SGM2006-1.8

SGM2006/A GENERAL DESCRIPTION The SGM2006/A series low-power, low-noise, low-dropout, CMOS linear voltage regulators operate from a 2.5V to 5.5V input and deliver up to 150mA. They are the perfect choice for low voltage, low power applications. An ultra low ground current ( 150µA at 150mA output ) makes these part attractive for battery operated power systems. The SGM2006/A series also offer ultra low dropout voltage (150mV at 150mA output) to prolong battery life in portable electronics. Systems requiring a quiet voltage source, such as RF applications, will benefit from the SGM2006/A series’ ultra low output noise (30µVRMS) and high PSRR. An external noise bypass capacitor connected to the device’s BP pin can further reduce the noise level. The output voltage is preset to voltages in the range of 1.5V to 5.0V. Other features include a 10nA logic-controlled shutdown mode, foldback current limit and thermal shutdown protection. Devices come in 5-pin SOT23 package. Low Power, Low Dropout, 150mA, RF - Linear Regulators FEATURES - Low Output Noise: 30µVRMS typ(10Hz to 100KHz) - Ultra-Low Dropout Voltage: 150mV at 150mA output - Low 77µA No-Load Supply Current - Low 150µA Operating Supply Current - at 150mA Output High PSRR: 73dB at 1KHz Thermal-Overload Protection Output Current Limit Preset Output Voltages (±2.7% Accuracy) 10nA Logic-Controlled Shutdown Available in Multiple Output Voltage Versions Fixed Outputs of 1.8V, 2.5V, 2.7V, 2.8V, 2.85V, 2.9V, 3.0V, 3.3Vand 3.6V Adjustable Output from 1.5V to 5.0V PIN CONFIGURATIONS（TOP VIEW） SGM2006/A IN 1 2 5 OUT APPLICATIONS Cellular Telephones Cordless Telephones PHS Telephones PCMCIA Cards Modems MP3 Player Hand-Held Instruments Palmtop Computers Electronic Planners Portable/Battery-Powered Equipment GND EN 3 SOT23-5 4 BP/FB Shengbang Microelectronics Co, Ltd Tel: 86/451/84348461 www.sg-micro.com REV. C ORDERING INFORMATION MODEL SGM2006-1.8 SGM2006-2.5 SGM2006-2.7 SGM2006-2.8 SGM2006-2.85 SGM2006-2.9 SGM2006-3.0 SGM2006-3.3 SGM2006-3.6 SGM2006A VOUT(V) 1.8V 2.5V 2. 7V 2.8V 2.85V 2.9V 3.0V 3.3V 3.6V adjustable PINPACKAGE SPECIFIED TEMPERATURE RANGE ORDERING NUMBER SGM2006-1.8XN5/TR SGM2006-2.5XN5/TR SGM2006-2. 7XN5/TR SGM2006-2.8XN5/TR SGM2006-2.85XN5/TR SGM2006-2.9XN5/TR SGM2006-3.0XN5/TR SGM2006-3.3XN5/TR SGM2006-3.6XN5/TR SGM2006-XN5/TR PACKAGE MARKING X618 X625 X627 X628 X62J X629 X630 X633 X636 X6AA PACKAGE OPTION SOT23-5 SOT23-5 SOT23-5 SOT23-5 SOT23-5 SOT23-5 SOT23-5 SOT23-5 SOT23-5 SOT23-5 - 40°C to +125°C - 40°C to +125°C - 40°C to +125°C - 40°C to +125°C - 40°C to +125°C - 40°C to +125°C - 40°C to +125°C - 40°C to +125°C - 40°C to +125°C - 40°C to +125°C Tape and Reel, 3000 Tape and Reel, 3000 Tape and Reel, 3000 Tape and Reel, 3000 Tape and Reel, 3000 Tape and Reel, 3000 Tape and Reel, 3000 Tape and Reel, 3000 Tape and Reel, 3000 Tape and Reel, 3000 ABSOLUTE MAXIMUM RATINGS IN to GND.....................................................................- 0.3V to +6V Output Short-Circuit Duration ...........................................Infinite EN to GND...................................................................- 0.3V to +6V OUT, BP/FB to GND......................................- 0.3V to (VIN + 0.3V) Power Dissipation, PD @ TA = 25℃ SOT23-5 .....................................................................................0.4W Package Thermal Resistance SOT23-5, θJA....................................................................... 250℃/W Operating Temperature Range...........................- 40°C to +125°C Junction Temperature...........................................................+150°C Storage Temperature.............................................- 65°C to +150°C Lead Temperature (soldering, 10s).......................................260°C ESD Susceptibility HBM..........................................................................................4000V MM..............................................................................................400V Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. PIN DESCRIPTION PIN 1 2 3 4 4 5 NAME IN GND EN BP FB OUT FUNCTION Regulator Input. Supply voltage can range from 2.5V to 5.5V. Bypass with a 1µF capacitor to GND. Ground. Shutdown Input. A logic low reduces the supply current to 10nA. Connect to IN for normal operation. Reference-Noise Bypass(fixed voltage version only). Bypass with a low-leakage 0.01µF ceramic capacitor for reduced noise at the output. Adjustable voltage version only—this is used to set the output voltage of the device. Regulator Output. 2 SGM2006/A ELECTRICAL CHARACTERISTICS PARAMETER Input Voltage Output Voltage Accuracy(1) Maximum Output Current Current Limit Ground Pin Current Dropout Voltage (2) Line Regulation(1) Load Regulation Output Voltage Noise Power Supply Rejection Rate SHUTDOWN EN Input Threshold EN Input Bias Current Shutdown Supply Current Shutdown Exit Delay(3) THERMAL PROTECTION Thermal Shutdown Temperature Thermal Shutdown Hysteresis TSHDN ΔTSHDN VIH VIL IB(SHDN) IQ(SHDN) VIN = 2.5V to 5.5V EN = 0V and EN = 5.5V EN = 0.4V CBP = 0.01µF COUT = 1µF, No load ΔVLNR ΔVLDR ILIM IQ No load, EN = 2V IOUT = 150mA, EN = 2V IOUT = 1mA IOUT = 150mA SYMBOL VIN (VIN = VOUT (NOMINAL) + 0.5V (1), TA = - 40°C to +125°C, unless otherwise noted. Typical values are at TA = + 25°C.) CONDITIONS IOUT =1mA to150mA, TA = +25°C VOUT + 0.5V≤VIN≤ 5.5V MIN 2.5 -2.7 150 160 600 77 150 1 150 0.03 0.0008 30 78 73 2.0 0.4 TA = +25°C TA = +125°C TA = +25°C TA = +125°C TA = +25°C 0.01 0.01 0.01 0.01 30 1 1 190 0.15 0.002 145 TYP MAX 5.5 +2.7 UNITS V % mA mA µA mV %/V %/mA µVRMS dB dB VIN = 2.5V or (VOUT + 0.5V) to 5.5V, IOUT = 1mA IOUT = 0.1mA to 150mA, COUT = 1µF f = 10Hz to 100KHz, CBP = 0.01µF, COUT = 10µF CBP = 0.1µF, ILOAD = 50mA, COUT = 1µF f = 100Hz, f = 1KHz, en PSRR V µA µA µs 160 15 ℃ ℃ Specifications subject to change without notice. Note 1: VIN = VOUT(NOMINAL) + 0.5V or 2.5V, whichever is greater. Note 2: The dropout voltage is defined as VIN - VOUT, when VOUT is 100mV below the value of VOUT for VIN = VOUT + 0.5V. (Only applicable for VOUT = +2.5V to +5.0V.) Note 3: Time needed for VOUT to reach 95% of final value. ３ SGM2006/A TYPICAL OPERATION CIRCUIT INPUT 2.5V TO 5.5V IN CIN 1μF ON OFF OUT OUTPUT COUT 1μ F INPUT 2.5V TO 5.5V IN OUT OUTPUT SGM 2006A EN GND FB R1 CIN 1μF ON OFF SGM 2006 EN GND BP COUT 1μF R2 CBP 0.01μF Adjustable Voltage Version Fixed Voltage Version Standard 1% Resistor Values for Common Output Voltages of Adjustable Voltage Version VOUT(V) 1.5 1.8 2.5 2.7 2.8 2.85 2.9 3.0 3.3 3.6 R1(kΩ) 13 28 63.4 56 78.7 80.6 75 88.7 95.3 130 R2(kΩ) 61.9 61.9 61.9 47 61.9 61.9 56 61.9 57.6 68 Note: VOUT = (R1 + R2)/ R2 ×1.233 ４ SGM2006/A TYPICAL OPERATING CHARACTERISTICS VIN = VOUT(NOMINAL) + 0.5V or 2.5V (whichever is greater), CIN = 1µF, COUT = 1µF, CBP = 0.01µF, TA = +25℃, unless otherwise noted. Output Voltage vs.Load Current 2.9 3.4 Output Voltage vs.Load Current Output Voltage(V) Output Voltage(V) VOUT = 2.8V 2.85 3.35 2.8 3.3 2.75 3.25 VOUT = 3.3V 3.2 2.7 0 50 100 Load Current(mA) 150 0 50 100 Load Current(mA) 150 Ground Pin Current vs.Load Current 160 150 Ground Pin Current(µA) Ground Pin Current(µA) 200 Ground Pin Current vs.Input Voltage VOUT = 2.8V 160 Iload = 50mA 140 130 120 110 100 90 80 70 60 0 50 100 Load Current(mA) 150 VOUT = 2.8V VOUT = 3.3V 120 80 No Load 40 0 0 1 2 3 4 Input Voltage(V) 5 6 Ground Pin Current vs.Input Voltage 200 VOUT = 3.3V Ground Pin Current(µA) 160 120 80 40 0 0 1 2 3 4 Input Voltage(V) 5 6 Iload = 50mA Output Voltage(V) 5 4 3 2 1 0 0 6 Output Voltage vs.Input Voltage No Load VOUT = 3.3V No Load VOUT = 2.8V 1 2 3 4 Input Voltage(V) 5 6 ５ SGM2006/A TYPICAL OPERATING CHARACTERISTICS VIN = VOUT(NOMINAL) + 0.5V or 2.5V (whichever is greater), CIN = 1µF, COUT = 1µF, CBP = 0.01µF, TA = +25℃, unless otherwise noted. Output Voltage vs.Temperature 2.9 ILOAD = 150mA Output Voltage(V) Output Voltage vs.Temperature 3.4 ILOAD = 150mA Output Voltage(V) 3.35 2.85 2.8 3.3 2.75 VOUT = 2.8V 2.7 -40 -20 0 20 40 60 80 Temperature(℃) 100 120 140 3.25 VOUT = 3.3V 3.2 -40 -20 0 20 40 60 80 Temperature(℃) 100 120 140 Ground Pin Current vs.Temperature 260 240 Ground Pin Current( μA) 220 Dropout Voltage vs.Load Current 220 200 180 Dropout Voltage(mV) 160 140 120 100 80 60 40 20 0 0 15 30 VOUT = 2.8V 45 60 75 90 105 120 135 150 Load Current(mA) TA = -40℃ TA = +125℃ 200 180 160 140 120 100 80 60 -40 -20 0 20 40 60 80 Temperature(℃) 100 120 140 ILOAD = 150mA VOUT = 2.8V VOUT = 3.3V TA = +85℃ TA = +25℃ Dropout Voltage vs.Load Current 180 160 Dropout Voltage(mV) TA = +85℃ TA = +25℃ TA = -40℃ Current limit(mA) TA = +125℃ Current limit vs.Temperature 1000 900 800 700 600 500 400 300 200 100 -40 -20 0 20 40 60 80 Temperature(℃) 100 120 140 VOUT = 2.8V VOUT = 3.3V 140 120 100 80 60 40 20 0 0 15 30 45 VOUT = 3.3V 60 75 90 105 120 135 150 Load Current(mA) ６ SGM2006/A TYPICAL OPERATING CHARACTERISTICS VIN = VOUT(NOMINAL) + 0.5V or 2.5V (whichever is greater), CIN = 1µF, COUT = 1µF, CBP = 0.01µF, TA = +25℃, unless otherwise noted. ７ SGM2006/A TYPICAL OPERATING CHARACTERISTICS VIN = VOUT(NOMINAL) + 0.5V or 2.5V (whichever is greater), CIN = 1µF, COUT = 1µF, CBP = 0.01µF, TA = +25℃, unless otherwise noted. Power-Supply Rejection Ratio vs.Frequency 100 90 80 PSRR(dB) 70 60 50 40 30 20 0.01 COUT = 1μF 0.1 1 10 Frequency(kHz) 100 1000 COUT = 10μF Output Noise Spectral Density vs.Frequency 10 Output Noise Spectral Density (μV/√Hz) CBP = 0.1μF ILOAD = 50mA VIN = VOUT+1V CBP = 0.01μF ILOAD = 50mA 1 COUT = 1μF 0.1 COUT = 10μF 0.01 0.01 0.1 1 10 100 1000 Frequency(kHz) Output Noise vs.Load Current 50 45 Output Noise(µVRMS) 40 35 30 25 20 15 10 5 0 1 10 100 Load Current(mA) 1000 VOUT = 2.8V f = 10Hz to 100kHz CBP = 0.01μF COUT = 10μF VOUT = 3.3V ８ SGM2006/A Application Notes When LDO is used in handheld products, Attention must be paid to voltage spike which would damage SGM2006. In such applications, voltage spike will be generated at changer interface and VBUS pin of USB interface when changer adapters and USB equipments are hot-inserted. Besides this, handheld products will be tested on the production line on the condition of no battery. Test Engineer will apply power from the connector pin which connects with positive pole of the battery. When external power supply is turned on suddenly, the voltage spike will be generated at the battery connector. The voltage spike will be very high, it always exceeds the absolute maximum input voltage (6.0V) of LDO. In order to get robust design. Design Engineer needs to clear up this voltage spike. Zener diode is a cheap and effective solution to eliminate such voltage spike. For example, BZM55B5V6 is a 5.6V small package Zener diode which can be used to remove voltage spike in cell phone design. The schematic is shown in below: Vcc Input BZM55B5V6 1uF C1 1 IN SGM2006 EN 3 GND 2 BP/FP 4 VOUT 5 C2 4.7uF VOUT 0.01uF Control ９ SGM2006/A PACKAGE OUTLINE DIMENSIONS SOT23-5 D b L 0 θ 0.20 Symbol A A1 Dimensions In Millimeters Min 1.050 0.000 1.050 0.300 0.100 2.820 1.500 2.650 1.800 0.300 0° Dimensions In Inches Min 0.041 0.000 0.041 0.012 0.004 0.111 0.059 0.104 0.071 0.012 0° Max 1.250 0.100 1.150 0.400 0.200 3.020 1.700 2.950 2.000 0.600 8° Max 0.049 0.004 0.045 0.016 0.008 0.119 0.067 0.116 0.079 0.024 8° E1 A2 b c E L e e1 A1 D C E E1 e e1 0.950TYP 0.700REF 0.037TYP 0.028REF A2 L L1 θ A １０ SGM2006/A REVISION HISTORY Location 12/06— Data Sheet changed from REV. A to REV. B Changed to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Added Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Page 03/07— Data Sheet changed from REV. B to REV. C Changed to TYPICAL OPERATING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Shengbang Microelectronics Co, Ltd Unit 3, ChuangYe Plaza No.5, TaiHu Northern Street, YingBin Road Centralized Industrial Park Harbin Development Zone Harbin, HeiLongJiang 150078 P.R. China Tel.: 86-451-84348461 Fax: 86-451-84308461 www.sg-micro.com １１ SGM2006/A