2SD1685G

Ordering number:EN2042A NPN Epitaxial Planar Silicon Transistor 2SD1685 20V/5A Switching Applications Applications Package Dimensions · Strobe, voltage regulators, relay drivers, lamp drivers. unit:mm 2042B [2SD1685] 8.0 3.3 1.5 7.5 3.0 11.0 4.0 1.0 1.0 · Low saturation voltage. · Large current capacity. · Fast switching time. · No insulator required when mounting because the leadframe of the chip is covered with plastic. 1.4 Features 15.5 3.0 1.6 0.8 0.8 0.7 0.75 1 2 1.7 2.4 Specifications 1 : Emitter 2 : Collector 3 : Base SANYO : TO-126ML 3 4.8 Absolute Maximum Ratings at Ta = 25˚C Parameter Symbol Conditions Ratings Unit Collector-to-Base Voltage VCBO 60 V Collector-to-Emitter Voltage VCEO 20 V Emitter-to-Base Voltage VEBO IC 6 V 5 A Collector Current (Pulse) ICP 8 A Collector Dissipation PC 1.5 W Junction Temperature Tj Storage Temperature Tstg Collector Current 10 W 150 ˚C –55 to +150 ˚C Tc=25˚C Electrical Characteristics at Ta = 25˚C Parameter Symbol Collector Cutoff Current ICBO IEBO Emitter Cutoff Current hFE1 DC Current Gain hFE2 Gain-Bandwidth Product fT Cob Output Capacitance * The 2SD1685 is classified by 500mA hFE as follows : 120 E 200 160 F 320 280 G Conditions VCB=50V, IE=0 VEB=5V, IC=0 VCE=2V, IC=500mA VCE=2V, IC=3A VCE=10V, IC=50mA VCB=10V, f=1MHz Ratings min typ max 120* Unit 100 nA 100 nA 560* 95 120 MHz 45 pF Continued on next page. 560 Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquaters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 21599TH (KT)/4277TA, TS No.2042–1/4 2SD1685 Continued from preceding page. Parameter Collector-to-Emitter Saturation Voltage Base-to-Emitter Saturation Voltage Collector-to-Base Breakdown Voltage Collector-to-Emitter Breakdown Voltage Emitter-to-Base Breakdown Voltage Symbol VCE(sat) VBE(sat) Turn-ON Time Storage Time Ratings min typ IC=3A, IB=60mA 220 IC=3A, IB=60mA V(BR)CBO IC=10µA, IE=0 V(BR)CEO IC=1mA, RBE=∞ V(BR)EBO ton Fall Time Conditions IE=10µA, IC=0 max Unit 500 mV 1.5 V 60 V 20 V 6 V See specified Test Circuit. 30 ns tstg See specified Test Circuit. 300 ns tf See specified Test Circuit. 40 ns Switching Time Test Circuit No.2042–2/4 2SD1685 No.2042–3/4 2SD1685 Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of February, 1999. Specifications and information herein are subject to change without notice. PS No.2042–4/4