LB11988

Ordering number :ENN6211 Monolithic Digital IC LB11988 Refrigerator Fan Motor Driver Functions • Three-phase full-wave current linear drive • Built-in current limiter circuit • Built-in saturation prevention circuits in both the upper and lower sides of the output stage. • FG amplifier • Thermal shutdown circuit Package Dimensions unit: mm 3007A-DIP18 [LB11988] 18 10 7.62 6.4 1 24.2 9 1.94 2.54 0.5 1.2 Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Maximum output current Allowable power dissipation Operating temperature Storage temperature Symbol VCCmax VSmax IO max Pdmax Topr Tstg Independent IC Conditions Ratings 24 24 1.3 1.13 –30 to +75 –55 to +150 Unit V V A W °C °C Allowable Operating Ranges at Ta = 25°C Parameter Supply voltage Hall input amplitude Symbol VS VCC VHALL Between Hall inputs Conditions Ratings 5 to 22 7 to 22 ±30 to ±80 Unit V mV 0-P Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN N0999RM (OT) No. 6211-1/6 3.3 3.85max 3.25 SANYO: DIP18 0.25 LB11988 Electrical Characteristics at Ta = 25°C, VCC = 12 V, VS = 12 V Parameter VCC current drain [Output] VOsat1 Output saturation voltage VOsat2 Output leakage current [Hall Amplifier] Input offset voltage Input bias current Common-mode input voltage [FR] Threshold voltage Input bias current [Current Limiter] LIM pin current limit level [Saturation] Saturation prevention circuit lower side voltage setting [FG Amplifier] Upper side output saturation voltage Lower side output saturation voltage Hysteresis TSD operating temperature Vsatu (SH) Vsatd (SH) Vhys T-TSD Design target value* 23 170 11.8 0.3 V V mV °C VOsat (DET) RL = 560 Ω (Y), Rf = 0.5 Ω, The voltage between each lower output and the corresponding Rf. 0.28 V ILIM Rf = 0.5 Ω, With the Hall input logic states fixed (U, V, W = high, high, low) 1 A VFRTH Ib(FR) 4 –5 8 V µA Voff (HALL) Ib (HALL) Vcm (HALL) VIN, WIN 3 –6 1 +6 3 VCC – 3 mV µA V IOleak IO = 500 mA, Rf = 0.5 Ω, Sink + Source (Saturation prevention function included) IO = 1.0 A, Rf = 0 Ω, Sink + Source (Saturation prevention function included) 2.1 2.6 2.6 3.5 1.0 V V mA Symbol ICC RL = 560 Ω (Y) Conditions Ratings min typ 15 max 24 Unit mA Note *: Items shown to be design target values in the conditions column are not measured. Pin Assignment WOUT 1 NC 2 FGOUT 3 FR 4 GND 5 FC 6 U I N+ 7 U I N– 8 V I N+ 9 18 VOUT 17 UOUT 16 NC 15 RF LB11988 14 VS 13 VCC 12 W I N– 11 W I N+ 10 V I N– Top view No. 6211-2/6 LB11988 Truth Table and Control Functions Source → sink 1 V →W W →V U →W W →U U →V V →U W →V V →W W →U U →W V →U U →V Hall input U H V H W L Note: The "H" state for FR is defined as a voltage of 8 V or higher, and the "L" state for FR is defined as a voltage of 4 V or lower. (When VCC = 12 V.) Note: For the Hall inputs, the input high state is defined to be the state where the (+) input is higher than the corresponding (–) input by 0.01 V or higher, and the input low state is defined to be the state where the (+) input is lower than the corresponding (–) input by 0.01 V or higher. FR H L H L H L H L H L H L 2 H L L 3 H L H 4 L L H 5 L H H 6 L H L Note: Since this drive technique is a 180° current application scheme, the phases other than the sink and the source phases will not turn off. Pin Functions Pin No. 5 3 4 6 7, 8 9, 10 11, 12 13 14 Pin GND FG-OUT FR FC UIN+, UIN– VIN+, VIN– WIN+, WIN– VCC VS Function Ground for circuits other than the output transistors. Note that the Rf pin will be at the lowest potential of the output transistors. This is the FG amplifier output pin. Internally, it is a resistive load. Forward/reverse switching pin Corrects the frequency characteristics of the saturation prevention circuit loop and current limiter circuit. U-phase Hall input. Logic high refers to the state where IN+ > IN–. V-phase Hall input. Logic high refers to the state where IN+ > IN–. W-phase Hall input. Logic high refers to the state where IN+ > IN–. Power supply provided to all IC internal circuits other than the output block. This voltage must be stabilized so that ripple and noise do not enter the IC. Output block power supply Used for output current detection. The current limiter circuit operates using the resistor (Rf) connected between this pin and ground. Note that the lower side saturation prevention circuit operates according to the voltage that appears on this pin. Since the over-saturation level is set by this voltage, the response of the lower side saturation prevention circuit may be degraded in the large current region if the value of Rf is made extremely small. U-phase Hall output V-phase Hall output W-phase Hall output (These pins include internal spark killer diodes.) 15 Rf 17 18 1 UOUT VOUT WOUT No. 6211-3/6 LB11988 Equivalent Circuit Diagrams Pin Equivalent circuit diagrams UIN (+) UIN (–) VIN (+) VIN (–) WIN (+) WIN (–) Input (+) Input (–) 200 Ω 100 µA 200 Ω Vs Output Vcc 150 µA Lower side oversaturation prevention circuit input block. UOUT VOUT WOUT RF VS 30 kΩ RF Vcc 200 Ω 200 µA FR FR 200 Ω 1/2 Vcc Vcc FC 10 kΩ FC Vcc Vcc 10 kΩ FGOUT 5 kΩ 300 Ω FGOUT No. 6211-4/6 0.1 µ FC VS Block Diagram VCC UIN + UIN – UOUT VOUT WOUT VIN + VIN – WIN+ Logarithmic conversion and differential distribution Hall input synthesis block (linear matrix) Synthesized output logarithmic compression block WIN– 0.1µ × 3 RF LB11988 FR Differential distribution Forward /reverse switing 0.5 Upper side saturation prevention control Drive distribution circuit and lower side saturation prevention control Feedback amplifier VCC LIMREF Current limiter Schmitt amplifier 5K Bandgap 1.2 V TSD VCC Reference voltage UIN + UIN – FG amplifier 13.6 k GND 30 k FGOUT Unit (capacitance: F, resistance: Ω) No. 6211-5/6 LB11988 Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification” for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of November, 1999. Specifications and information herein are subject to change without notice. PS No.6211-6/6