UCLAMP0511P

μClampTM 1-Line ESD protection PROTECTION PROTECTION PRODUCTS - MicroClamp Description The μClamp series of TVS arrays are designed to protect sensitive electronics from damage or latch-up due to ESD. It is designed to replace multilayer varistors (MLVs) in portable applications. It features large cross-sectional area junctions for conducting high transient currents. It offers superior electrical characteristics such as lower clamping voltage and no device degradation when compared to MLVs. They offer desirable characteristics for board level protection including fast response time, low operating and clamping voltage, and no device degradation. The μClampTM0511P is in a 2-pin, RoHS/WEEE compliant, SLP1006P2 package. It measures 1.0 x 0.6 x 0.5mm. The leads are spaced at a pitch of 0.65mm and are finished with lead-free NiPdAu. Each device will protect one bidirectional line operating at ±5 volts. It gives the designer the flexibility to protect single lines in applications where arrays are not practical. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4 (±15kV air, ±8kV contact discharge). The combination of small size and high ESD surge capability makes them ideal for use in portable applications such as cellular phones, digital cameras, and MP3 players. TM uClamp0511P Features Transient protection for data lines to IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) 40A (tp = 5/50ns) Cable Discharge Event (CDE) Ultra-small package (1.0 x 0.6 x 0.5mm) Protects one I/O or power line Low clamping voltage Working voltage: 5V Low leakage current Solid-state silicon-avalanche technology Mechanical Characteristics SLP1006P2 package Molding compound flammability rating: UL 94V-0 Marking : Marking code Packaging : Tape and Reel Lead Finish: NiPdAu RoHS/WEEE Compliant Applications Cellular Handsets & Accessories Cordless Phones Personal Digital Assistants (PDAs) Notebooks & Handhelds Portable Instrumentation Digital Cameras Peripherals MP3 Players Dimensions 1.0 0.60 0.65 Schematic & PIN Configuration 2 1 SLP1006P2 (Bottom View) 1 www.semtech.com 0.50 Maximum Dimensions (mm) Revision 8/15/2008 uClamp0511P PROTECTION PRODUCTS Absolute Maximum Rating R ating Peak Pulse Power (tp = 8/20μs) Maximum Peak Pulse Current (tp = 8/20μs) ESD p er IEC 61000-4-2 (Air) ESD p er IEC 61000-4-2 (Contact) Op erating Temp erature Storage Temp erature Symbol Pp k Ip p VESD TJ TSTG Value 170 12 +/- 15 +/- 8 -55 to +125 -55 to +150 Units Watts A mp s kV °C °C Electrical Characteristics (T=25oC) Parameter Reverse Stand-Off Voltage Reverse Breakdown Voltage Reverse Leakage Current Clamping Voltage Clamping Voltage Junction Capacitance Symbol VRWM V BR IR VC VC Cj Conditions Pin 1 to 2 or 2 to 1 It = 1mA Pin 1 to 2 or 2 to 1 VRWM = 5V, T=25°C Pin 1 to 2 or 2 to 1 IPP = 1A, tp = 8/20μs Pin 1 to 2 or 2 to 1 IPP = 12A, tp = 8/20μs Pin 1 to 2 or 2 to 1 VR = 0V, f = 1MHz Pin 1 to 2 or 2 to 1 6 8 0.025 Minimum Typical Maximum 5 10 1 11 14 75 Units V V μA V V pF © 2008 Semtech Corp. 2 www.semtech.com uClamp0511P PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time 10 % of Rated Power or I PP 110 100 90 80 70 60 50 40 30 20 10 0 Power Derating Curve Peak Pulse Power - P PP (kW) 1 0.1 0.01 0.1 1 10 Pulse Duration - tp (us) 100 1000 0 25 50 75 100 125 150 Ambient Temperature - TA (oC) Clamping Voltage vs. Peak Pulse Current Peak Pulse Current vs. Clamping Voltage 14 12 Clamping Voltage - VC (V) 10 8 6 4 2 0 0 2 4 6 8 10 Peak Pulse Current - IPP (A) 12 14 16 Waveform Parameters: tr = 8μs td = 20μs ESD Clamping (8kV Contact per IEC 61000-4-2) Junction Capacitance vs. Reverse Voltage 1.1 1 0.9 0.8 CJ(VR) / CJ(VR=0) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 1 2 3 Reverse Voltage - VR (V) 4 5 f = 1 MHz Note: Data is taken with a 10x attenuator © 2008 Semtech Corp. 3 www.semtech.com uClamp0511P PROTECTION PRODUCTS Applications Information Device Connection Options These TVS diodes are designed to protect one data, I/O, or power supply line. The device is bidirectional and may be used on lines where the signal polarity can go above abd below ground. Circuit Board Layout Recommendations for Suppression of ESD. Good circuit board layout is critical for the suppression of ESD induced transients. The following guidelines are recommended: Place the TVS near the input terminals or connectors to restrict transient coupling. Minimize the path length between the TVS and the protected line. Minimize all conductive loops including power and ground loops. The ESD transient return path to ground should be kept as short as possible. Never run critical signals near board edges. Use ground planes whenever possible. Circuit Diagram © 2008 Semtech Corp. 4 www.semtech.com uClamp0511P PROTECTION PRODUCTS Applications Information - Spice Model Figure 1 - uClamp0511P Spice Model Table 1 - μClamp0511P Spice Parameters Parameter IS BV VJ RS IBV CJO TT M N EG Unit Amp Volt Volt O hm Amp Farad sec --eV D1 (T VS) 1.48E-14 7.3 0 .7 0.157 1 E -3 85E-12 2.541E-9 0.126 1.1 1.11 D2 (T VS) 1.48E-14 7.3 0.7 0.157 1E-3 8 5 E -1 2 2.541E-9 0.126 1.1 1.11 © 2008 Semtech Corp. 5 www.semtech.com uClamp0511P PROTECTION PRODUCTS Outline Drawing - SLP1006P2 A D B E DIMENSIONS INCHES MILLIMETERS DIM MIN NOM MAX MIN NOM MAX A A1 b D E e L R N aaa bbb .016 .020 .022 .000 .001 .002 .018 .020 .022 .035 .039 .043 .020 .024 .028 .026 BSC .008 .010 .012 .002 .004 .006 2 .003 .004 0.40 0.50 0.55 0.00 0.03 0.05 0.45 0.50 0.55 0.90 1.00 1.10 0.50 0.60 0.70 0.65 BSC 0.20 0.25 0.30 0.05 0.10 0.15 2 0.08 0.10 TOP VIEW A aaa C A1 PIN 1 ID R bxN bbb CAB 2x L e C SEATING PLANE BOTTOM VIEW NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). Land Pattern - SLP1006P2 Y (C) G Z DIMENSIONS DIM C G X Y Z INCHES (.033) .012 .024 .022 .055 MILLIMETERS (0.85) 0.30 0.60 0.55 1.40 X NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. © 2008 Semtech Corp. 6 www.semtech.com uClamp0511P PROTECTION PRODUCTS Marking Code Ordering Information Part Number Qty per Reel 3,000 Reel Size 7 Inch O PIN 1 ID Tape and Reel Specification uClamp0511P.TCT MicroClamp, uClamp and μClamp are marks of Semtech Corporation A0 0.69 +/-0.10 mm B0 1.19 +/-0.10 mm K0 0.66 +/-0.10 mm Tape Width B, (Max) D 1.5 + 0.1 mm - 0.0 mm (0.59 +.005 - .000) D1 E 1.750±.10 mm (.069±.004) F P 4.0±0.10 mm (.157±.004) P0 4.0±0.1 mm (.157±.004) P2 T W 8.0 mm + 0.3 mm - 0.1 mm (.312±.012) 8 mm 4.2 mm (.165) 0.4 mm ±0.25 (.031) 3.5±0.05 mm (.138±.002) 2.0±0.05 mm (.079±.002) 0.254±0.02 mm (.016) Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 www.semtech.com © 2008 Semtech Corp. 7