LQ080Y5DZ03A

20 pages LCY-12058A-1 NOTICE This publication is the proprietary of Sharp Corporation (hereinafter referred to as SHARP) and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. The application circuit examples in this publication are provided to explain the representative applications of SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP's device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for use in general electronic equipment designs , such as: ・Car Navigation system ・Automotive auxiliary information display ・Automotive audio visual equipment The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: ・Transportation control and safety equipment (i.e. aircraft, trains, automobiles, etc.) ・Traffic signals ・Gas leakage sensor breakers ・Alarm equipment ・Various safety devices etc. SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: ・Military and space applications ・Nuclear power control equipment ・Medical equipment for life support Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific" applications other than those recommended by SHARP. Contact and consult with a SHARP representative if there are any questions about the contents of this publication. LCY-12058A-2 １．General １．General This TFT-LCD module is a color active matrix LCD (Liquid Crystal Display) module of transmissive type incorporating amorphous silicon TFT (Thin Film Transistor). General specification of the module is shown in the Table 3-1. It is composed of a color TFT-LCD panel, driver ICs, control-PWB, FPC, frame, shielding front case, shielding back case and backlight unit. ２．Features ２．Features ・Utilizes a panel with a 15:9 aspect ratio, which makes the module suitable for use in wide-screen systems. ・The 8.0 inch screen produces a high resolution image that is composed of 384,000 pixels elements in a stripe arrangement. ・Graphics and texts can be displayed on a 800×RGB×480 dots panel with 262,144 colors by supplying 18 bits (6 bits×RBG) data signal. ・Wide viewing field angle technology is employed. ・By adopting an active matrix drive, a picture with high contrast is realized. ・Reduced reflection as a result of low reflection black matrix and an antiglare (AG) and antireflection (AR) polarizer being adopted. The reflectance is 1.5% Typical. ・By COG method, realized a slim, lightweight, and compact module. ・Realized a high quality picture of the natural color appearance by adopting Normally Black Mode which is superior to the color appearance. ・An inverted video display in the vertical and horizontal directions is possible. ・The backlight is excellent of brightness rising characteristics at low temperature in consideration of automotive application. ・Minimized image flicker artifacts by implementing checker pattern dot inversion driving scheme 3. Mechanical specifications (Dot Composition) General Specification of the Module Parameter Display format Active area Screen size (Diagonal) Dot pitch Pixel configuration Outline dimension Mass Table 3-1 Specifications 384,000 800(RGB)W×480H 174.0（W）×104.4（H） 20.3 [ 8.0 “ ] 0.0725（W）×0.2175（H） R,G,B Stripe configuration 191.8 (W)×120.0 (H)×13.5(D) 400（Typ.) [Note 3-1] Excluding protrusions. Typical values are given. For detailed measurements and tolerances, please refer to Fig. 1. Units pixels dots mm cm mm mm ｇ Remarks [Note 3-1] LCY-12058A-3 4. Input terminal and and its function 4-1 TFT-LCD panel driving part : Connector used ： FH41-68S-0.5SH(05) (HRS) Table 4-1 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Symbol TEST GND GND GND GND GND N.C. B+ B+ B+ B+ B+ N.C. GND GND GND GND GND GND BL_PWM N.C. THM1 THM2 GND VRV HRV GND N.C. VCC VCC VCC N.C. GND R5 R4 R3 R2 R1 R0 GND G5 G4 G3 G2 G1 G0 GND Description Continuity to pin 68 GND for circuit GND for circuit GND for circuit GND for circuit GND for circuit OPEN POWER for LED circuit POWER for LED circuit POWER for LED circuit POWER for LED circuit POWER for LED circuit OPEN GND for circuit GND for circuit GND for circuit GND for circuit GND for circuit GND for circuit PWM control for LED driver OPEN Thermistor Thermistor GND for circuit Turning the direction of vertical scanning Turning the direction of horizontal scanning GND for circuit OPEN Logical Power Supply (+3.3V power supply) Logical Power Supply (+3.3V power supply) Logical Power Supply (+3.3V power supply) OPEN GND for circuit RED data signal (MSB) RED data signal RED data signal RED data signal RED data signal RED data signal (LSB) GND for circuit GREEN data signal (MSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal (LSB) GND for circuit Remarks [Note4-5] [Note4-5] [Note4-4] [Note4-3] LCY-12058A-4 Pin No. Symbol 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 B5 B4 B3 B2 B1 B0 GND PON GND GND NCLK GND GND VD DEN HD GND GND GND GND TEST Description BLUE data signal (MSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal (LSB) GND for circuit Display reset signal GND for circuit GND for circuit Clock signal for sampling each data signal GND for circuit GND for circuit Vertical sync Horizontal Data Enable Horizontal sync GND for circuit GND for circuit GND for circuit GND for circuit Continuity to pin 1 Remarks [Note4-1] [Note4-2] [Note4-1] [Note4-1] Hsync Vsync Negative polarity Negative polarity [Note4-2] The horizontal display starting position is settled in accordance with a rising timing of DEN signal. (Refer to Fig.2) In case DEN is fixed to “Low”, the horizontal display starting position is determined as described in Fig.2.(Don’t keep DataEn “High” during operation.) [Note4-3] HRV="Hi" : Regular video HRV="Lo" : Horizontally inverted video [Note4-4] VRV="Hi" : Regular video VRV="Lo" : Vertically inverted video [Note4-5] Thermistor parts number : NSM2103F344F3 (OHIZUMI) LCY-12058A-5 5. Absolute maximum ratings Table 5-1 Parameter Input voltage for back light +3.3V power supply Input signal voltage 1 Input signal voltage 2 Storage temperature Operating temperature （LCD panel surface） Operating temperature （ Ambient temperature ） Symbol VB+ ＭＩＮ -0.3 ＭＡＸ 23.0 Ｖcc Vi1 Vi2 Ｔstg Ｔopr1 -0.3 -0.3 -0.3 -40 -30 +4.6 Vcc+0.3 "VB+" +0.3 95 85 Ｔopr2 -40 85 GND=0V Note Unit V 21V～23V Max 1s V V [Note5-1] V [Note5-2] ℃ [Note5-3,4] ℃ [Note5-3,4,5,6] ℃ [Note5-6] [Note5-1] HD , DEN , VD , NCLK , B0～B5 , G0～G5 , R0～R5 , HRV , VRV , PON [Note5-2] BL_PWM [Note5-3] This rating applies to all parts of the module and should not be exceeded. The specified temperature provides the maximum value within 5mm around the module. [Note5-4] Maximum wet-bulb temperature is to be less than 58℃. Condensation of dew must be avoided as electrical current leaks will occur, causing a degradation of performance specifications. [Note5-5] The operating temperature only guarantees operation of the circuit. Specifications (contrast ratio, response time and other factors related to display quality) are determining at ambient temperature (Ta=25℃) . [Note5-6] Ambient temperature when the backlight is lit. (by PWM). PWM dimming shall operate at Ta≧+75℃. (See attached below figure) （Thermistor value shall be controlled more than 1.3KΩ） The display reduce performance level between -40℃ ≦ Ta ≦ -30℃ and +75℃ ≦ Ta ≦ +85℃ For reference when being with a Touch Panel, PWM dimming shall operate at Ta≧+70℃. （Thermistor value shall be controlled more than 1.35KΩ） Countermeasures for heat generation from LCD module such as heat sink are mandatory at customer’s system. 110 PWM Dimming Duty Cycle(%) 100 90 80 Without TP 70 60 50 40 With TP 30 20 10 0 50 [Note5-7] 60 70 ambient temperature(℃) The above graph is reference data as LCD module 80 90 LCY-12058A-6 6. Electrical Electrical characteristics 6-1 TFT-LCD panel driving section Table 6-1 Parameter Symbol Supply voltage VB+ B＋ Current dissipation VB+ Input Low voltage VIBL Input High voltage VIBH VCC Supply voltage Vcc Current dissipation Icc Permissive input ripple VRF Input Low voltage VIL Input High voltage VIH Negative trigger voltage VNT Positive trigger voltage VPT Hysteresis voltage VHYS Input current 1 (Low) IIL1 Input current 1 (High) IIH1 Input current 2(Low) IIL2 Input current 2 (High) IIH2 Input current 3 (Low) IIL3 Input current 3 (High) IIH3 Input current 4 (Low) IIL4 Input current 4 (High) IIH4 Input current 5 (Low) IIL5 Input current 5 (High) IIH5 ＭＩＮ 7.0 － GND 2.1 +3.0 － － GND 0.7VCC 0.8 1.4 0.3 － － 30 － － 30 － － － － ＴＹＰ 13.5 450 － － +3.3 260 － － － － － － － － － － － － － － － ＭＡＸ 18.0 1000 0.4 5.5 +3.6 350 100 0.3VCC VCC 1.6 2.4 1.5 2.0 2.0 200 2.0 2.0 200 600 2.0 1.0 600 Ta= 25℃ Unit Remarks V [Note6-1] mＡ Max:VB+=7V V “BL_PWM”terminal Ｖ V [Note6-1] mA [Note6-2] mVpp V Ｖ [Note6-3] Ｖ “PON” terminal V V μA VI=0V or VCC μA [Note 6-4] μA VI=0V or VCC μA “HD,VD” terminal μA VI=0V or VCC μA “DEN” terminal μA VI=0V or VCC μA “HRV,VRV” terminal μA VIB=0V or 5.5V μA “BL_PWM” terminal [Note6-1] On-off conditions for supply voltage 0 < t1 0 < t2 ≦ 10ms 0 < t3 ≦ 1s t4 ≧ 1s 0 < t5 ≦ 10ms t6 ≦ 10ms 0ms ≦ t7 PON VB+ VB+ Vcc 3.0V data 7.0V 3.0V 0.3Vcc t6 7.0V t7 t2 0.3V t4 t2 t1 t3 *When PON signal turns off, display pattern may be un-controlled for an instant. [Note6-2] Typical current situation: White (GS63) pattern Timing: Typical VCC= +3.3 V [Note 6-3] HD , DEN , VD , NCLK , B0～B5 , G0～G5 , R0～R5 , HRV , VRV [Note 6-4] NCLK , B0～B5 , G0～G5 , R0～R5 , PON data 0.3Vcc 0.3V t3 PON t5 LCY-12058A-7 7. Timing Characteristics of input signals 7-1) Timing characteristics Table 7-1 Parameter Symbol Clock Frequency fCLK [NCLK] Hi_Time tWCH Lo_Time tWCL Data Setup time tDS [I* 0-5] Hold time tDH Horizontal Cycle tH(t) sync.signal tH(clk) [HD] Pulse width tHPW Vertical sync. Cycle tV Signal [VD] Pulse width tVPW Frame rate fV Horizontal display period tHA HD_NCLK phase difference tHC HD_VD phase difference tVH Vertical front porch tVFP Vertical back porch tVBP Vertical display period tVA Enable signal Setup time tES [HENAB] Hold time the Pulse width tEP Horizontal front porch Horizontal back porch tHFP tHBP PWM Dimming Frequency PWM Dimming Duty Cycle fpwm Min. 31.95 5 5 5 5 31.45 1024 5 520 2 50 A-8 -10 5 5 5 Typ. 33.26 ― ― ― ― 31.75 1056 ― 525 ― 60 800 A 0 ― 35 480 ― ― Max. 34.60 ― ― ― ― 32.05 1088 THb－5 530 TV-2 60 A+8 10 ― ― ― 800 2 ― ck ― 194 20 150 1.0 ― ― ― Unit MHz ns ns ns ns µs ck ck line line Hz ck ns ck line line line ns ns only 800ck A=Tc/2 （Tc=1/fCLK） only 35 line only 480 line [Note 7-1] [Note 7-1] only 800ck ck ck 222 250 100 Ta= 25℃ Note ck Hz % [Note 7-2] only 194ck [Note 7-3] BL_PWM [Note 7-1] Enable signal must be input into Vertical invalid data period as well as Vertical display period. [Note 7-2] This spec is applied for DEN Low fix mode. [Note 7-3] This spec is applied for DEN active mode. LCY-12058A-8 7-2) Input Data Signals and Display Position on the screen Refer to the following figure ＵＰ D1,DH1 D2,DH1 D1,DH2 D2,DH2 D800,DH1 D3,DH1 D1,DH3 R G B D800,DH480 D1,DH480 Display position of input data (H,V) LCY-12058A-9 8. Input Signals, Basic Display Color and Gray Scale Scale of Each Color Table 8-1 Colors & Data signal Gray scale Gray Scale R0 0 :Low level voltage 1 :High level voltage R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 Basic color Gray Scale of red Gray Scale of green Gray Scale of bleu Black － 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue － 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Green － 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Cyan － 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 Red － 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Magenta － 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Yellow － 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 White － 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
         Brighter GS61 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0  GS62 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Red GS63 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GS1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0
         Brighter GS61 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0  GS62 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 Green GS63 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GS1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
         Brighter GS61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1  GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 Bleu GS63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Each basic color can be displayed in 64 gray scales by 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen. LCY-12058A-10 9. Optical characteristics Ta=25℃ , Vcc=+3.3V , VB+=13.5V , BL_PWM=100% ,Initial Value Table 9-1 Parameter Viewing Angle Range Contrast ratio Rise Response Fall time Color Chromaticity Luminance Off-Axis Half Brightness Uniformity LED +25℃ lifetime Symbol Condition θ21,θ22 CR≧10 θ11,θ12 CRmax θ=0° τr τd x (white) y (white) x (red) y (red) x (green) y (green) x (blue) y (blue) Y θ21,θ22 θ11,θ12 u - continuation Min 70 70 1100 0.255 0.280 0.590 0.320 0.290 0.590 0.120 0.060 450 35 20 - Typ 85 85 2000 15 5 0.290 0.320 0.620 0.350 0.320 0.620 0.150 0.090 645 45 30 85 Max 35 15 0.330 0.360 0.650 0.380 0.350 0.650 0.180 0.120 - Unit degree degree Remarks cd/ ㎡ degree degree % 【Note 9-1】 10,000 - - hour 【Note 9-4】 【Note 9-1,2】 【Note 9-2】 ms ms 【Note 9-3】 【 Note 9-6】 ±0.03 NTSC ratio is Typ64%. 【Note 9-5】 ※Above specification warrants only initial condition. ※Measured after 30 minutes operation. The optical characteristic is measured by using the method of fig.6 and fig.7 under the condition of the darkroom or equivalent to it. Photo detector（SR-UL1） Photo detector（EZ-CONTRAST） 400mm Field=1° Center of the screen(θ=０°） Center of the screen(θ=０°) TFT-LCD module TFT-LCD module Fig. 6 The way of measuring Viewing angle range/ Response time Fig. 7 The way of measuring Luminance/ Chromaticity/ Contrast LCY-12058A-11 [Note9-1] Viewing angle range is defined as follows. Normal line θ22 θ11 θ12 θ21 6 o’clock direction [Note9-2] Contrast ratio of transmission is defined as follows: Photo detector output with LCD being "white" Contrast ratio (CR)= Photo detector output with LCD being "black" [Note9-3] Response time is obtained by measuring the transition time of photo detector output, when input signals are applied so as to make the area "black" to and from "white". White Black White 100% 90% Photo detector output 10% 0% ) t i n u y r a r t i b r a ( τｄ τｒ Time [Note9-4] LED life time is defined as the time when the brightness of the panel is not become less than 50% of the original value in the continuous operation under the condition of LED current If= 70 mArms and PWM dimming 100%~5% (Ta=25℃). LCY-12058A-12 [Note9-5] u= =Ymin/Ｙmax:( 9points luminance) H×2/10 H×3/10 H×3/10 H×2/10 V×2/10 V×3/10 V V×3/10 V×2/10 H [Note 9-6] The tolerance of color chromaticity of white is shown as follows The tolerance of color chromaticity of white 0.370 0.360 0.350 0.340 0.330 0.320 0.310 0.300 TYP 0.290 tYP±0.04 0.280 0.270 0.240 The tolerance of color chromaticity of white 0.250 0.260 0.270 0.280 0.290 0.300 0.310 0.320 0.330 0.340 LCY-12058A-13 10. 10. Display quality The display quality of the module shall be in compliance with the Incoming Inspection Standards. Please reference document number LDI-080DZ03. 11. Mechanical characteristics 11-1 External appearance No extreme defect exists. (See Fig. 1) 11-2 LCD Panel toughness The LCD panel shall not be broken ,when 19N is pressed on the center of the panel by a smooth sphere having 15 mm diameter. Caution: In spite of very soft toughness, if, in the long-term, add pressure on the active area, it is possible to occur the functional damage. 12. 12. Handling instructions 12-1 Mounting of module The TFT-LCD module is designed to be mounted on equipment using the mounting tabs in the four corners of the module at the rear side. On mounting the module, as the 2.5 tapping screw (fastening torque is TYP 0.3N・m(design target)) is recommended, be sure to fix the module on the same plane, taking care not to wrap or twist the module. Don't reach the pressure of touch-switches of the set side to a module directly, because images may be disturbed. Power off the module when you connect the input/output connector. Please ensure that the LCD metal case is grounded in the system design. 12-2 Precautions in mounting Polarizer which is made of soft material and susceptible to flaw must be handled carefully. Protection sheet is applied on the surface to protect it against scratches and dirties. It is recommended to remove the protection sheet immediately before the use, taking care of static electricity. Precautions in removing the protection sheet A) Working environment When the protection sheet is removed off, static electricity may cause dust to stick to the polarizer surface. To avoid this, the following working environment is desirable. a) Floor: Conductive treatment of 1MΩ or more on the tile (conductive mat or conductive paint on the tile) b) Clean room free form dust and with an adhesive mat on the doorway c) Advisable humidity:50%～70% Advisable temperature:15℃～27℃ d) Workers shall wear conductive shoes, conductive work clothes, conductive gloves and an earth band. LCY-12058A-14 B) Working procedures a) Direct the wind of discharging blower somewhat downward to ensure that module is blown sufficiently. Keep the distance between module and discharging blower within 20 cm. b) Attach adhesive tape to the protection sheet part near discharging blower so as to protect polarizer against flaw. c) Remove the protection sheet, pulling adhesive tape slowly to your side. d) On removing the protection sheet, pass the module to the next work process to prevent the module to get dust. Direction of wind of blower discharging blower less than 20cm module Adhesive tape e) Method of removing dust from polarizer ･ Blow off dust with N2 blower for which static electricity preventive measure has been taken. ･ Since polarizer is vulnerable, wiping should be avoided. But when the panel has stain or grease, to use adhesive tape is recommended to remove them softly from the panel. When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with soft dry cloth. For stubborn dirties, wipe the part, breathing on it. Wipe off water drop or finger grease immediately. Long contact with water may cause discoloration or spots. TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped on hard surface. Handle with care. Since CMOS LSI is used in this module, take care of static electricity and earth your body when handling. 12-3 Caution of product design Please follow the below items strictly when the product is designed by using this module. ・ The LCD module shall be protected against water or salt-water by the waterproof cover. ・ Please take measures to interferential radiation from the module not to interfere surrounding appliances. ・ Because driving voltage for backlight is high, it is dangerous to use LCD module under the conditions which are deviated from specification. ・ The equipment for which the LCD module is used shall have fail-safe design so that the safety can be ensured in case abnormality of inverter circuit, etc. should occur. 12-5) Others 1. Liquid crystal is sensitive to ultraviolet rays. Do not expose the module to direct sunlight for a long time. 2. Storage of the module under temperatures lower than the specified range may solidify liquid crystal in the module, resulting in damage to the panel. Storage of the module under temperatures exceeding the specified range may cause an irreversible change of liquid crystal to the isotropic phase. 3. When the LCD is broken, take care not to mouth liquid crystal. When liquid crystal adheres to skin or clothes, wash it off immediately with soap and water. 4. Remove any water droplets or dirt on the polarizer without delay. Failure to do so may cause degradation. 5. Observe all other precautionary requirements in handling general electronic components. 6. When it keeps pushing a part of the touch panel for a long time, it causes the generation of Newton rings. 7.The LCD has been calibrated prior to shipment, do not change any of the adjustable values within the LCD module. LCY-12058A-15 13. 13. Packing form 13-1 The packing form figure : See Fig.3 13-2 a)Piling number of cartons : Max 8 b)Conditions for storage Environment ①Temperature : 0～40℃ ②Humidity : 60%RH or less (at 40℃) No dew condensation at low temperature and high humidity. ③Atmosphere : Harmful gas, such as acid or alkali which bites electronic components and/or wires, must not be detected. ④Period : about 3 months ⑤Opening of the package : In order to prevent the LCD module from breakdown by electrostatic charges, please control the room humidity over 50%RH and open the package taking sufficient countermeasures against electrostatic charges, such as earth, etc. 14.Others 14.Others 14-1)Indication of lot number ①
Attached location of the label ②
Indicated contents of the label : See Fig.1 (Outline Dimensions). LQ080Y5DZ03A LQ080Y5DZ03A model No. lot No. Contents of model No. Contents of lot No. the 1st ～11th figure・・model No. the 12th ・・ management division the 1st figure ‥ production year (ex. 2011 → 1) the 2nd figure ‥ production month 1,2,3,‥‥‥,9,X,Y,Z the 3rd～8th figure ‥ serial No. 000001～ the 9th figure ‥ revision marks space,A,B,C‥ 14-2)Pb-free Environmental burden status This TFT-LCB module is chromium hexavalent-free and Pb-free LCY-12058A-17 1 8 1 9 LCY-12058A-20