PR3BMF51NSLF Series
PR3BMF51NSLF
Series
IT(rms)≦1.2A, Non-Zero Cross type
DIP 8pin
Triac output SSD
■Agency approvals/Compliance
■Description
1. Approved by UL508 file No.E94758
(as model No.R3BMF5)
2. Approved by CSA file No.063705
(as model No.R3BMF5)
3. Optionary approved by VDE
(DIN EN 60747-5-5), file No.40008898
(as model No.R3BMF5)
4. Package resin : UL flammability grade (94V-0)
PR3BMF51NSLF Solid State Device (SSD) is an
integration of an infrared emitting diode (IRED),
a Phototriac Detector and a main output Triac. This
device is ideally suited for controlling high voltage
AC loads with solid state reliability while providing
4kV isolation (Viso(rms)) from input to output.
■Applications
■Features
20 sleeves *Maximum
Output current,
IT(rms)≤1.2A
(51. lines×4
stairs)
1. Isolated interface between high voltage AC devices
and lower voltage DC control circuitry.
2. Switching motors, fans, heaters, solenoids, and
valves.
3. Phase or power control in applications such as
lighting and temperature control equipment.
2. Non-zero crossing functionary
3. 8 pin DIP package (SMT gullwing also available)
4. High repetitive peak off-state voltage (VDRM : 600V)
5. Superior noise immunity (dV/dt : MIN. 100V/μs)
6. Response time, ton : MAX. 100μs
7. High isolation voltage between input and output
(Viso(rms) : 4kV)
8. RoHS directive compliant
Notice
The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
Sheet No.: OP14009EN
Date: July. 2015
© SHARP Corporation
1
PR3BMF51NSLF Series
■Pin-Number and internal connection diagram
①
⑧
②
③
⑥
④
⑤
①
②
③
④
: Cathode
: Anode
: Cathode
: Cathode
⑤ : Gate
⑥ : T1
⑧ : T2
■Outline Dimensions
(Unit : mm)
Business dealing name
identification mark
Business dealing name
identification mark
(3digit)
(3digit)
Under Development
Under Development
Business dealing name
identification mark
Business dealing name
identification mark
(3digit)
(3digit)
Plating material : SnCu (Cu : TYP.2%)
Sheet No.: OP14009EN
2
PR3BMF51NSLF Series
Date code (3 digit)
2nd digit
Month of production
Month
Mark
January
1
February
2
March
3
April
4
May
5
June
6
July
7
August
8
September
9
October
O
November
N
December
D
Mark
P
R
S
T
U
V
W
X
A
B
C
…
…
A.D.
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
1st digit
Year of production
Mark
A.D.
A
2022
B
2023
C
2024
D
2025
E
2026
F
2027
H
2028
J
2029
K
2030
L
2031
M
2032
N
Day
1
2
3
4
5
6
7
8
9
10
11
12
3rd digit
Day of production
Mark
Day
Mark
Day
1
13
D
25
2
14
E
26
3
15
F
27
4
16
G
28
5
17
H
29
6
18
J
30
7
19
K
31
8
20
L
9
21
N
A
22
O
B
23
P
C
24
R
-
Mark
S
T
U
V
X
Y
Z
-
repeats in a 20 year cycle
Factory identification mark
Factory identification Mark
Country of origin
China
* This factory marking is for identification purpose only.
Please contact the local SHARP sales representative to see the actural
status of the production.
Sheet No.: OP14009EN
3
PR3BMF51NSLF Series
■Absolute maximum ratings
Rating
Forward current
IF
50 *3
mA
Reverse voltage
VR
6
V
RMS on-state current
IT(rms)
1.2 *3
A
Peak one cycle surge current
Isurge
12 *4
Repetitive peak off-state voltage
VDRM
600
A
V
Viso(rms)
4.0
kV
Operating temperature
Topr
-30 to +85
°C
Storage temperature
Tstg
-40 to +125
°C
Tsol
270
°C
Parameter
Input
Output
Isolation voltage
*1
*2
*3
*4
*1
Soldering temperature *2
40 to 60%RH, AC for 1minute, f=60Hz
for 10s
Refer to Fig.1,Fig.2
f=50Hz sine wave
1mm
Symbol
Ta=25°C
Unit
Soldering area
■Electrical Characteristics
Input
Output
Transfer
characteristics
Parameter
Symbol
Forward voltage
VF
Reverse current
Repetitive peak
off-state current
On-state voltage
IR
Holding current
Critical rate of rise of
off-state voltage
Minimum trigger current
Ta=25°C
MAX. Unit
MIN.
TYP.
IF=20mA
-
1.2
1.4
V
VR=3V
-
-
10
μA
VD=VDRM
-
-
100
μA
VT
IT=1.2A
-
-
2.5
V
IH
VD=6V
-
-
25
mA
100
-
-
V/μs
-
-
10
mA
-
Ω
100
μs
IDRM
dv/dt
IFT
Conditions
VD=1/√2· VDRM
VD=6V, RL=100Ω
Isolation resistance
RISO
DC500V 40 to 60%RH
Turn on time
tON
VD=6V, RL=100Ω,
IF=20mA
5×10
10
10
11
-
-
VDRM
[V]
Rating
Voltage
[V]
Rank
mark
IFT [mA]
(VD=6V,
RL=100Ω)
600
AC250
1
MAX.10
■Model Line-up
Lead Form
Shipping
Packege
DIN
EN60747-5-5
Model No.
Through-Hole
Sleeve
50 pcs/sleeve
SMT Gullwing
Taping
1,000 pcs/reel
-
Approved
-
Approved
PR3BMF51NSLF
PR3BMF51YSLF
PR3BMF51NPLF
PR3BMF51YPLF
Please contact a local SHARP sales representative to inquire about production status.
Sheet No.: OP14009EN
4
PR3BMF51NSLF Series
Sheet No.: OP14009EN
5
PR3BMF51NSLF Series
Sheet No.: OP14009EN
6
PR3BMF51NSLF Series
■ Design Considerations
● Recommended Operating Conditions
Input
Output
Parameter
Input signal current
at ON state
Input signal current
at OFF state
Load supply voltage
Load supply current
Frequency
Operating temperature
Symbol
Condition
MIN
MAX
Unit
IF(ON)
-
20
25
mA
IF(OFF)
-
0
0.1
mA
-
-
240
V
-
IT(rms)×
80%(*)
A
50
-20
60
80
Hz
˚C
VOUT(rms)
IOUT(rms)
Locate snubber circuit between output terminals
(Cs=0.022μ F, Rs=47Ω )
-
f
Topr
(*) See Fig.2 about derating curve (IT(rms) vs. ambient temperature).
●Design guide
In order for the SSD to turn off, the triggering current (IF) must be 0.1mA or less
In phase control applications or where the SSD is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if
the voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation, please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit values to start with : Cs=0.022μF and Rs=47Ω. The operation of the SSD
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenods.
Following the procedure outlined above should provide sufficient results.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main output triac as possible.
All pins shall be used by soldering on the board. (Socket and others shall not be used.)
● Degradation
In general, the emission of the IRED used in SSD will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSDs should provide at least
twice the minimum required triggering current from initial operation.
Sheet No.: OP14009EN
7
PR3BMF51NSLF Series
● Recommended Foot Print (reference)
SMT Gullwing Lead-form
1.7
2.54
2.54
2.54
8.2
2.2
(Unit : mm)
● Standard Circuit
R1
②
+Vcc
D1
Load
Zs
SSD
③
V1
⑧
AC Line
⑥
Tr1
✩ For additional design
assistance, please review our corresponding Optoelectronic Application Notes.
Sheet No.: OP14009EN
8
PR3BMF51NSLF Series
■ Manufacturing Guidelines
● Soldering Method
Reflow Soldering:
Reflow soldering should follow the temperature profile shown below.
Soldering should not exceed the curve of temperature profile and time.
Please don't solder more than twice.
(℃)
300
Terminal : 260˚C peak
(package surface : 250˚C peak)
200
Reflow
220˚C or more, 60s or less
Preheat
100
150 to 180˚C, 120s or less
0
0
1
3
2
4
(min)
Flow Soldering (No Solder bathing)
Flow soldering should be completed below 270˚C and
within 10s. Preheating is within the bounds of 100 to
150˚C and 30 to 80s. Please don't solder more than
twice.
Hand soldering
Hand soldering should be completed within 3s when the point of solder iron is
below 400C. Please don't solder more than twice.
Other notice
Please test the soldering method in actual condition and make sure the soldering works
fine, since the im- pact on the junction between the device and PCB varies depending
on the tooling and soldering conditions
Sheet No.: OP14009EN
9
PR3BMF51NSLF Series
● Cleaning instructions
Solvent cleaning :
Solvent temperature should be 45˚C or below. Immersion time should be 3minutes or less.
Ultrasonic cleaning :
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output,
cleaning time, size of PCB and mounting method of the device.
Therefore, please make sure the device withstands the ultrasonic cleaning in actual
conditions in advance of mass production.
Recommended solvent materials :
Ethyl alcohol, Methyl alcohol and Isopropyl alcohol
In case the other type of solvent materials are intended to be used, please make sure
they work fine in actual using conditions since some materials may erode the packaging resin.
● Presence of ODC
This product shall not contain the following materials.
And they are not used in the production process for this device.
Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBB and PBDE are not used in this product at all.
The RoHS directive(2011/65/EU)
This product complies with the RoHS directive(2011/65/EU) .
Object substances: mercury, lead, cadmium, hexavalent chromium, polybrominated
biphenyls(PBB)and polybrominated diphenyl ethers(PBDE)
Content of six substances specified in Management Methods for Control of Pollution
Caused by Electronic Information Products Regulation
(Chinese : 电子信息产品污染控制管理办法).
Marking Styles for the Names and Contents of the Hazardous Substances
Hazardous Substances
Category
Solid State
Device
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
chromium
(Cr6+)
×
○
○
○
Polybrominate
d biphenyls
(PBB)
Polybrominate
d diphenyl
ethers
(PBDE)
○
○
This table is prepared in accordance with the provisions of SJ/T 11364.
○:Indicates that said hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement of GB/T 26572
×:Indicates that said hazardous substance contained in at least one of the
homogeneous materials used for this part is above the limit requirement
of GB/T 26572
The marking "×" in the above table indicates the exemption of RoHS directive
(2011/65/EU), where the elimination or substitution of the restrictive substances
is still immature technically and impracticable economically from a current scientific view.
Sheet No.: OP14009EN
10
PR3BMF51NSLF Series
■ Package specification
● Sleeve package
Trough-Hole
Package materials
Sleeve : HIPS or ABS with preventing static electricity
Stopper : Styene-Elastomer
Package method
MAX. 50pcs of products shall be packaged in a sleeve.
80th ends shall be closed by tabbed and tabless stoppers.
The product shall be arranged in the sleeve with its anode mark on the tabless stopper side.
MAX. 20 sleeves in one case.
Sleeve outline dimensions
12
5.8
10.8
520±2
8-R0.5
6.7
(Unit : mm)
Sheet No.: OP14009EN
11
PR3BMF51NSLF Series
● Tape and Reel package
SMT Gullwing
Package materials
Carrier tape : A-PET or PS (with preventing anti-static material)
Cover tape : PET (three layer system)
Reel : PS
Carrier tape structure and Dimensions
Sheet No.: OP14009EN
12
PR3BMF51NSLF Series
■Important Notices
· The circuit application examples in this publication
are provided to explain representative applications
of SHARP devices and are not intended to
guarantee any circuit design or license any
intellectual property rights. SHARP takes no
responsibility for any problems related to any
intellectual property right of a third party resulting
from the use of SHARP's devices.
with equipment that requires higher reliability such
as:
--- Transportation control and safety equipment
(i.e.,aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in
connection with equipment that requires an
extremely high level of reliability and safety such
as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment
(e.g.,scuba).
· Contact SHARP in order to obtain the latest
device specification sheets before using any
SHARP device. SHARP reserves the right to make
changes in the specifications, characteristics, data,
materials, structure, and other contents described
herein at any time without notice in order to
improve design or reliability. Manufacturing
locations are also subject to change without notice.
· Observe the following points when using any
devices in this publication. SHARP takes no
responsibility for damage caused by improper use
of the devices which does not meet the conditions
and absolute maximum ratings to be used specified
in the relevant specification sheet nor meet
thefollowing conditions:
(i) The devices in this publication are designed for
use in general electronic equipment designs such
as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and
redundant design should be taken to ensure
reliability and safety when SHARP devices are used
for or in connection
· If the SHARP devices listed in this publication fall
within the scope of strategic products described in
the Foreign Exchange and Foreign Trade Law of
Japan, it is necessary to obtain approval to export
such SHARP devices.
· This publication is the proprietary product of
SHARP and is copyrighted, with all rights reserved.
Under the copyright laws, no part of this publication
may be reproduced or transmitted in any form or by
any means, electronic or mechanical, for any
purpose, in whole or in part, without the express
written permission of SHARP. Express written
permission is also required before any use of this
publication may be made by a third party.
· Contact and consult with a SHARP representative
if there are any questions about the contents of this
publication.
Sheet No.: OP14009EN
13