOCP
VREF
0
fo
Rs
Output Disable
de
d
VRS
VRS
rN
Vg
ew
Normal Operation
m
en
NOTES:
● Overcurrent that flows without passing the sense resister is undetectable.
● To recover the circuit after the protection operates, VDD must be cycled and started up
again.
N
ot
R
ec
o
m
[2] Motor Coil Open Protection Circuit (Patent acquired)
Driver destruction can occur when one output pin (motor coil) is disconnected in
unipolar drive operation. This is because a MOSFET connected after disconnection
will be in an avalanche breakdown state, where very high energy is added with back
EMF when PWM is off. With the avalanche state, an output cancels the energy stored
in the motor coil where the resisting pressure between the drain and source of the
MOSFET is reached (i.e., the condition in which the breakdown occurred).
Although MOSFETs with a certain amount of an avalanche energy tolerance rating
are used in the SLA7070MS series, the avalanche energy tolerance falls as a
temperature increases.
Because high energy is added repeatedly whenever PWM operation disconnects the
MOSFET, the temperature of the MOSFET rises; and when the applied energy
exceeds the tolerance, the driver will be destroyed. Therefore, a circuit which detects
this avalanche state and protects the driver is added in the SLA7070MS series.
As explained above, when the motor coil is disconnected, accumulated voltage in the
MOSFET causes a reverse current to flow during a PWM OFF-time. For this reason,
VRS that is negative during a PWM OFF-time in normal operation becomes positive
when the motor coil is disconnected. Thus, the disconnected motor is detectable by
sensing that VRS in the PWM OFF-time is positive.
Sanken Electric Co., Ltd.
28
SLA7070MS Series Datasheet Rev.1.7
In order to avoid detection malfunctions, the SLA7070MS series actuates a
dedicated protection function, the motor coil open protection circuit, when the motor
disconnection state is detected three times continuously (see Figure 14-7).
Figure 14-7. Coil Open Protection Operation
PWM Operation
at Normal Device Operation
PWM Operation
at Motor Disconnection
VM
SPM
VM
SPM
Ion
Ioff
Vg
ns
Disconnecton
Vg
Vout
Rs
Vrs
Vrs
Rs
D
Motor
Disconnection
es
ig
Vout
FET Gate Signal
Vg
0
ew
FET Gate Signal
Vg
0
rN
VDSS
fo
2 VM
Vout
VM
0
d
0
Vout
en
VRS
VRS
0
Motor Disconnection Detectable
m
m
0
Breakdown (Avalanche State)
VREF
de
VREF
N
ot
R
ec
o
NOTE: In addition to requiring three breakdown cycles to confirm the open circuit
condition, the SLA7070MS series provides a fixed delay, an overload disconnection
undetected time (topp), before the protection is activated. This is to avoid false
detections, which can be occurred by surge noise after PWM turn-off, causing an
unwanted operation of the function even when the load is not actually disconnected.
The figure below describes alternative topp scenarios. If a total period of breakdown
time exceeds topp, the device shuts down the output. If this is the case, check the motor
and wiring layout to reduce surge noise. Shortening the breakdown time will allow the
protection circuit to function properly. (Variation among device variants and
applications should be taken into consideration.) When there is no actual breakdown,
normal operations will continue. One possible solution is adding a capacitor between
the OUTx and GND pins, which could damp the surge noise sufficiently.
Sanken Electric Co., Ltd.
29
SLA7070MS Series Datasheet Rev.1.7
Surge remains under VDSS
Breakdown ends w/in topp
VDSS
VDSS
VDSS
VOUT
VOUT
VOUT
(B) No effect on operations
(A) Breakdown confirmed
after 3 cycles
Breakdown continues after topp
(C) Generates false detections
es
ig
ns
[3] Overheat Protection Circuit
When a product temperature rises and exceeds Ttsd, this protection circuit starts
operating and sets all outputs to be disabled.
N
ot
R
ec
o
m
m
en
de
d
fo
rN
ew
D
NOTE: This product series has multichip composition (one IC for control, four
MOSFETs, and two chip resistors). Although main heat sources are the MOSFETs and
chip resisters, the location which actually detects temperature is the control IC (MIC).
Separated from these main heat sources, the control IC cannot detect a rapid
temperature change. Accordingly, perform worst-case thermal evaluations, in which
junction temperatures must not exceed a guaranteed value of 150°C, in your
application design phase.
Sanken Electric Co., Ltd.
30
SLA7070MS Series Datasheet Rev.1.7
15. Application Information
(1) Motor Current Ratio Setting
The motor current, IO, for the SLA7070MS series is determined by the values chosen for
the external components, R1 and R2, and the current sense resistors, RS, in the case of the
sample application circuit shown in Figure 8-1. The formula to calculate IO is shown below:
Io =
R2
× VDD / Rs .
R1 + R 2
(1)
VREF
× (Mode Proportion).
RS
(2)
es
ig
I TRIP =
ns
The double-underlined term represents the reference voltage, VREF.
If VREF is set below 0.1 V, the accuracy of IO setting is more likely to be degraded due to
the variation between individual devices and/or the impedance of application trace layout.
The standard voltage for current ITRIP that the SLA7070MS series controls is partially
divided by internal DACs:
Lm
, and
R
R = Rm +.RDS ( on ) + RS .
d
with t C =
de
I O (min )
V M
1
=
− 1 ,
R
−t
exp OFF t
C
fo
rN
ew
D
(2) Lower Limit of Control Current
The SLA7070MS series uses a self-oscillating PWM current-control topology in which
an OFF-time is fixed. As energy stored in a motor coil is eliminated within the fixed PWM
OFF-time, coil current flows intermittently, as shown in Figure 15-1. Thus, average
current decreases as well as motor torque decreases. The point at which current starts
flowing to the coil is considered as the lower limit of the control current, IO(min), where IOUT
is a target current level.
The lower limit of control current differs by application conditions of the motor or other
factors, but it can be calculated from the following formula:
(3)
ec
o
m
m
en
Where:
VM is the motor supply voltage,
RDS(on) is the MOS FET on-resistance,
Rm is the motor winding resistance,
Lm is the motor winding inductance,
tOFF is the PWM OFF-time, and
RS is the current sense resistor.
N
ot
R
Even if the control current value is set at less than its lower limit, there is no setting at
which the IC fails to operate. However, the control current will worsen against its target
current.
Figure 15-1. Model Waveform of Control Current Lower Limit
ITRIP (Large)
A
ITRIP (Small)
0
A
The circled area indicates interval when the coil current generated is 0 A.
Sanken Electric Co., Ltd.
31
SLA7070MS Series Datasheet Rev.1.7
VDS(AV)
rN
ew
From the waveform test result shown in Figure 15-3:
VDS(AV) = 140 V,
ID = 1 A, and
t = 0.5 µs.
D
es
ig
ns
(3) Avalanche Energy
In the unipolar topology of the SLA7070MS series, a surge voltage (ringing noise) that
exceeds the MOSFET capacity to withstand might be applied to the IC. To prevent
damage, the SLA7070MS series is designed with built-in MOSFETs having sufficient
avalanche resistance to withstand this surge voltage.
VM
Therefore, even if surge voltages occur, users will be able to
use the IC without any problems.
SPM
However, in case the motor harness used is too long or the
IC is used above its rated current or voltage, there is a
ID
possibility that an avalanche energy could be applied that
exceeds Sanken design expectations. Thus, users must test
VDS(AV)
the avalanche energy applied to the IC under actual
application conditions.
The following procedure can be used to check the
avalanche energy in an application. Figure 15-2 and Figure
Rs
15-3 show test points and waveform characteristics resultant,
respectively.
Figure 15-2. Test Points
fo
The avalanche energy, EAV, then can be calculated using
the following formula:
EAV ≈ VDS(AV) × 1/2 × ID × t
(4)
= 140 (V) × 1/2 × 1 (A) × 0.5 × 10-6 (μs)
= 0.035 (mJ).
de
d
ID
m
m
en
By comparing the calculated EAV values with the graph
shown in Figure 15-4, the application can be evaluated if it is
safe for the IC by being within the avalanche
energy-tolerated dose range of the MOFSETs.
t
Figure 15-3. Waveform at
Avalanche Breakdown
ec
o
Figure 15-4. Iterated Avalanche Energy Tolerated Level, EAV
20
R
SLA7073MS/78MS
12
SLA7072MS
N
EAV (mJ)
ot
16
[mJ
]
AV
8
E
4
0
0
25
50
75
100
125
150
Product
Temperature,
TC (°C)
Product
Temperature,
TC [°C]
Sanken Electric Co., Ltd.
32
SLA7070MS Series Datasheet Rev.1.7
(4) ON/OFF Sequence of Power Supply (VBB and VDD)
There is no restriction for the ON/OFF sequences of the main power supply, VBB, and
the logic supply, VDD.
(5) Motor Supply Voltage (VM) and Main Power Supply Voltage (VBB)
Because the SLA7070MS series has a structure that separates the contorl IC (MIC)
and the power MOSFETs as shown in Figure 7-1, the motor supply and the main power
supply are electrically separated. Therefore, it is possible to drive the IC with using
different power supplies and different voltages for the motor supply and the main power
supply.
ew
D
es
ig
ns
(6) Internal Logic Circuits
a. Reset for the Internal Sequencer
The sequencer/translator circuit embedded in this product series is initialized by the
built-in power-on reset function, which is activated at a time when the logic supply
(VDD) is applied. Therefore, the output immediately after power-on indicates a status
that the power circuits are in the home state.
When the sequencer/translator must be reset after the motor has been operating, a
signal must be input on the RESET pin. When external reset controlling is not
necessary and the RESET pin is not used, the RESET pin must be pulled to logic low
on an application circuit board.
en
de
d
fo
rN
b. Clock Input
The SLA7070MS series is designed to move one sequence increment at a time when
a clock pulse edge is detected. And there are two different types of sequencer timings:
positive-edge-triggered (standard type, active at a rising edge) and
double-edge-triggered (optional type W, active at a rising edge and a falling edge).
When a clock input signal stops, the present excitation state enters the motor hold
state. At this time, there is no difference to the IC if the clock input signal is at low
level or high level.
N
ot
R
ec
o
m
m
c. Chopping Synchronous Circuit
The SLA7070MS series has a chopping synchronous function to protect from
abnormal noises that may occasionally occur during the motor Hold mode. This
function can be operated by setting the SYNC pin at high level. However, if this
function is used during motor rotation, control current does not stabilize; and that may
result in reduced motor torque and/or increased vibration.
Note that the synchronous circuit should be
Figure 15-5. Clock Signal Shutoff
disabled to control the motor current properly
Detection Circuit
even when it is used in other than the 2-phase
Vcc
excitation state (Modes 8 and F) or the 1-phase
excitation hold state.
CLOCK
SYNC
In
normal
operation,
an
external
74HC14
microcomputer sends an input signal for
switching. However, in applications where any
R
C
input
signals
cannot
be
transmitted
adequately due to a limited number of ports,
the following method can be taken to use the
function.
Figure 15-6. Clock Signal Edge
The schematic diagram in Figure 15-5 shows
Detection Circuit
how the IC is designed so that a signal on the
a
Step
SYNC pin can be determined by an input
Clock
Edge
signal on the CLOCK pin.
Clock
Sanken Electric Co., Ltd.
33
SLA7070MS Series Datasheet Rev.1.7
ns
When the CLOCK pin receives a logic high signal, the internal capacitor, C, is
charged, and the SYNC pin signal is set to logic low. However, if the input signal on
the CLOCK pin cannot rise above a logic low level, the capacitor is discharged by the
internal resistor, R, and the SYNC pin signal is set to logic high, causing the IC to shift
to the synchronous mode. RC time constant in this circuit should be determined by the
minimum clock frequency used.
When using a sequence that keeps an input signal on the CLOCK pin at logic high,
an inverter circuit must be added.
When the CLOCK pin signal is set at an undetermined level or when using a
POS/NEG edge product (optional type W), an edge detection circuit (Figure 15-6) can
be added to prepare a proper clock input signal, allowing correct processing by the
circuit illustrated in Figure 15-5.
de
d
fo
rN
ew
D
es
ig
d. Output Disable Circuits (Sleep1 and Sleep2)
There are two methods to set the IC to a motor free-state (coast, with outputs
disabled). One is to set the REF pin to more than 2 V (Sleep1). And the other is to set
all the excitation mode setting pins (M1, M2, and M3) to high (Sleep2). In either way,
the IC is put into the Sleep mode, which stops the main power supply and reduces
circuit current.
The difference between the two methods is that the Sleep1 keeps the internal
sequencer enabled, whereas the Sleep2 puts the internal sequencer into a hold state.
That is to say, in the Sleep2 mode, the excitation sequence remains in the hold state
even after a signal is input on the CLOCK pin.
When awaking to normal operation mode (motor rotation) from the Disable (Sleep1
or Sleep2) mode, set an appropriate delay time, i.e., a time period from cancellation of
the Disable mode to an initial clock input edge. In doing so, consider not only a rise
time for the IC, but also a rise time for the motor excitation current, which is
important (Figure 15-7).
R
ec
o
m
m
en
Figure 15-7. Timing Delay between Disable Mode
Cancellation and the Next Clock Input
N
ot
NOTE: In applications where POS/NEG edge (optional type W) products are used, the
initial clock signal after the Disable mode cancellation can be a high-to-low transition.
e. REF/SLEEP1 Pin
The REF pin provides access to the following functions:
[1] Reference voltage setting for output current level setting:
Low level (VREF ≤ 0.4 to 0.45 V, depends on rated currents)
[2] Output Enable-Disable control input:
High level (VREF ≥ 2.0 V)
These functions are further described in Section 9, and in the discussion of output
disabling, above. Moreover, the threshold voltage to switch the output enable-disable
signals is set to approximately 1.75 V.
Sanken Electric Co., Ltd.
34
SLA7070MS Series Datasheet Rev.1.7
To control the REF voltage, pay attention to the following points:
Range A – Control current value varies in accordance with VREF, not only within
the range specified in [1], but also within the range from [1] to the threshold
voltage (typically 1.75 V). Therefore, power dissipation in the IC and the sense
resistors must be given extra consideration. In addition, note that OCP operation
may start depending on the reference voltage splitting ratio.
Range B – In this range, the voltage that switches output enable and disable
exists. At enable, the same cautions apply as in Range A. For some cases, there
are possibilities that an output status will become unstable as a result of
iterations between enable and disable states.
es
ig
ns
f. Logic Input Pins (CLOCK, RESET, CW/CCW, M1, M2, M3, and SYNC)
When a logic input pin (CLOCK, RESET, CW/CCW, M1, M2, M3, or SYNC) is not
used, the pin must be tied to VDD or GND. Do not leave any of these pins floating,
because there is possibility of undefined effects on IC performance if they are left open.
ew
D
g. Monitor Output Pins (MO and FLAG)
The MO and FLAG pins are designed as monitor outputs. Moreover, the IC consists
of an inverter output configuration, as shown in Figure 15-8. Therefore, let these pins
open when they are not used.
rN
Figure 15-8. MO/FLAG Pin General Internal Circuit Layout
d
fo
VDD
MO or
FLAG
N
ot
R
ec
o
m
m
en
de
Static Electricity
Protection
Circuit
Sanken Electric Co., Ltd.
35
SLA7070MS Series Datasheet Rev.1.7
16. Thermal Design Information
It is not practical to calculate the power dissipation of the SLA7070MS series accurately,
because that would require factors that are variable during operation, such as time periods
and excitation modes during motor rotation, input frequencies and sequences, and so forth.
Given this situation, it is preferable to perform approximate calculations at worst
conditions. The following is a simplified formula for the calculation of power dissipation
using extracted minimum necessary parameters:
P = I 2 × (R DS(on)＋Rs) × 2 ,
ns
where:
P is the power dissipation in the IC,
I is the operation current (≈ IO),
RDS(on) is the on-resistance of the output MOSFET, and
Rs is the current sense resistance.
ew
D
es
ig
Based on the power dissipation in the IC calculated using the above formula, the expected
increase in operating junction temperature, ΔTJ, of the IC can be estimated using Figure 16-1.
This result should be added to the worst-case ambient temperature when operating, TA(max).
Based on the calculation, there is no problem unless TA(max) + ΔTJ > 150 °C. However, final
confirmation should be made by measuring the IC temperature during operation and then
verifying power dissipation and junction temperature in the corresponding graph in Figure
16-1.
N
ot
R
ec
o
m
m
en
de
d
fo
rN
Figure 16-1. Temperature Increase
When the IC is used with a heatsink mounted, product package thermal resistance, θJ-A, is
a variable used in calculating ΔTJ-A. The value of θJ-A is calculated from the following
formula:
θJ-A ≈ θJ-C + θFIN = (θJ-A – θC-A) + θFIN ,
where θFIN is the thermal resistance of the heatsink. Then, ΔTJ-A can be calculated with using
the value of θJ-A.
Sanken Electric Co., Ltd.
36
SLA7070MS Series Datasheet Rev.1.7
The following procedure should be used to measure product temperature and to estimate
junction temperature in actual operation.
First, measure a temperature rise in the center of backside of mold resin used for the
device (ΔTC-A).
Second, estimate power dissipation (P) and junction temperature (TJ) from the
temperature rise with reference to Figure 16-1, the Temperature Increase graph. At this
point, the device temperature rise (ΔTC-A) and the junction temperature rise (TJ) become
almost equivalent in the following formula:
ΔTJ ≈ ΔTC-A + P × θJ-C .
ns
CAUTION
rN
ew
D
es
ig
The SLA7070MS series is designed as a multichip, consisting of four separate power
elements (MOSFETs), one control IC (MIC), and two sense resistors. Moreover, because the
monolithic IC cannot accurately detect the temperature of the built-in power elements, which
are the primary sources of heat, the SLA7070MS series does not provide a protection function
against overheating. For thermal protection, users must conduct sufficient thermal
evaluations to ensure that the junction temperature of the IC does not exceed a guaranteed
level of 150°C.
N
ot
R
ec
o
m
m
en
de
d
fo
This thermal design information is provided for preliminary design estimations only.
Before operating the IC in an actual application, users must experimentally determine its
actual thermal performance (the case temperature of Pin 12). The maximum recommended
case temperatures (Pin 12) for the IC are:
● With no external heatsink connection: 90°C
● With external heatsink connection:
80°C
Sanken Electric Co., Ltd.
37
SLA7070MS Series Datasheet Rev.1.7
17. Characteristics Data
fo
rN
ew
D
es
ig
ns
(1) Output MOSFET On-Voltage, VDS(on)
N
ot
R
ec
o
m
m
en
de
d
(2) Output MOSFET Body Diodes Forward Voltage, VF
Sanken Electric Co., Ltd.
38
SLA7070MS Series Datasheet Rev.1.7
Important Notes
All data, illustrations, graphs, tables and any other information included in this document (the “Information”)
as to Sanken’s products listed herein (the “Sanken Products”) are current as of the date this document is
issued. The Information is subject to any change without notice due to improvement of the Sanken Products,
etc. Please make sure to confirm with a Sanken sales representative that the contents set forth in this
document reflect the latest revisions before use.
D
es
ig
ns
The Sanken Products are intended for use as components of general purpose electronic equipment or apparatus
(such as home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Prior
to use of the Sanken Products, please put your signature, or affix your name and seal, on the specification
documents of the Sanken Products and return them to Sanken. When considering use of the Sanken Products
for any applications that require higher reliability (such as transportation equipment and its control systems,
traffic signal control systems or equipment, disaster/crime alarm systems, various safety devices, etc.), you
must contact a Sanken sales representative to discuss the suitability of such use and put your signature, or
affix your name and seal, on the specification documents of the Sanken Products and return them to Sanken,
prior to the use of the Sanken Products. The Sanken Products are not intended for use in any applications that
require extremely high reliability such as: aerospace equipment; nuclear power control systems; and medical
equipment or systems, whose failure or malfunction may result in death or serious injury to people, i.e.,
medical devices in Class III or a higher class as defined by relevant laws of Japan (collectively, the “Specific
Applications”). Sanken assumes no liability or responsibility whatsoever for any and all damages and losses
that may be suffered by you, users or any third party, resulting from the use of the Sanken Products in the
Specific Applications or in manner not in compliance with the instructions set forth herein.
ew
In the event of using the Sanken Products by either (i) combining other products or materials or both therewith
or (ii) physically, chemically or otherwise processing or treating or both the same, you must duly consider all
possible risks that may result from all such uses in advance and proceed therewith at your own responsibility.
d
fo
rN
Although Sanken is making efforts to enhance the quality and reliability of its products, it is impossible to
completely avoid the occurrence of any failure or defect or both in semiconductor products at a certain rate. You
must take, at your own responsibility, preventative measures including using a sufficient safety design and
confirming safety of any equipment or systems in/for which the Sanken Products are used, upon due
consideration of a failure occurrence rate and derating, etc., in order not to cause any human injury or death,
fire accident or social harm which may result from any failure or malfunction of the Sanken Products. Please
refer to the relevant specification documents and Sanken’s official website in relation to derating.
de
No anti-radioactive ray design has been adopted for the Sanken Products.
m
en
● The circuit constant, operation examples, circuit examples, pattern layout examples, design examples,
recommended examples, all information and evaluation results based thereon, etc., described in this document
are presented for the sole purpose of reference of use of the Sanken Products.
ec
o
m
Sanken assumes no responsibility whatsoever for any and all damages and losses that may be suffered by you,
users or any third party, or any possible infringement of any and all property rights including intellectual
property rights and any other rights of you, users or any third party, resulting from the Information.
No information in this document can be transcribed or copied or both without Sanken’s prior written consent.
R
Regarding the Information, no license, express, implied or otherwise, is granted hereby under any intellectual
property rights and any other rights of Sanken.
N
ot
Unless otherwise agreed in writing between Sanken and you, Sanken makes no warranty of any kind, whether
express or implied, including, without limitation, any warranty (i) as to the quality or performance of the
Sanken Products (such as implied warranty of merchantability, and implied warranty of fitness for a particular
purpose or special environment), (ii) that any Sanken Product is delivered free of claims of third parties by way
of infringement or the like, (iii) that may arise from course of performance, course of dealing or usage of trade,
and (iv) as to the Information (including its accuracy, usefulness, and reliability).
In the event of using the Sanken Products, you must use the same after carefully examining all applicable
environmental laws and regulations that regulate the inclusion or use or both of any particular controlled
substances, including, but not limited to, the EU RoHS Directive, so as to be in strict compliance with such
applicable laws and regulations.
You must not use the Sanken Products or the Information for the purpose of any military applications or use,
including but not limited to the development of weapons of mass destruction. In the event of exporting the
Sanken Products or the Information, or providing them for non-residents, you must comply with all applicable
export control laws and regulations in each country including the U.S. Export Administration Regulations
(EAR) and the Foreign Exchange and Foreign Trade Act of Japan, and follow the procedures required by such
applicable laws and regulations.
Sanken Electric Co., Ltd.
39
SLA7070MS Series Datasheet Rev.1.7
Sanken assumes no responsibility for any troubles, which may occur during the transportation of the Sanken
Products including the falling thereof, out of Sanken’s distribution network.
Although Sanken has prepared this document with its due care to pursue the accuracy thereof, Sanken does
not warrant that it is error free and Sanken assumes no liability whatsoever for any and all damages and
losses which may be suffered by you resulting from any possible errors or omissions in connection with the
Information.
Please refer to our official website in relation to general instructions and directions for using the Sanken
Products, and refer to the relevant specification documents in relation to particular precautions when using the
Sanken Products.
All rights and title in and to any specific trademark or tradename belong to Sanken and such original right
holder(s).
N
ot
R
ec
o
m
m
en
de
d
fo
rN
ew
D
es
ig
ns
DSGN-CEZ-16003
Sanken Electric Co., Ltd.
40
工商网监
湘ICP备2023018690号
