PR36MF22NSZ

PR36MF22NSZ/PR39MF22NSZ PR36MF22NSZ/ PR39MF22NSZ I Features 1. Compact 8-pin dual-in-line package type. 2. RMS ON-state current IT(rms):0.6A, 0.9A 3. Built-in zero-cross circuit. 4. High repetitive peak OFF-state voltage. (VDRM:MIN. 600V) 5. Isolation voltage between input and output. (Viso(rms):4kV) 6. Under preparation for UL and CSA. 8-Pin DIP Type SSR for Low Power Control I Outline Dimensions 2.54 8 A 6 ±0.25 (Unit : mm) 5 A (Model No.) Anode mark 1 2 3 ±0.5 4 1.2±0.3 7.62±0.3 0.5TYP. 3.5±0.5 9.66 I Applications I Model Line-up RMS ON-state current (rms) 0.6A 0.9A Model No. PR36MF22NSZ PR39MF22NSZ (Ta=25°C) Unit mA V A A V kV °C °C °C 8 2.9±0.5 1. Various types of home appliances 3.25±0.5 0.5±0.1 6.5±0.5 0.26±0.1 θ:0 to 13˚ θ Internal connection Diagram I Absolute Maximum Ratings Parameter Symbol Forward current IF Reverse voltage VR *1 RMS ON-state PR36MF22NSZ IT (rms) current PR39MF22NSZ *2 Peak one cycle PR36MF22NSZ Isurge surge current PR39MF22NSZ *1 6 5 Output Rating 50 6 0.6 0.9 6 9 600 4.0 −30 to +85 −40 to +125 260 (For 10s) Input Zero-cross circuit 1 1 2 3 4 2 3 4 5 6 8 Cathode Anode Cathode Cathode G T1 T2 Repetitive peak OFF-state voltage *3 VDRM Viso (rms) Topr Tstg Tsol Isolation voltage Operating temperature Storage temperature Soldering temperature Terminal 1 , 3 and 4 are common ones of cathode.To radiate the heat, solder all of the lead pins on the pattern of PWB. *1 The derating factors of absolute maximum ratings due to ambient temperature are shown in Fig.1, 2 *2 50Hz sine wave *3 AC for 1 min, 40 to 60%RH, f=60Hz Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://sharp-world.com/ecg/ PR36MF22NSZ/PR39MF22NSZ I Electrical Characteristics Input Symbol Parameter VF Forward voltage Reverse current IR Repetitive peak OFF-state current IDRM PR36MF22NSZ ON-state voltage VT PR39MF22NSZ Holding current IH Critical rate of rise of OFF-state voltage dV/dt Zero-cross voltage VOX IFT Minimum trigger current Isolation resistance RISO Turn-on time ton Conditions IF=20mA VR=3V VD=VDRM IT=0.6A IT=0.9A VD=6V − VD=1/√2 • VDRM IF=10mA, R load VD=6V, RL=100Ω DC=500V, 40 to 60%RHF VD=6V, RL=100Ω, IF=10mA MIN. − − − − − 100 − − 5×1010 − TYP. 1.2 − − − − − − − 1011 − MAX. 1.4 10 100 3.0 25 − 35 5 − 50 (Ta=25˚C) Unit V µA µA V mA V/µs V mA Ω µs Output Transfer characteristics Fig.1 RMS ON-state Current vs. Ambient Temperature 0.7 0.6 PR36MF22NSZ Fig.2 RMS ON-state Current vs. Ambient Temperature 1 PR39MF22NSZ RMS ON-state current IT (rms) (A) RMS ON-state current IT (rms) (A) 10 20 30 40 50 60 70 80 90 100 Ambient temperature Ta (˚C) 0.8 0.5 0.4 0.3 0.2 0.1 0 −30 −20 −10 0 0.6 0.4 0.2 0 −30 −20 −10 0 10 20 30 40 50 60 70 80 90 100 Ambient temperature Ta (˚C) Fig.3 Forward Current vs. Ambient Temperature 70 60 Forward current IF (mA) 50 40 30 20 10 0 −30 −20 −10 0 10 20 30 40 50 60 70 80 90 100 Ambient temperature Ta (˚C) NOTICE q The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: - - - Personal computers - -- Office automation equipment - -- Telecommunication equipment [terminal] - - - Test and measurement equipment - - - Industrial control - -- Audio visual equipment - -- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: - -- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) - - - Traffic signals - - - Gas leakage sensor breakers - - - Alarm equipment - -- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: - - - Space applications - -- Telecommunication equipment [trunk lines] - -- Nuclear power control equipment - -- Medical and other life support equipment (e.g., scuba). q q q Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. Contact and consult with a SHARP representative if there are any questions about the contents of this publication. q q q