6EP13342AA010AB0

Data sheet 6EP1334-2AA01-0AB0 SITOP SMART/1AC/24VDC/10A/WALL MOUNTING SITOP smart 240 W Stabilized power supply input: 120/230 V AC, output: DC 24 V/10 A Option for for wall mounting Input Input ● Note 1-phase AC Set by means of selector switch on the device supply voltage ● 1 at AC rated value 120 V ● 2 at AC rated value 230 V input voltage ● 1 at AC 85 ... 132 V ● 2 at AC 170 ... 264 V Wide-range input No Overvoltage resistance 2.3 × Vin rated, 1.3 ms Mains buffering at Vin = 93/187 V Mains buffering at Iout rated, min. 20 ms; at Vin = 93/187 V Rated line frequency 1 50 Hz Rated line frequency 2 60 Hz Rated line range 47 ... 63 Hz input current ● at rated input voltage 120 V 4.1 A ● at rated input voltage 230 V 2.4 A Switch-on current limiting (+25 °C), max. 65 A duration of inrush current limiting at 25 °C ● typical 3 ms I²t, max. 3.3 A²·s Built-in incoming fuse T 6.3 A/250 V (not accessible) Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: from 10 A characteristic C Output Output Controlled, isolated DC voltage Rated voltage Vout DC 24 V Total tolerance, static ± 3% Static mains compensation, approx. 0.1 % Static load balancing, approx. 0.5 % Residual ripple peak-peak, max. 150 mV Residual ripple peak-peak, typ. 50 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 240 mV 6EP13342AA010AB0 Page 1/2 1.14.2021 Subject to change without notice © Copyright Siemens Spikes peak-peak, typ. (bandwidth: 20 MHz) 150 mV Adjustment range 22.8 ... 28 V product function output voltage adjustable Yes Output voltage setting via potentiometer Status display Green LED for 24 V OK On/off behavior Overshoot of Vout approx. 4 % Startup delay, max. 0.1 s Voltage rise, typ. 50 ms Rated current value Iout rated 10 A Current range 0 ... 12 A ● Note supplied active power typical 12 A up to +45 °C 288 W short-term overload current ● on short-circuiting during the start-up typical 30 A ● at short-circuit during operation typical 33 A duration of overloading capability for excess current ● on short-circuiting during the start-up 100 ms ● at short-circuit during operation 200 ms Parallel switching for enhanced performance Yes Numbers of parallel switchable units for enhanced performance 2 Efficiency Efficiency at Vout rated, Iout rated, approx. 90 % Power loss at Vout rated, Iout rated, approx. 27 W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.3 % Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. 1% Load step setting time 50 to 100%, typ. 0.2 ms Load step setting time 100 to 50%, typ. 0.2 ms Protection and monitoring Output overvoltage protection < 33 V Current limitation 12.5 ... 13.5 A property of the output short-circuit proof Yes Short-circuit protection Constant current characteristic enduring short circuit current RMS value ● typical Overload/short-circuit indicator 16 A - Safety Primary/secondary isolation Yes galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 Protection class Class I leakage current ● maximum 3.5 mA ● typical 0.8 mA Degree of protection (EN 60529) IP20 Approvals CE mark Yes UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259 Explosion protection - certificate of suitability NEC Class 2 No FM approval - CB approval Yes Marine approval - EMC Emitted interference EN 55022 Class B Supply harmonics limitation - Noise immunity EN 61000-6-2 environmental conditions 6EP13342AA010AB0 Page 2/3 1.14.2021 Subject to change without notice © Copyright Siemens ambient temperature ● during operation — Note 0 ... 60 °C with natural convection ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C Humidity class according to EN 60721 Climate class 3K3, 5 … 95% no condensation Mechanics Connection technology screw-type terminals Connections ● Supply input L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² single-core/finely stranded ● Output L+, M: 2 screw terminals each for 0.5 ... 2.5 mm² ● Auxiliary - width of the enclosure 70 mm height of the enclosure 125 mm depth of the enclosure 125 mm required spacing ● top 50 mm ● bottom 50 mm ● left 0 mm ● right 0 mm Weight, approx. 0.85 kg product feature of the enclosure housing can be lined up Yes Installation Wall mounting MTBF at 40 °C 1 460 803 h other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) 6EP13342AA010AB0 Page 3/3 1.14.2021 Subject to change without notice © Copyright Siemens