RGL34A

RGL34A THRU RGL34M Elektronische Bauelemente VOLTAGE 50V ~ 1000V 0.5AMP Surface Mount Fast Recovery Rectifiers RoHS Compliant Product A suffix of "-C" specifies halogen-free FEATURES * Low forward voltage drop * Low leakage current * High reliability DO-213AA/ SOD-80/ Mini Melf .145(3.683) .022(.559) .131(3.327) .016(.406) SOLDERABLE ENDS MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Metallurgically bonded construction * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 0.015 grams .066(1.67) .060(1.52) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature unless otherwise specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length at Ta=55 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 0.5A Maximum DC Reverse Current Ta=25 C at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: RGL34A RGL34B RGL34D RGL34G RGL34J RGL34K RGL34M UNITS 50 35 50 100 70 100 200 140 200 400 280 400 0.5 30 1.3 5.0 100 600 420 600 800 560 800 1000 700 1000 V V V A A V µA µA 250 500 nS pF C 150 15 -65 +175 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. http://www.SeCoSGmbH.com Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 1 of 2 RGL34A THRU RGL34M Elektronische Bauelemente VOLTAGE 50V ~ 1000V 0.5AMP Surface Mount Fast Recovery Rectifiers RATING AND CHARACTERISTIC CURVES (RGL34A THRU RGL34M) FIG.1-TYPICAL FORWARD CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE 50 INSTANTANEOUS FORWARD CURRENT,(A) 0.6 0.5 0.4 0.3 0.2 0.1 0 0 20 40 60 80 100 120 140 160 180 200 Single Phase Half Wave 60Hz Resistive Or Inductive Load 10 3.0 1.0 Tj=25 C Pulse Width 300us 1% Duty Cycle AMBIENT TEMPERATURE ( C) FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWAARD SURGE CURRENT,(A) 50 0.1 .01 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLT AGE,(V) 40 FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE 30 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method 20 10 (+) 25Vdc (approx.) () 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) D.U.T. () PULSE GENERATOR (NOTE 2) (+) 0 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. FIG.5-TYPICAL JUNCTION CAPACITANCE trr +0.5A | | | | | | | | JUNCTION CAPACITANCE,(pF) 15 10 0 -0.25A 5 -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm 0 .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V) http://www.SeCoSGmbH.com Any changing of specification will not be informed individual 01-Jun-2002 Rev. A Page 2 of 2