GW6DMD27NFC

Spec No. Issue DG-127015B 23-Oct-12 S P E C I F I C A T I O N S Product Type ZENIGATA LED Model No. GW6DMD**NFC ** ： 27, 30, 35, 40, 50, 60 ※These specifications contain 20 pages including the cover and appendix. If you have any objections, please contact us before issuing purchasing order. CUSTOMERS ACCEPTANCE Reference DATE: BY: PRESENTED BY: T. Uemura Dept. General Manager REVIEWED BY: PREPARED BY: Development Department Ⅱ Lighting Device Division Electronic Components And Devices Group SHARP CORPORATION Model No. GW6DMD**NFC ● Handle this document carefully for it contains material protected by international copyright law. Any reproduction, full or in part, of this material is prohibited without the express written permission of the company. ● When using the products covered herein, please observe the conditions written herein and the precautions outlined in the following paragraphs. In no event shall the company be liable for any damages resulting form failure to strictly adhere to these conditions and precautions. (1) Please do verify the validity of this part after assembling it in customer’s products, when customer wants to make catalogue and instruction manual based on the specification sheet of this part. (2) The products covered herein are designed and manufactured for the following application areas. When using the products covered herein for the equipment listed in paragraph (3), even for the following application areas, be sure to observe the precautions given in Paragraph (3). Never use the products for the equipment listed in Paragraph (4). ･Office electronics ･Instrumentation and measuring equipment ･Machine tools ･Audiovisual equipment ･Home appliances ･Communication equipment other than for trunk lines (3) These contemplating using the products covered herein for the following equipment which demands high reliability, should first contact a sales representative of the company and then accept responsibility for incorporating into the design fail-safe operation, redundancy, and other appropriate measures for ensuring reliability and safety of the equipment and the overall system. ･Control and safety devices for airplanes, trains, automobiles, and other transportation equipment ･Mainframe computers ･traffic control systems ･Gas leak detectors and automatic cutoff devices ･Rescue and security equipment ･Other safety devices and safety equipment, etc. (4) Do not use the products covered herein for the following equipment which demands extremely high performance in terms of functionality, reliability, or accuracy. ･Aerospace equipment ･Communications equipment for trunk lines ･Control equipment for the nuclear power industry ･Medical equipment related to life support, etc. (5) please direct all queries and comments regarding the interpretation of the above four Paragraphs to a sales representative of the company. ● Please direct all queries regarding the products covered herein to a sales representative of the company. DG-127015B Model No. Page GW6DMD**NFC 1 of 18 GW6DMD**NFC specifications 1. Application These specifications apply to the light emitting diode module Model No. GW6DMD**NFC. [ LED module (InGaN Blue LED chip + Phosphor) ] Main application : Lighting 2. External dimensions and equivalent circuit -------------------------------- Refer to Page 2. 3. Ratings and characteristics --------------------------------------------------- Refer to Page 3 - 4. 3-1. Absolute maximum ratings 3-2. Electro-optical characteristics 3-3. Derating curve 4. Reliability ---------------------------------------------------------------------- Refer to Page 5. 4-1. Test items and test conditions 4-2. Failure criteria 5. Quality level ------------------------------------------------------------------- Refer to Page 6. . 5-1. Applied standard 5-2. Sampling inspection 5-3. Inspection items and defect criteria 6. Supplements------------------------------------------------------------------- Refer to Page 7 - 9. 6-1. Chromaticity rank table 6-2. Packing 6-3. Label 6-4. Indication printed on product 7. Precautions -------------------------------------------------------------------- Refer to Page 10 - 12. 8. Characteristics diagram (TYP.) ---------------------------------------------- Refer to Page 13. DG-127015B Model No. Page GW6DMD**NFC 2 of 18 2. External dimensions and equivalent circuit Unit = mm 24.0 + 0.50 / - 0.10　① ( 18.6 ) Top view ( R8.6 ) 20.0 ( 12.5 ) + 0.50 / - 0.10 ② Side view 1.0 ( 1.8 ) ± 0.1 (Note) Values inside parentheses are reference values. External dimension of ceramic substrate is the indication of maximum length at each side. R Equivalent circuit + connection terminal - connection terminal (Note) 12 series × 10 parallel = 120 pcs of LEDs Unit Material Drawing No. mm Substrate : Alumina Ceramic 52407015 DG-127015B Model No. Page GW6DMD**NFC 3 of 18 3. Ratings and characteristics 3-1. Absolute maximum ratings Item Power Dissipation *1,4 Forward Current *1,4 Reverse Voltage *2,4 Operating Temperature *3 Storage Temperature Symbol P IF VR Topr Tstg Rating 52.0 1300 -15 - 30 ～ + 100 - 40 ～ + 100 Unit W mA V ℃ ℃ *1 Power dissipation and forward current are the value when the module temperature is set lower than the rating by using an adequate heat sink. *2 Voltage resistible at initial connection error (Not dealing with the possibility of always-on reverse voltage.) *3 Case temperature Tc (Refer to measuring point for case temperature in the next page.) Refer to "Derating curve" in the next page as for operating current. *4 Tc = 25 ℃ DG-127015B Model No. Page GW6DMD**NFC 4 of 18 3-2. Electro-optical characteristics (Tj = 90 ℃) Item ** common Forward Voltage *5 Luminous Flux *6 27 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 30 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 35 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 40 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 50 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 60 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Symbol VF Ф x y Ra Ф x y Ra Ф x y Ra Ф x y Ra Ф x y Ra Ф x y Ra Condition IF = 950 mA IF = 950 mA IF = 950 mA IF = 950 mA IF = 950 mA IF = 950 mA IF = 950 mA MIN. 34 2820 80 2970 80 3060 80 3200 80 3240 80 3240 80 TYP. (37) (3140) (0.4610) (0.4150) (2700) (83) (3300) (0.4370) (0.4030) (3000) (83) (3400) (0.4090) (0.3930) (3500) (83) (3550) (0.3820) (0.3800) (4000) (82) (3600) (0.3480) (0.3600) (5000) (82) (3600) (0.3190) (0.3390) (6000) (82) MAX. 40 - Unit V lm K lm K lm K lm K lm K lm K - (Note) Values inside parentheses are shown for reference purpose only. *5 (After 20 ms drive, Measurement tolerance: ± 3 %) *6 Monitored by Sharp's 8 inch integrating sphere and Otsuka electronics MCPD-LE3400 (After 20 ms drive, Measurement tolerance: ± 10 %) *7 Monitored by Sharp's 8 inch integrating sphere and Otsuka electronics MCPD-LE3400 (After 20 ms drive, Measurement tolerance: ± 0.005) *8 Monitored by Sharp's 8 inch integrating sphere and Otsuka electronics MCPD-LE3400 (After 20 ms drive, Measurement tolerance: ± 2) DG-127015B Model No. Page GW6DMD**NFC 5 of 18 3-3. Derating curve Forward Current Derating Curve 1400 Forward Current IF [mA] 1200 1000 800 600 400 200 0 -30 -20 -10 0 10 20 30 40 50 60 Case Temperature Tc [℃] 70 80 90 100 110 (Note) To keep the case temperature lower than the rating, enough heat-radiation performance needs to be secured by using an adequate heat sink. For soldering connection, please evaluate in your circumstance to make sure soldering reliability. ( Above derating curve is specified to LED device, not for soldering connection ) And please consider to avoid physical stress between wire and substrate, and some protection like silicon bond on top of soldered wire is recommended. Please ensure the maintenance of heat radiation not to exceed case temperature over the rating in operation. （Measuring point for case temperature） measuring point DG-127015B Model No. Page GW6DMD**NFC 6 of 18 4. Reliability 　　The reliability of products shall be satisfied with items listed below. 4-1. Test items and test conditions No. Test item Confidence level: 90 % Samples Defective LTPD n C (%) Test conditions 1 Temperature Cycle - 40 ℃(30 min) ～ + 100 ℃(30 min), 100 cycles 2 Temperature Humidity Storage High Temperature Storage Low Temperature Storage Steady State Operating Life Shock Tstg = + 60 ℃, RH = 90 %, Time = 1000 h 3 4 5 6 11 0 20 11 0 20 11 0 20 11 0 20 11 0 20 5 0 50 5 0 50 Tstg = + 100℃, Time = 1000 h Tstg = - 40 ℃, Time = 1000 h Tc = 90 ℃, IF = 950 mA, Time = 1000 h 2 Acceleration: 15000 m/s , Pulse width: 0.5 ms Direction: 3 directions (X, Y and Z) 3 trials in each direction 7 Vibration Frequency: 100 to 2000 Hz for 4 minutes per trial Acceleration: 200 m/s2 Direction: 3 directions (X, Y and Z) 4 trials in each direction 4-2. Failure criteria No. Parameter 1 Forward Voltage 2 Luminous Flux Symbol VF Ф Failure criteria VF ＞ Initial value × 1.1 Ф＜ Initial value × 0.7 DG-127015B Model No. Page GW6DMD**NFC 7 of 18 5. Quality level 5-1. Applied standard ISO2859-1 5-2. Sampling inspection A single normal sampling plan, level S-4. 5-3. Inspection items and defect criteria No. Item 1 No radiation No light emitting 2 3 4 Electro-optical characteristics External dimensions Appearance Defect criteria Classification AQL Major defect 0.1 Not conforming to the specification (Forward voltage, Luminous flux and Chromaticity) Not conforming to the specified dimensions (External dimensions of ① and ② shown in Page 2) Nonconformity observed in product appearance is determined as defective only when electro-optical characteristics is affected by. Minor defect ■Foreign material, scratch, or bubble at emitting area: 0.8 mm φ ■Fiber generation at emitting area: 0.2 mm in width and 2.5 mm in length ■Foreign material at connection terminal: 0.8 mm φ ■Substrate burr on edge: Over dimension tolerance (Note) Products with removable foreign material attached on is not determined to be defective. 0.4 DG-127015B Model No. Page GW6DMD**NFC 8 of 18 6. Supplements 6-1. Chromaticity rank table (Tolerance: x,y ± 0.005） （IF = 950 mA, Tj = 90 ℃） **： **： 27 Rank x y 1 Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.4600 0.4555 0.4620 0.4665 0.4200 0.4100 0.4100 0.4200 Chromaticity Diagram 0.430 0.420 y 1 0.410 0.400 2700K 2800K 2600K 0.390 0.440 0.450 0.460 x 0.470 0.480 DG-127015B Model No. Page GW6DMD**NFC 9 of 18 (Tolerance: x,y ± 0.005） （IF = 950 mA, Tj = 90 ℃） **： **： 30 Range x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.4360 0.4315 0.4380 0.4425 0.4080 0.3980 0.3980 0.4080 Chromaticity Diagram 0.425 y 0.415 0.405 1 0.395 3200K 3100K 3000K 2900K 2800K 0.385 0.415 0.425 0.435 x *--- : MacAdam Ellipse 3step from chromaticity center 0.445 0.455 DG-127015B Model No. Page GW6DMD**NFC 10 of 18 (Tolerance: x,y ± 0.005） （IF = 950 mA, Tj = 90 ℃） **： **： 35 Range x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.4080 0.4035 0.4100 0.4145 0.3980 0.3880 0.3880 0.3980 Chromaticity Diagram 0.410 0.400 y 1 0.390 0.380 3600K 3500K 3400K 3300K 0.370 0.390 0.400 0.410 x 0.420 0.430 DG-127015B Model No. Page GW6DMD**NFC 11 of 18 (Tolerance: x,y ± 0.005） （IF = 950 mA, Tj = 90 ℃） **： **： 40 Range x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.3810 0.3765 0.3830 0.3875 0.3850 0.3750 0.3750 0.3850 Chromaticity Diagram 0.400 y 0.390 0.380 1 0.370 3900K 4000K 4100K 0.360 0.360 0.370 0.380 x *--- : MacAdam Ellipse 3step from chromaticity center 0.390 0.400 DG-127015B Model No. Page GW6DMD**NFC 11 of 18 (Tolerance: x,y ± 0.005） （IF = 950 mA, Tj = 90 ℃） **： **： 50 Rank x y 1 Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.3475 0.3420 0.3485 0.3540 0.3650 0.3550 0.3550 0.3650 Chromaticity Diagram 0.380 y 0.370 1 0.360 0.350 4800K 5000K 0.340 0.330 0.340 0.350 x 0.360 0.370 DG-127015B Model No. Page GW6DMD**NFC 13 of 18 (Tolerance: x,y ± 0.005） （IF = 950 mA, Tj = 90 ℃） **： **： 60 Range x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.3185 0.3130 0.3195 0.3250 0.3440 0.3340 0.3340 0.3440 Chromaticity Diagram 0.360 5600K 6000K 5800K 6200K 0.350 y 6400K 0.340 1 0.330 0.320 0.300 0.310 0.320 x 0.330 0.340 DG-127015B Model No. Page GW6DMD**NFC 14 of 18 6-2. Packing ■ One tray composed of 40 pieces ■ 5 trays (200 piecies) and one upper lid-tray in one moisture-proof bag ■ 2 bags (400 pieces) in one carton ■ Dimensions of outer carton: 235 × 220 × 90 mm (Reference value) (Note 1) There are cases of one carton composed of one bag. (200 pieces) (Note 2) State of packing is subject to change. ＜Outer carton＞ ＜One bag＞ 200 pieces × 2 bags = 400 pieces ＜One tray＞ 　40 pieces × 5 trays = 200 pieces 5 × 8 ＝ 40 pieces (225mm) 6-3. Label Following label is attached on moisture-proof bags. SHIPMENT TABLE PART No. GW6DMD**NFC (GW6DMD**NFCX) QUANTITY. 200 LOT No. RANK 1 XX22G01001A CORPORATION MADE IN XXXXXXXXXX SHARP SHARP LABEL R.C ←Model number ←(Model number + suffix code) ←Quantity and rank ←Lot No. ←Bar code ←Production country ・MADE IN PHILIPPINES ・MADE IN INDONESIA (210mm) 1) Lot No. indication X X 2 2 G 0 1 0 0 1 A ① ②③④ ⑤ ⑥ ⑦ ① Production plant code(PHL(MAT):50,IDN(SSI):00) ② Shipping year（Year last digit） ③ Shipping month （1～9 or O, N, D） ④ Fixed code G ⑤ Shipping date（01～31） ⑥ Serial No. ⑦ Backup code A 6-4. Indication printed on product 　 Model No. and control No. are indicated on substrate surface. 1) Model No. Abbreviated Model No. " 6DMD**NFC " is indicated. 2) Control No. Indicated as follows; X 1 2 B 0 1 ‐ 1 ① ② ③ ④ ⑤ ① Production plant code (to be indicated alphabetically) PHL（MAT)：M、　IDN（SSI)：Y Model No. ② Year of production (the last two figures of the year) ③ Month of production 　(to be indicated alphabetically with January corresponding to A) ④ Date of production (01～31) ⑤ Rank: Chromaticity rank is indicated as follows; Rank 1 → 1 Control No. DG-127015B Model No. Page GW6DMD**NFC 15 of 18 7. Precautions ① Storage conditions Please follow the conditions below. ・Before opened: Temperature 5 ～ 30 ℃, Relative humidity less than 60 %. (Before opened LED should be used within a year) ・After opened: Temperature 5 ～ 30 ℃, Relative humidity less than 60 %. (Please apply soldering within 1 week) ・After opened LED should be kept in an aluminum moisture proof bag with a moisture absorbent material (silica gel). ・Avoid exposing to air with corrosive gas. If exposed, electrode surface would be damaged, which may affect soldering. ② Usage conditions This product is not designed for the use under any of the following conditions. Please confirm performance and reliability well enough if you use under any of the following conditions; ・In a place with a lot of moisture, dew condensation, briny air, and corrosive gas. (Cl, H2S, NH3, SO2, NOX, etc.) ・Under the direct sunlight, outdoor exposure, and in a dusty place. ・In water, oil, medical fluid, and organic solvent. ・Please do not use component parts contain sulfur (gasket packing, adhesive material, etc.). ③ Heat radiation If forward current (IF) is applied to single-state module at any current, there is a risk of damaging LED or emitting smoke. Equip with specified heat radiator, and avoid heat stuffed inside the module. ④ Installation Material of board is alumina ceramic. If installed inappropriately, trouble of no radiation may occur due to board crack or overheat. Please take particular notice for installation. Refer to the following cautions on installation. ・ Apply thermolysis adhesive, adhesive sheet or peculiar connector when mounted on heat radiator. In case of applying adhesive or adhesive sheet only, check the effectiveness and reliability before fixing. If LED comes off from heat radiator, unusual temperature rise entails hazardous phenomena including device deterioration, coming off of solder at leads, and emitting smoke. ・ When LED device is mechanically fixed or locked, Please take into consideration regarding the method of attachment due to fail from stress. ・ Avoid convexly uneven boards. Convex board is subject to substrate cracking or debasement of heat release. ・ It is recommended to apply adhesive or adhesive sheet with high thermal conductivity for radiation of heat effectively. ・ Please take care about the influence of color change of adhesive or adhesive sheet in initial and long term period, which may affect light output or color due to change of reflectance from backside. DG-127015B Model No. Page GW6DMD**NFC 16 of 18 ・ Do not touch resin part including white resin part on the surface of LED. No light emission may occur due to damage of resin or cutting wire of LEDs by outer force. When using tweezers, please handle by ceramic substrate part and avoid touching resin part. For mounting, please handle by side part of ceramic or the specified area shown below. Handling area ⑤ Connecting method In case of solder connecting method, follow the conditions mentioned below. ・Use Soldering iron with thermo controller (tip temperature 380 ℃), within 5 seconds per one place. ・Secure the solderwettability on whole solder pad and leads. ・During the soldering process, put the ceramic board on materials whose conductivity is poor enough not to radiate heat of soldering. ・Warm up (with using a heated plate) the substrate is recommended before soldering. ( preheat condition: 100 ℃ ～ 150 ℃, within 60 sec ) ・Avoid touching a part of resin with soldering iron. ・This product is not designed for reflow and flow soldering. ・Avoid such lead arrangement as applying stress to solder-applied area. ・Please do not detach solder and make re-solder. ・Please solder evenly on each electrodes. ・Please prevent flux from touching to resin. ⑥ Static electricity This product is subject to static electricity, so take measures to cope with it. Install circuit protection device to drive circuit, if necessary. ⑦ Drive method ・Any reverse voltage cannot be applied to LEDs when they are in operation or not. Design a circuit so that any flow of reverse or forward voltage can not be applied to LEDs when they are out of operation. ・Module is composed of LEDs connected in both series and parallel. Constant voltage power supply runs off more than specified current amount due to lowered VF caused by temperature rise. Constant current power supply is recommended to drive. ⑧ Cleaning Avoid cleaning, since silicone resin is eroded by cleaning. ⑨ Color-tone variation Chromaticity of this product is monitored by integrating sphere right after the operation. Chromaticity varies depending on measuring method, light spread condition, or ambient temperature. Please verify your actual conditions before use. DG-127015B Model No. Page GW6DMD**NFC 17 of 18 ⑩ Safety ･Please prevent to see lighting LED devices directly at any moment for safety your eyes. ･Looking light from LEDs for a long time may result in hurt your eyes. ･In case that excess current (over ratings) are supplied to the device, hazardous phenomena including abnormal heat generation, emitting smoke, or catching fire can be caused. Take appropriate measures to excess current and voltage. ・In case of solder connecting method, there is a possibility of fatigue failure by heat. Please fix the leads in such case to protect from short circuit or leakage of electricity caused by contact. ・Please confirm the safety standards or regulations of application devices. ・Please careful not to injure your hand by edge of ceramic substrate. ⑪ Other cautions Guarantee covers the compliance to the quality standards mentioned in the Specifications, however it does not cover the compatibility with application of the end-use, including assembly and usage environment. In case any quality problems occurred in the application of end-use, details will be separately discussed and determined between the parties hereto. DG-127015B Model No. Page GW6DMD**NFC 18 of 18 8. Characteristics diagram (TYP.) Forward Voltage vs. Forward Current Forward Current vs. Relative Luminous Flux Tj = 90℃ 1400 120 1200 Forward Current IF [mA] Relative Luminous Flux [%] Tj = 90℃ 140 100 80 60 40 20 1000 800 600 400 200 0 0 0 200 400 600 800 1000 1200 29 1400 31 Forward Current IF [mA] 33 35 37 Case Temperature vs. Relative Luminous Flux 41 Case Temperature vs. Forward Voltage IF = 950 mA 120 42 100 40 Forward Voltage VF [V] Relative Luminous Flux [%] 39 Forward Voltage VF [V] 80 60 40 20 IF = 950mA 38 36 34 32 0 0 20 40 60 Case Temperature Tc [℃] 80 100 0 20 40 60 Case Temperature Tc [℃] (Note) Characteristics data shown here are for reference purpose only. (Not guaranteed data) 80 100