T8LNP

Specifications: Stepping Motor T8LNP-60 1. Product Description Model Number: Stepping Motor T8LNP-60 2. Motor Characteristics Electrical Characteristics [Measurement Conditions] • Motor Configuration: Horizontal output shaft • Temperature/Humidity: Measurement is, in principle, performed at -10°C~50°C and relative humidity of 30~90%. If in doubt, use the JIS standard temperature state (25 ±2°C, 65 ±5%). • Standard Drive Circuit: LB1836M (Sanyo) Item Model No. of Phases Number of Magnetic Poles Applied to Rotor Basic Step Angle Rated Voltage Excitation Method Coil Resistance Insulation Class Insulation Resistance Insulation Resistance Coil Inductance 2 10 18° (2-phase excitation) DC 6.5V 2-phase bipolar excitation 60 ±10%Ω/Phase E Class 115°C At least 10MΩ at 50V DC 1 min. at 50V AC 10.5mH/Phase ±20% (Reference value) (at 1KHz, 1Vrms) Temperature 25 ±2°C Humidity 65 ±5% 25°C conversion value Content PM-Type Stepping Motor Notes Sanyo Seimitsu, Inc.1771 Nakamaruko, Maruko City, Nagano Prefecture, Japan Page 1 of 6 Specifications: Stepping Motor T8LNP-60 Mechanical Characteristics Item Motor Configuration Usage Temperature/ Humidity Range Storage Temperature Range Rotation Direction Rotor Inertia Pull-in Torque –20~70°C –40~80°C (Standard temperature of 20°C and relative humidity of 65% assumed) The sequence is shown in the diagram on Page 6. Calculated Value V = 6.5V, (between the motor terminals) 2-phase excitation, 500pps V = 6.5V, (between the motor terminals) 2-phase excitation Temperature 25 ±2°C Humidity 65 ±5% V=5.0V, (between the motor terminals) 2-phase excitation V = 6.5V, (between the motor terminals) 2-phase excitation, 500pps Measurement Environment In an environment with a noise level of less than 25dB, set a noise measurement device equipped with a photocoupler to the A range, then perform measurement with a distance of 1cm from the photocoupler to the motor. V = 6.5V, (between the motor terminals) Content Omnidirectional Notes Bi-directional Rotation 0.0093g•cm2 At least 0.30mN• m Maximum Response Frequency Maximum Actuation Frequency Holding Torque At least 2000pps (zero load) At least 1000pps (zero load) At least 0.6mN• m Detent Torque Noise Less than 0.20mN• m Less than 55dB Vibration Less than 6.0m/s2 Sanyo Seimitsu, Inc.1771 Nakamaruko, Maruko City, Nagano Prefecture, Japan Page 2 of 6 Specifications: Stepping Motor T8LNP-60 Reliability Item Operation Lifetime Testing Conditions/Test Environment –10°C: 20,000 rotations Room Temperature: 30, 000 rotations 50°C: 20,000 rotations Operation. Filter: Open Closed Assumes a 2 second rest. Performed for 100 cycles with a pattern of -20°C: 30 minutes, 60°C: 30 minutes. Temperature: -40 ±2°C Storage Time: 72 Hours Determination Standard Perform testing at the conditions at left with the actual device provided by Sanyo Electric. After testing, the determination standards table should be satisfied. Thermal Shock Test Should satisfy the determinations standards table after 1 hour or more placement at normal temperature and humidity. Should satisfy the determinations standards table after 1 hour or more placement at normal temperature and humidity. Should satisfy the determinations standards table after 1 hour or more placement at normal temperature and humidity. Should satisfy the determinations standards table after 1 hour or more placement at normal temperature and humidity. Should satisfy the determination standards table under the environment at left. Should satisfy the determination standards table. Low Temperature Testing High Temperature Testing Temperature: 80 ±2°C Storage Time: 168 Hours Humidity Resistance Testing Temperature: 40 ±2°C Humidity: 90% Placement Time: 168 Hours Temperature: -20 ±2°C 70°C: ±2 Placement Time: 5 Hours　 Fix the motor to a jig No. of Vibrations: 1000 c.p.m. Amplitude: 3mm Direction: X, Y, Z Time: 30 minutes in each direction With the motor in its smallest packaging state, perform a free-fall drop once onto each of the six sides onto a concrete bed from a height of 80cm. On the input terminals: Temperature: 350 °C Time: 3 sec. Solder Type: 60% eutectic solder On the input terminals: Temperature: 230 ±5°C Time: 5 sec. Solder Type: 60% eutectic solder Temperature Characteristics Testing Vibration Testing Drop Testing Should satisfy the determination standards table. Solder Temperature Resistance Should satisfy the determination standards table. Solderability Should be covered by at least 95% new solder. The flux should be a rosin-type. Sanyo Seimitsu, Inc.1771 Nakamaruko, Maruko City, Nagano Prefecture, Japan Page 3 of 6 Specifications: Stepping Motor T8LNP-60 Reliability Determination Standards Table Reliability Item 6 Temperature Characteristics Testing 7 Vibration Testing 3 Low Temperature Testing 4 High Temperature Testing Characteristic Item 9 Solder Temperature Resistance ○ NA NA ○ ○ 1 Operation Lifetime Testing 2 Thermal Shock Test 5 Humidity Resistance Testing 8 Drop Testing ○ NA NA ○ ○ 7 1 3 8 Number Pull-in Torque Coil Resistance Insulation Resistance Maximum Response Frequency Maximum Actuation Frequency ○ ○ ○ ○ ○ NA NA ○ ○ NA NA ○ ○ NA NA ○ ○ NA NA ○ ○ NA NA ○ ○ NA NA ○ 9 ○ ○ ○ ○ ○ ○ ○ *Note: Reliability Determination Standard 1 is determined by 5 samplings where AC = 0 and RE = 1. Sanyo Seimitsu, Inc.1771 Nakamaruko, Maruko City, Nagano Prefecture, Japan Page 4 of 6 Specifications: Stepping Motor T8LNP-60 　 Sanyo Seimitsu, Inc.1771 Nakamaruko, Maruko City, Nagano Prefecture, Japan Page 5 of 6 Specifications: Stepping Motor T8LNP-60 Note 1 History Date Based on FM014300 7/4/02 Note Changes Name Ichikawa (Shin) Lot No. Print Position 0.4921 11/11/02 Ichikawa (Shin) The Lot No. is displayed on the inner side of the motor terminal The Lot No. Print Color: Black 132 0.4921 Lot Number Print Position 2.1654 Note) φ 3.14 – 0.3 – 0.9843 Head Gap Gear Constant Rotation Displacement +0.02 -0.05 Sequence FPC Terminal Step No. No. 1 2 3 4 #2 @ + + #3 A + + #4 B + + #5 C + + CW viewed from the output shaft during the above excitation 0.7874 Support Plate 0.7874 1.193 – 0.0 -0.06 (Gear Height) 2.6575 1.5748 1. There should be no burrs on the gear teeth 2. The gear teeth should be 32 3. The gear pull-out strength should be at least 30.0N 4. The maximum shaft thrust play is 0.3 5. There should be no obvious deformation or damage in the motor appearance. 6. The FPC should be attached at delivery and the dimensions should be according to the FPC drawing (T06062200) The Lot No. Print Method Day of Manufacture (1=1 ~ 9=9, 10 = A, 11=B~31=V) Month Display (Jan.~Sep.=1~9, Oct.~Dec. = X, Y, Z) Shows the last number of the western calendar year (2002=2, 2003=3) 1.0827 User Code Print Position Gear Specifications Gear Tooth Type Gear Shape Module Pressure Angle No. of Teeth Standard Pitch Diameter Outer Diameter Involute Parallel 0.25 20° 10 φ2.5 Gear Specifications Displacement Count Tooth Bottom Diameter Tooth Bottom R Material Precision 2 Tool φ2.025 (0.375m) C3604BD JIS Class 5 0.3937 0.7874 User Code Print Position The user code is positioned 90° from the motor terminal Print Color: Black User Code Display Method: B06 (Brush Diameter) 1.5748 (Motor Outer Diameter) User Code Device Name Dimetric Scale General Tolerance General Specs. Projection Designed Engineering Ichikawa Shin Drafted Engineering Ichikawa Shin Checked Engineering Matsubara Reviewed Engineering Kinoshita Approved Engineering Yagi Parts Code Sanyo Seimitsu, Inc.1771 Nakamaruko, Maruko City, Nagano Prefecture, Japan Page 6 of 6 (Brush Height)