6EP13331LD00

Data sheet 6EP1333-1LD00 SITOP PSU100D/1AC/24VDC/6.2A PSU100D 24 V/6,2 A Stabilized power supply input: 100-240 V AC output: 24 V DC/6.2 A Input Input 1-phase AC Rated voltage value Vin rated 100 ... 240 V Voltage range AC 85 ... 264 V Wide-range input Yes Mains buffering at Vin = 115/230 V Mains buffering at Iout rated, min. 15 ms; at Vin = 115/230 V Rated line frequency 1 50 Hz Rated line frequency 2 60 Hz Rated line range 47 ... 63 Hz input current ● at rated input voltage 100 V 3.1 A ● at rated input voltage 240 V 2A Switch-on current limiting (+25 °C), max. 75 A I²t, max. 6.5 A²·s Built-in incoming fuse internal Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: from 10 A characteristic C or from 16 A characteristic B Output Output Controlled, isolated DC voltage Rated voltage Vout DC 24 V Total tolerance, static ± 2% Static mains compensation, approx. 0.5 % Static load balancing, approx. 1% Residual ripple peak-peak, max. 100 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 100 mV Adjustment range 22 ... 28 V product function output voltage adjustable Yes Output voltage setting via potentiometer Status display Green LED for 24 V OK On/off behavior Overshoot of Vout < 2 % Startup delay, max. 1s voltage increase time of the output voltage maximum 30 ms Rated current value Iout rated 6.2 A Current range 0 ... 6.2 A 6EP13331LD00 Page 1/2 1.15.2021 Subject to change without notice © Copyright Siemens ● Note +50 ... +70 °C: Derating 2.5%/K supplied active power typical 150 W Parallel switching for enhanced performance Yes Numbers of parallel switchable units for enhanced performance 2 Efficiency Efficiency at Vout rated, Iout rated, approx. 86 % Power loss at Vout rated, Iout rated, approx. 24 W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.5 % Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. 5% Protection and monitoring Output overvoltage protection < 35 V Current limitation, typ. 7.4 A property of the output short-circuit proof Yes Short-circuit protection Electronic shutdown, automatic restart enduring short circuit current RMS value ● typical Overload/short-circuit indicator 16 A - Safety Primary/secondary isolation Yes galvanic isolation Safety extra low output voltage Vout according to EN 60950-1 Protection class Class I leakage current ● maximum 3.5 mA ● typical 1 mA Degree of protection (EN 60529) IP20 Approvals CE mark Yes UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus (UL 60950-1, CSA C22.2 No. 60950-1), File E151273 Explosion protection - certificate of suitability NEC Class 2 No FM approval - CB approval Yes Marine approval - EMC Emitted interference EN 55022 Class B Supply harmonics limitation - Noise immunity EN 61000-6-2 environmental conditions ambient temperature ● during operation — Note -10 ... +70 °C with natural convection ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C Mechanics Connection technology screw-type terminals Connections ● Supply input L, N, PE: 1 screw terminal each for 0.3 ... 1.3 mm² single-core/finely stranded ● Output +, -: 2 screw terminals each for 0.3 ... 1.3 mm² ● Auxiliary - width of the enclosure 97 mm height of the enclosure 178 mm depth of the enclosure 38 mm required spacing ● top 6EP13331LD00 Page 2/3 20 mm 1.15.2021 Subject to change without notice © Copyright Siemens ● bottom 0 mm ● left 20 mm ● right 20 mm Weight, approx. 0.55 kg Installation Wall mounting other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) 6EP13331LD00 Page 3/3 1.15.2021 Subject to change without notice © Copyright Siemens