SGM2202-5.0YN5G/TR

SGM2202 150mA, High PSRR, High Voltage Regulator GENERAL DESCRIPTION FEATURES The SGM2202 is a high voltage and high PSRR linear ● High Input Voltage: Up to 36V regulator. It is capable of supplying 150mA output ● Fixed Output Voltages: 2.5V, 2.8V, 3.0V, 3.3V, 5.0V current. The operating input voltage is up to 36V. The ● Adjustable Output Voltages: 0.8V to 13.2V output voltage range is from 2.5V to 5.0V in fixed output ● 150mA Guaranteed Output Current version. For adjustable output version, the output ● Output Voltage Accuracy: ±2.5% at +25℃ voltage can be adjusted from 0.8V to 13.2V by using ● High PSRR: 40dB (TYP) at 1kHz external resistors. ● Low Dropout Voltage ● Low Power Consumption: 4.2μA (TYP) Other features include logic-controlled shutdown mode, ● Shutdown Supply Current: 1.5μA (TYP) current limit and thermal shutdown protection. ● Low Temperature Coefficient The SGM2202 is available in Green SOT-23-5 and ● Thermal Shutdown Protection SOT-23-6 packages. It operates over an operating ● Output Current Limit temperature range of -40℃ to +85℃. ● -40℃ to +85℃ Operating Temperature Range ● Available in Green SOT-23-5 and SOT-23-6 Packages APPLICATIONS Palmtops High-Power Boost Applications Power Source for Battery-Powered Equipment Home Electric/Electronic Appliances TYPICAL APPLICATION VIN VIN CIN 1μF VOUT VOUT SGM2202 ON EN COUT 1μF BP GND OFF CBP 0.01μF Figure 1. Fixed Voltage Typical Application Circuit VIN CIN 1μF OFF EN BP CBP 0.01μF VOUT VOUT VIN ON SGM2202-ADJ GND R1 FB COUT 1μF R2 Figure 2. Adjustable Voltage Typical Application Circuit SG Micro Corp www.sg-micro.com OCTOBER 2020 – REV. A. 2 SGM2202 150mA, High PSRR, High Voltage Regulator PACKAGE/ORDERING INFORMATION SPECIFIED PACKAGE TEMPERATURE DESCRIPTION RANGE MODEL VOUT (V) ORDERING NUMBER PACKAGE MARKING PACKING OPTION SGM2202-2.5 2.5 SOT-23-5 -40℃ to +85℃ SGM2202-2.5YN5G/TR G1DXX Tape and Reel, 3000 SGM2202-2.8 2.8 SOT-23-5 -40℃ to +85℃ SGM2202-2.8YN5G/TR SX5XX Tape and Reel, 3000 SGM2202-3.0 3.0 SOT-23-5 -40℃ to +85℃ SGM2202-3.0YN5G/TR SX6XX Tape and Reel, 3000 SOT-23-5 (L-Type) -40℃ to +85℃ SGM2202-3.0YN5LG/TR G12XX Tape and Reel, 3000 SGM2202-3.3 3.3 SOT-23-5 -40℃ to +85℃ SGM2202-3.3YN5G/TR SX8XX Tape and Reel, 3000 SGM2202-5.0 5.0 SOT-23-5 -40℃ to +85℃ SGM2202-5.0YN5G/TR G3DXX Tape and Reel, 3000 SGM2202-ADJ Adjustable SOT-23-6 -40℃ to +85℃ SGM2202-ADJYN6G/TR SVFXX Tape and Reel, 3000 MARKING INFORMATION NOTE: XX = Date Code. YYY X X Date Code - Month Date Code - Year Serial Number Green (RoHS & HSF): SG Micro Corp defines "Green" to mean Pb-Free (RoHS compatible) and free of halogen substances. If you have additional comments or questions, please contact your SGMICRO representative directly. ABSOLUTE MAXIMUM RATINGS VIN, EN to GND ................................................. -0.3V to 44V VOUT to GND .......................... -0.3V to Min(VIN + 0.3V, 15V) BP, FB to GND .......................... -0.3V to Min(VIN + 0.3V, 6V) Power Dissipation, PD @ TA = +25℃ SOT-23-5, SOT-23-5 (L-Type) ................................... 0.517W SOT-23-6 ................................................................... 0.558W Package Thermal Resistance SOT-23-5, SOT-23-5 (L-Type), θJA .......................... 242℃/W SOT-23-6, θJA .......................................................... 224℃/W Junction Temperature .................................................+150℃ Storage Temperature Range ....................... -65℃ to +150℃ Lead Temperature (Soldering, 10s) ............................+260℃ ESD Susceptibility HBM ............................................................................. 4000V MM ................................................................................. 150V CDM ............................................................................ 1000V RECOMMENDED OPERATING CONDITIONS Input Voltage Range ............................................2.7V to 36V Operating Temperature Range ...................... -40℃ to +85℃ SG Micro Corp www.sg-micro.com OVERSTRESS CAUTION Stresses beyond those listed in Absolute Maximum Ratings may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Functional operation of the device at any conditions beyond those indicated in the Recommended Operating Conditions section is not implied. ESD SENSITIVITY CAUTION This integrated circuit can be damaged if ESD protections are not considered carefully. SGMICRO recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because even small parametric changes could cause the device not to meet the published specifications. DISCLAIMER SG Micro Corp reserves the right to make any change in circuit design, or specifications without prior notice. OCTOBER 2020 2 SGM2202 150mA, High PSRR, High Voltage Regulator PIN CONFIGURATIONS SGM2202-Fixed Output (TOP VIEW) VIN 1 GND 2 EN 3 5 4 SGM2202-3.0 (Only) (TOP VIEW) VOUT BP VIN 1 GND 2 EN 3 SOT-23-5 5 VOUT 4 NC SOT-23-5 (L-Type) SGM2202-ADJ (TOP VIEW) VIN 1 6 VOUT GND 2 5 BP EN 3 4 FB SOT-23-6 PIN DESCRIPTION PIN NAME FUNCTION 1 VIN Input Supply Voltage Pin. It is recommended to use a 1μF or larger ceramic capacitor from VIN pin to ground. This ceramic capacitor should be placed as close as possible to IN pin. 2 2 GND Ground. 3 3 3 EN ‒ ‒ 4 FB 4 ‒ 5 BP ‒ 4 ‒ NC 5 5 6 VOUT SOT-23-5 SOT-23-5 (L-Type) SOT-23-6 1 1 2 SG Micro Corp www.sg-micro.com Enable Pin. Drive EN high to turn on the regulator. Drive EN low to turn off the regulator. This pin must be connected to VIN pin if enable functionality is not used. Feedback Voltage Input Pin. Connect this pin to the midpoint of an external resistor divider to adjust the output voltage. Place the resistors as close as possible to this pin. Reference-Noise Bypass Pin. Bypass with an external capacitor CBP can reduce output noise to very low level. The capacitor is recommended to be placed very close to the pin for high PSRR. Not Connected. Regulator Output Pin. It is recommended to use an output capacitor with effective capacitance in the range of 1μF to 10μF. The capacitor should be located very close to this pin. OCTOBER 2020 3 SGM2202 150mA, High PSRR, High Voltage Regulator ELECTRICAL CHARACTERISTICS (VIN = 15V, VEN = 2V, CIN = COUT = 1μF, CBP = 0.01µF, Full = -40℃ to +85℃, typical values are at TA = +25℃, unless otherwise noted.) PARAMETER Input Voltage Range SYMBOL VIN Output Voltage Accuracy CONDITIONS 2.7 32 2.7 36 IOUT = 1mA +25℃ -2.5 2.5 % +25℃ 15 nA SGM2202-ADJ, VFB = VOUT, IOUT = 1mA SGM2202-ADJ, VFB = 0.9V Full IOUT = 50mA +25℃ VIN = VOUT + 2V or 4V, whichever is greater +25℃ Load Regulation ΔVOUT VIN = VOUT + 2V or 4V, IOUT = 1mA to 150mA Output Voltage Temperature (2) Coefficient ∆VOUT ∆TA × VOUT VOUT = 3.3V, IOUT = 10mA µA 4.2 mA 1300 1840 2380 +25℃ 0.005 0.01 +25℃ 0.005 0.01 24 +25℃ 10 f = 217Hz +25℃ 55 f = 1kHz +25℃ 40 Full 35 VIN = VOUT + 2V or 4V, IOUT = 1mA 5.4 150 Full VIN = VOUT + 2V or 4V to 32V, VOUT < 3.3V IOUT = 1mA VIN = VOUT + 2V to 36V, VOUT ≥ 3.3V IOUT = 1mA V V 6.5 +25℃ IOUT = 150mA, VOUT ≥ 2.5V ∆VOUT ∆VIN × VOUT PSRR 4.2 Full Line Regulation Power Supply Rejection Ratio 0.8 -15 +25℃ No load VDROP UNITS Full IFB (1) MAX Full VFB Dropout Voltage TYP VOUT < 3.3V FB Input Current Maximum Output Current MIN VOUT ≥ 3.3V Feedback Voltage Ground Pin Current TEMP mV %/V mV dB ppm/℃ Shutdown EN Input Threshold EN Input Bias Current Shutdown Supply Current Start-Up Time (3) VIH VIL VIN = 2.7V to 36V Full 1.2 Full 0.4 IBH VEN = VIN Full IBL VEN = 0V Full IQ(SHDN) VEN = 0V +25℃ 1.5 tSTR No load +25℃ 5 ms VIN = 2.7V, VEN = 0V, IOUT = -1mA +25℃ 75 Ω RON of Discharge MOSFET 0.02 -1 1 V 1 2 μA μA Thermal Protection Thermal Shutdown Temperature TSHDN 150 ℃ Thermal Shutdown Hysteresis ΔTSHDN 20 ℃ NOTES: 1. The dropout voltage is defined as the difference between VIN and VOUT when VOUT falls to 95% × VOUT for VIN = VOUT + 2V. 2. Output voltage temperature coefficient is defined as the worst-case voltage change divided by the total temperature range. 3. Time needed for VOUT to reach 90% of final value. SG Micro Corp www.sg-micro.com OCTOBER 2020 4 SGM2202 150mA, High PSRR, High Voltage Regulator TYPICAL PERFORMANCE CHARACTERISTICS TA = +25℃, VIN = 5.3V, VEN = 2V, VOUT = 3.3V, CIN = COUT = 1μF, CBP = 0.01µF, unless otherwise noted. Load-Transient Response Line-Transient Response VIN = 5.3V to 6.3V, IOUT = 50mA IOUT = 10mA to 100mA VIN 100mV/div 50mA/div IOUT 1V/div 100mV/div VOUT VOUT Time (2ms/div) Time (1ms/div) Power-Up/Power-Down Output Waveform Power Ramp-Up/Ramp-Down Output Waveform VIN = 0V to 5.3V, IOUT = 50mA VIN = 0V to 6.3V, IOUT = 50mA 2V/div 2V/div VIN VIN 2V/div VOUT 2V/div VOUT Time (4ms/div) Time (5ms/div) Output Short Waveform Thermal Protection Waveform 1V/div 2V/div 100mA/div 100mA/div VOUT VOUT IOUT IOUT Time (50ms/div) SG Micro Corp www.sg-micro.com Time (4ms/div) OCTOBER 2020 5 SGM2202 150mA, High PSRR, High Voltage Regulator TYPICAL PERFORMANCE CHARACTERISTICS (continued) TA = +25℃, VIN = 5.3V, VEN = 2V, VOUT = 3.3V, CIN = COUT = 1μF, CBP = 0.01µF, unless otherwise noted. Pulse Load Current Output Waveform Power Supply Rejection Ratio vs. Frequency 100 80 1V/div PSRR (dB) VOUT 100mA/div IOUT IOUT = 10mA ∆VRIP = 0.2VP-P 60 40 20 0 0.01 Time (20ms/div) Dropout Voltage vs. Temperature 10 100 Dropout Voltage vs. Output Current 1600 IOUT = 50mA Dropput Voltage (mV) Dropout Voltage (mV) 1 Frequency (kHz) 600 550 0.1 500 450 400 1200 800 400 350 300 -50 0 -25 0 25 50 75 100 Temperature (℃) 0 25 50 75 100 125 150 Output Current (mA) Ground Pin Current vs. Temperature 5.5 Ground Pin Current (μA) V IN = 36V, No Load 5.0 4.5 4.0 3.5 3.0 -50 -25 0 25 50 75 100 Temperature (℃) SG Micro Corp www.sg-micro.com OCTOBER 2020 6 SGM2202 150mA, High PSRR, High Voltage Regulator APPLICATION INFORMATION Input Capacitor Selection (CIN) The input decoupling capacitor is necessary to be connected as close as possible to the VIN pin for ensuring the device stability. 1μF or larger X7R or X5R ceramic capacitor is selected to get good dynamic performance. When VIN is required to provide large current instantaneously, a large effective input capacitor is required. Multiple input capacitors can limit the input tracking inductance. Adding more input capacitors is available to restrict the ringing and to keep it below the device absolute maximum ratings. Output Capacitor Selection (COUT) The output decoupling capacitor should be located as close as possible to the VOUT pin. 1μF or larger X7R or X5R ceramic capacitor is selected to get good dynamic performance. The minimum effective capacitance of COUT that SGM2202 can remain stable is 0.5μF. For ceramic capacitor, temperature, DC bias and package size will change the effective capacitance, so enough margin of COUT must be considered in design. Larger capacitance and lower ESR COUT will help improve the load transient response and increase the high frequency PSRR. Thermal Shutdown The SGM2202 can detect the temperature of die. When the die temperature exceeds the threshold value of thermal shutdown, the SGM2202 will be in shutdown state and it will remain in this state until the die temperature decreases to +130℃. REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. OCTOBER 2020 ‒ REV.A.1 to REV.A.2 Page Updated Package/Ordering Information section .......................................................................................................................................................2 Changes from Original (APRIL 2017) to REV.A Page Changed from product preview to production data .................................................................................................................................................All SG Micro Corp www.sg-micro.com OCTOBER 2020 7 PACKAGE INFORMATION PACKAGE OUTLINE DIMENSIONS SOT-23-5 1.90 D e1 E1 2.59 E 0.99 b e 0.69 0.95 RECOMMENDED LAND PATTERN (Unit: mm) L A A1 θ A2 Symbol Dimensions In Millimeters MIN MAX c 0.2 Dimensions In Inches MIN MAX A 1.050 1.250 0.041 0.049 A1 0.000 0.100 0.000 0.004 A2 1.050 1.150 0.041 0.045 b 0.300 0.500 0.012 0.020 c 0.100 0.200 0.004 0.008 D 2.820 3.020 0.111 0.119 E 1.500 1.700 0.059 0.067 E1 2.650 2.950 0.104 0.116 e 0.950 BSC 0.037 BSC e1 1.900 BSC 0.075 BSC SG Micro Corp www.sg-micro.com L 0.300 0.600 0.012 0.024 θ 0° 8° 0° 8° TX00033.000 PACKAGE INFORMATION PACKAGE OUTLINE DIMENSIONS SOT-23-6 D e1 e 2.59 E E1 0.99 b 0.95 0.69 RECOMMENDED LAND PATTERN (Unit: mm) L A A1 θ A2 Symbol Dimensions In Millimeters MIN MAX c 0.2 Dimensions In Inches MIN MAX A 1.050 1.250 0.041 0.049 A1 0.000 0.100 0.000 0.004 A2 1.050 1.150 0.041 0.045 b 0.300 0.500 0.012 0.020 c 0.100 0.200 0.004 0.008 D 2.820 3.020 0.111 0.119 E 1.500 1.700 0.059 0.067 E1 2.650 2.950 0.104 0.116 e 0.950 BSC 0.037 BSC e1 1.900 BSC 0.075 BSC SG Micro Corp www.sg-micro.com L 0.300 0.600 0.012 0.024 θ 0° 8° 0° 8° TX00034.000 PACKAGE INFORMATION TAPE AND REEL INFORMATION REEL DIMENSIONS TAPE DIMENSIONS P2 W P0 Q1 Q2 Q1 Q2 Q1 Q2 Q3 Q4 Q3 Q4 Q3 Q4 B0 Reel Diameter K0 A0 P1 Reel Width (W1) DIRECTION OF FEED NOTE: The picture is only for reference. Please make the object as the standard. KEY PARAMETER LIST OF TAPE AND REEL Reel Diameter Reel Width W1 (mm) A0 (mm) B0 (mm) K0 (mm) P0 (mm) P1 (mm) P2 (mm) W (mm) Pin1 Quadrant SOT-23-5 7″ 9.5 3.20 3.20 1.40 4.0 4.0 2.0 8.0 Q3 SOT-23-6 7″ 9.5 3.17 3.23 1.37 4.0 4.0 2.0 8.0 Q3 SG Micro Corp www.sg-micro.com TX10000.000 DD0001 Package Type PACKAGE INFORMATION CARTON BOX DIMENSIONS NOTE: The picture is only for reference. Please make the object as the standard. KEY PARAMETER LIST OF CARTON BOX Length (mm) Width (mm) Height (mm) Pizza/Carton 7″ (Option) 368 227 224 8 7″ 442 410 224 18 SG Micro Corp www.sg-micro.com DD0002 Reel Type TX20000.000