BCY39A_02

BCY39A MECHANICAL DATA Dimensions in mm (inches) 8.51 (0.34) 9.40 (0.37) SMALL SIGNAL PNP TRANSISTORS 7.75 (0.305) 8.51 (0.335) 6.10 (0.240) 6.60 (0.260) 12.70 (0.500) min. 0.89 max. (0.035) 0.41 (0.016) 0.53 (0.021) dia. APPLICATIONS 5.08 (0.200) typ. Small signal PNP transistors for relay switching resistor logic circuits and general purpose applications. 2.54 (0.100) 2 1 0.74 (0.029) 1.14 (0.045) 0.71 (0.028) 0.86 (0.034) 3 45° TO39 PACKAGE (TO-205AD) Underside View Pin 1 = Emitter Pin 2 = Base Pin 3 = Collector ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated) VCB VCE VEB ICM IC(AV) IBM IB(AV) IEM IE(AV) PTOT Collector – Base Voltage Collector – Emitter Voltage Emitter – Base Voltage Collector Current Collector Current ave Over any 20ms Base Current Base Current ave Over any 20ms Emitter Current Emitter Current ave Over any 20ms Total Power Dissipation 25V 25V 16V 100mA 30mA 30mA 15mW 100mA 65mA 230mW Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Document Number 3080 Issue 1 BCY39A THERMAL CHARACTERISTICS CHARACTERISTICS θj-amb θj-case Junction to Ambient Junction to Case 0.3°C/mW 0.12°C/mW ELECTRICAL CHARACTERISTICS (Tcase = 25°C unless otherwise stated) Parameter ICBO Collector Cut-off Current Test Conditions VCB = -6V VCB = -6V Tamb = 100°C VEB = -6V IC = 0 IC = 0 VCE = -1V VCE = - 1V IB = 15mA IB = - 1V VCB = 0 VCE = -2V Rs = 500Ω VCE = -6V VCE = -6V IE = 0 IE = 0 Min. Typ. 1 0.1 1 0.1 Max. Unit 100 2.5 100 2.5 nA µA nA µA IEBO Emitter Cut-off Current VEB = -6V Tamb = 100°C IC = 30mA 12 10 30 50 15 -0.46 -1.5 -1.1 -1.9 14 8 V mA dB 100 — MHz — hFE VCE(sat) VBE IB NF hfe fT DC Current Gain IC = 150mA ICM = 300mA VCE = - 6V Collector – Emitter Saturation Voltage IC = 150mA Base – Emitter Voltage Base – Current Noise Figure Small Signal Current Gain Transistion Frequency IC = 150mA IE = 150mA IC = 500µA f = 1kc/s IC = 10mA f = 1kc/s IC = 1mA 3 15 0.45 35 1.5 *Pulse Test : Pulse Width < 300µs, Duty Cycle < 2% Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Document Number 3080 Issue 1