Metallized Jump to preceding page Polyester Film Capacitors (MKT) Uncoated (Silver Caps)
B 32 560 … B 32 564
Extremely small dimensions Versions with special dimensions can be supplied at short notice Construction
q Dielectric: polyethylene terephthalate
Cut surfaces
(polyester)
q Stacked-film technology q Uncoated
Dimensions in mm Features
q Special dimensions available upon request q High pulse strength q Minimum tensile strength of leads >10 N
Typical applications
q q q q
Standard applications Electronic lamp ballast circuits Energy-saving lamps Substitute for electrolytics in electronic lamp ballasts (420 Vdc)
Lead spacing ± 0,4 7,5 10,0 15,0 22,5 27,5
Diameter d1 0,5 0,5 0,6 0,8 0,8
Type B 32 560 B 32 561 B 32 562 B 32 563 B 32 564
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
Terminals
q Parallel wire leads, tinned q Also available with (3,0 ± 0,5) mm
lead length upon request Marking Rated capacitance (coded), rated dc voltage Delivery mode Bulk (untaped) Taped (AMMO pack or reel) for lead spacing ≤ 15,0 mm. For notes on taping, refer to page 279. Detail specification Homologated in accordance with CECC 30 401-007 Notes on mounting When mounting these capacitors, take into account creepage distances and clearances to adjacent live parts. The insulating strength of the cut surfaces to other live parts of the circuit is 1,5 times the capacitors rated dc voltage, but is always at least 300 Vdc. Capacitors with 7,5 mm lead spacing are only suitable for use with single-clad printed circuit boards.
Siemens Matsushita Components
53
B 32 560 … B 32 564
MKT
Overview of available types Lead 7,5 mm spacing Type B 32 560 Page 55 1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 0,33 µF 0,47 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 5,6 µF1) 6,8 µF 10 µF 15 µF 22 µF 33 µF 100 Vdc 63 Vdc 10 mm B 32 561 57 15 mm B 32 562 58 22,5 mm B 32 563 59 27,5 mm B 32 564 60
400 Vdc
630 Vdc
250 Vdc
250 Vdc
400 Vdc
400 Vdc
630 Vdc
1) For B 32 564, 420 Vdc only
54
Siemens Matsushita Components
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
100 Vdc
250 Vdc
250 Vdc
400 Vdc
100 Vdc
100 Vdc
250 Vdc
400 Vdc 420 Vdc
100 Vdc
B 32 560
MKT
7,5 Ordering codes and packing units, lead spacing 7,5 mm
VR (Vrms, f ≤ 60 Hz)
63 Vdc (40 Vac)
CR
Maximum dimensions b × h × l (mm)
Ordering code1)
Packing units (pcs) Ammo Reel pack
2) 2) 2) 2)
Untaped 2500 2500 2000 1500 1000 500 500 350 250 150 3000 3000 2000 1500 1200 1000 500 400 300 3000 2300 1700 1200 1000 650 500
100 Vdc (63 Vac)
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
250 Vdc (160 Vac)
0,22 µF 2,5 × 5,2 × 9,0 0,33 µF 2,5 × 5,6 × 9,0 0,47 µF 2,6 × 5,8 × 9,0 0,68 µF 3,2 × 6,2 × 9,0 1,0 µF 4,0 × 6,8 × 9,0 1,5 µF 5,1 × 7,6 × 9,0 2,2 µF 6,5 × 8,2 × 9,0 3,3 µF 8,5 × 9,1 × 9,0 4,7 µF 9,8 × 11,0 × 9,0 6,8 µF 11,5 × 13,3 × 9,0 0,10 µF 2,5 × 4,7 × 9,0 0,15 µF 2,5 × 4,7 × 9,0 0,22 µF 2,5 × 5,1 × 9,0 0,33 µF 2,7 × 5,7 × 9,0 0,47 µF 3,4 × 6,1 × 9,0 0,68 µF 4,2 × 6,5 × 9,0 1,0 µF 5,5 × 7,0 × 9,0 1,5 µF 6,7 × 8,2 × 9,0 2,2 µF 8,5 × 9,2 × 9,0 33 nF 2,5 × 4,8 × 9,0 47 nF 2,5 × 5,2 × 9,0 68 nF 2,6 × 5,7 × 9,0 0,10 µF 3,2 × 6,1 × 9,0 0,15 µF 3,9 × 7,0 × 9,0 0,22 µF 4,9 × 7,5 × 9,0 0,33 µF 6,4 × 8,2 × 9,0
B32560-J224-+ B32560-J334-+ B32560-J474-+*** B32560-J684-+*** B32560-J105-+*** B32560-J155-+*** B32560-J225-+*** B32560-J335-+ B32560-J475-+ B32560-J685-+ B32560-J1104-+ B32560-J1154-+ B32560-J1224-+*** B32560-J1334-+*** B32560-J1474-+*** B32560-J1684-+*** B32560-J1105-+*** B32560-J1155-+ B32560-J1225-+ B32560-J3333-+ B32560-J3473-+*** B32560-J3683-+*** B32560-J3104-+*** B32560-J3154-+*** B32560-J3224-+*** B32560-J3334-+
3250 2850 2200 1700 1300 – – –
2) 2)
2600 2300 1800 1400 1100 – – –
2) 2)
3400 3100 2500 2000 1600 – –
2)
2700 2500 2000 1600 1300 – –
2)
3500 3400 2650 2150 1750 –
2800 2700 2200 1800 1400 –
Capacitance tolerance: ± 20 % = M, ± 10 % = K, ± 5 % = J ˆ ˆ ˆ Special dimensions available upon request. For corresponding design rules, refer to page 238.
1) Replace the + by the code letter for the required capacitance tolerance. Replace the *** by the code number for the required packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. 2) Taping upon request
Siemens Matsushita Components
55
MKT
B 32 560
7,5 Ordering codes and packing units, lead spacing 7,5 mm
VR (Vrms, f ≤ 60 Hz)
400 Vdc (200 Vac)
CR
Maximum dimensions b × h × l (mm) 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,6 × 6,0 × 9,0 3,2 × 6,5 × 9,0 3,8 × 7,3 × 9,0 4,9 × 7,7 × 9,0 6,5 × 8,2 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 2,5 × 5,5 × 9,0 3,2 × 6,5 × 9,0 3,8 × 7,5 × 9,0
Ordering code1)
Packing units (pcs) Ammo Reel pack
2) 2)
Untaped 2300 2000 2100 2000 2000 2000 2200 2500 2300 1600 1200 1000 500 500 2300 2000 2100 2000 1800 1300 1000
3500 3700 3400 3400 2900 2400
2900 3000 2800 2700 2400 2000
Capacitance tolerance: ± 20 % = M, ± 10 % = K, ± 5 % = J ˆ ˆ ˆ Special dimensions available upon request. For corresponding design rules, refer to page 238.
1) Replace the + by the code letter for the required capacitance tolerance. Replace the *** by the code number for the required packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. 2) Taping upon request
56
Siemens Matsushita Components
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
630 Vdc (400 Vac)
1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 6,8 nF 10 nF
B32560-J6102-+ B32560-J6152-+*** B32560-J6222-+*** B32560-J6332-+*** B32560-J6472-+*** B32560-J6682-+*** B32560-J6103-+*** B32560-J6153-+*** B32560-J6223-+*** B32560-J6333-+*** B32560-J6473-+*** B32560-J6683-+*** B32560-J6104-+*** B32560-J6154-+ B32560-J8102-+ B32560-J8152-+*** B32560-J8222-+*** B32560-J8332-+*** B32560-J8472-+*** B32560-J8682-+*** B32560-J8103-+***
3500 3700 3400 3700 3700 3500 3500 3400 3400 2650 2250 1750 –
2)
2900 3000 2800 3000 3000 2800 2800 2700 2700 2200 1900 1400 –
2)
B 32 561
MKT
10 Ordering codes and packing units, lead spacing 10 mm
VR (Vrms, f ≤ 60 Hz)
100 Vdc (63 Vac)
CR
Maximum dimensions b × h × l (mm) 2,5 × 5,2 × 11,5 2,9 × 5,8 × 11,5 3,6 × 6,3 × 11,5 4,5 × 6,9 × 11,5 5,6 × 7,8 × 11,5 6,9 × 9,0 × 11,5 2,5 × 4,4 × 11,5 2,5 × 4,8 × 11,5 2,8 × 5,3 × 11,5 3,3 × 6,0 × 11,5 4,2 × 6,6 × 11,5 5,2 × 7,5 × 11,5 6,3 × 8,5 × 11,5 2,5 × 5,1 × 11,5 2,5 × 5,1 × 11,5 2,5 × 5,1 × 11,5 2,5 × 5,1 × 11,5 2,6 × 6,0 × 11,5 3,2 × 6,6 × 11,5 4,0 × 6,9 × 11,5 5,2 × 7,7 × 11,5 6,6 × 8,5 × 11,5
Ordering code1)
250 Vdc (160 Vac)
400 Vdc (200 Vac)
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
0,33 µF 0,47 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 0,33 µF 0,47 µF 10 nF 15 nF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF
B32561-J1334-+*** B32561-J1474-+*** B32561-J1684-+*** B32561-J1105-+*** B32561-J1155-+*** B32561-J1225-+ B32561-J3473-+ B32561-J3683-+*** B32561-J3104-+*** B32561-J3154-+*** B32561-J3224-+*** B32561-J3334-+*** B32561-J3474-+*** B32561-J6103-+*** B32561-J6153-+*** B32561-J6223-+*** B32561-J6333-+*** B32561-J6473-+*** B32561-J6683-+*** B32561-J6104-+*** B32561-J6154-+*** B32561-J6224-+
Packing units (pcs) Ammo Reel pack 1750 2400 1560 2300 1260 2000 1050 1500 810 1200 – –
2) 2)
Untaped 1600 1200 1000 500 500 400 2300 1800 1300 1000 700 500 400 1700 2000 2000 1700 1300 1000 700 500 300
1760 1600 1300 1040 850 700 1760 1830 1830 1760 1760 1390 1090 850 –
2400 2300 2000 1600 1300 1000 2400 2500 2500 2400 2400 2100 1700 1300 –
Capacitance tolerance: ± 20 % = M, ± 10 % = K, ± 5 % = J ˆ ˆ ˆ Special dimensions available upon request. For corresponding design rules, refer to page 238.
1) Replace the + by the code letter for the required capacitance tolerance. Replace the *** by the code number for the required packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter. 2) Taping upon request
Siemens Matsushita Components
57
MKT
B 32 562
15 Ordering codes and packing units, lead spacing 15 mm
VR (Vrms, f ≤ 60 Hz)
100 Vdc (63 Vac)
CR
Maximum dimensions b × h × l (mm) 3,2 × 6,3 × 16,5 4,0 × 7,3 × 16,5 4,9 × 8,0 × 16,5 6,0 × 9,3 × 16,5 7,3 × 10,6 × 16,5 9,0 × 11,8 × 16,5 11,8 × 13,0 × 16,5 3,2 × 5,6 × 16,5 4,0 × 6,2 × 16,5 5,0 × 6,7 × 16,5 6,0 × 7,8 × 16,5 7,0 × 9,3 × 16,5 8,7 × 11,0 × 16,5 10,7 × 12,8 × 16,5 13,9 × 14,5 × 16,5 3,3 × 5,6 × 16,5 3,3 × 5,6 × 16,5 3,3 × 5,6 × 16,5 3,3 × 5,6 × 16,5 3,3 × 5,6 × 16,5 3,9 × 6,5 × 16,5 4,7 × 7,5 × 16,5 6,0 × 8,3 × 16,5 7,3 × 9,3 × 16,5 8,9 × 10,8 × 16,5 10,9 × 12,5 × 16,5 6,2 × 9,3 × 16,5 7,6 × 10,8 × 16,5 9,2 × 12,2 × 16,5 11,2 × 14,2 × 16,5 13,5 × 16,3 × 16,5
Ordering code1)
250 Vdc (160 Vac)
400 Vdc (200 Vac)
630 Vdc (350 Vac)
Capacitance tolerance: ± 20 % = M, ± 10 % = K, ± 5 % = J ˆ ˆ ˆ Special dimensions available upon request. For corresponding design rules, refer to page 238.
1) Replace the + by the code letter for the required capacitance tolerance. Replace the *** by the code number for the required packing: Ammo pack = 289, reel = 189 The ordering code for untaped components ends after the tolerance code letter.
58
Siemens Matsushita Components
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 6,8 µF 10 µF 0,22 µF 0,33 µF 0,47 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 22 nF 33 nF 47 nF 68 nF 0,10 µF 0,15 µF 0,22 µF 0,33 µF 0,47 µF 0,68 µF 1,0 µF 0,10 µF 0,15 µF 0,22 µF 0,33 µF 0,47 µF
B32562-J1105-+*** B32562-J1155-+*** B32562-J1225-+*** B32562-J1335-+*** B32562-J1475-+*** B32562-J1685-+*** B32562-J1106-+ B32562-J3224-+*** B32562-J3334-+*** B32562-J3474-+*** B32562-J3684-+*** B32562-J3105-+*** B32562-J3155-+*** B32562-J3225-+ B32562-J3335-+ B32562-J6223-+*** B32562-J6333-+*** B32562-J6473-+*** B32562-J6683-+*** B32562-J6104-+*** B32562-J6154-+*** B32562-J6224-+*** B32562-J6334-+*** B32562-J6474-+*** B32562-J6684-+*** B32562-J6105-+ B32562-J8104-+ B32562-J8154-+ B32562-J8224-+ B32562-J8334-+ B32562-J8474-+
Packing units (pcs) Ammo Reel pack 1750 2000 1460 1500 1190 1300 960 1000 790 900 640 700 – – 1750 2000 1460 1500 1190 1300 960 1000 830 900 660 700 – – – – 1750 2000 1750 2000 1870 2100 1800 2000 1700 1900 1420 1600 1240 1300 960 1000 790 900 640 700 – – – – – – – – – – – –
Untaped 1500 1000 800 500 400 290 200 1700 1200 950 500 500 300 200 150 1800 1800 1800 1800 1600 1200 850 500 450 300 200 700 500 350 250 180
B 32 563
MKT
22,5 Ordering codes and packing units, lead spacing 22,5 mm
VR (Vrms, f ≤ 60 Hz) 100 Vdc (63Vac)
CR
1,5 µF 2,2 µF 3,3 µF 4,7 µF 6,8 µF 10 µF 15 µF 22 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 0,22 µF 0,33 µF 0,47 µF 0,68 µF 1,0 µF 1,5 µF 2,2 µF
250 Vdc (160 Vac)
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
400 Vdc (200Vac)
Maximum dimensions b × h × l (mm) 5,0 × 8,0 × 24,0 5,0 × 8,2 × 24,0 5,0 × 8,2 × 24,0 5,9 × 9,0 × 24,0 7,0 × 10,5 × 24,0 8,6 × 12,2 × 24,0 10,9 × 14,0 × 24,0 12,8 × 17,2 × 24,0 4,8 × 7,2 × 24,0 5,6 × 8,2 × 24,0 6,9 × 9,5 × 24,0 8,3 × 11,2 × 24,0 10,1 × 13,5 × 24,0 12,2 × 15,5 × 24,0 5,1 × 8,0 × 24,0 5,1 × 8,0 × 24,0 5,7 × 8,3 × 24,0 6,9 × 9,6 × 24,0 8,3 × 11,2 × 24,0 10,3 × 13,2 × 24,0 12,6 × 15,5 × 24,0
Ordering code1)
Packing units (pcs) Untaped 1400 1900 1900 1600 920 960 620 360 1760 1140 920 740 700 390 1800 1700 1660 920 850 660 360
B32563-J1155-+ B32563-J1225-+ B32563-J1335-+ B32563-J1475-+ B32563-J1685-+ B32563-J1106-+ B32563-J1156-+ B32563-J1226-+ B32563-J3684-+ B32563-J3105-+ B32563-J3155-+ B32563-J3225-+ B32563-J3335-+ B32563-J3475-+ B32563-J6224-+ B32563-J6334-+ B32563-J6474-+ B32563-J6684-+ B32563-J6105-+ B32563-J6155-+ B32563-J6225-+
Capacitance tolerance: ± 20 % = M, ± 10 % = K, ± 5 % = J ˆ ˆ ˆ Special dimensions available upon request. For corresponding design rules, refer to page 238.
1) Replace the + by the code letter for the required capacitance tolerance.
Siemens Matsushita Components
59
MKT
B 32 564
27,5 Ordering codes and packing units, lead spacing 27,5 mm
VR (Vrms , f ≤ 60 Hz) 100 Vdc (63Vac)
CR
4,7 µF 6,8 µF 10 µF 15 µF 22 µF 33 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 6,8 µF 10 µF 1,0 µF 1,5 µF 2,2 µF 3,3 µF 4,7 µF 4,7 µF 5,6 µF 6,8 µF
250 Vdc (160 Vac)
400 Vdc (200 Vac)
420 Vdc (200 Vac)
Capacitance tolerance: ± 20 % = M, ± 10 % = K, ± 5 % = J ˆ ˆ ˆ Special dimensions available upon request. For corresponding design rules, refer to page 238.
1) Replace the + by the code letter for the required capacitance tolerance.
60
Siemens Matsushita Components
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
Maximum dimensions b × h × l (mm) 5,6 × 8,3 × 29,0 6,3 × 9,5 × 29,0 7,6 × 11,0 × 29,0 9,1 × 13,5 × 29,0 11,0 × 16,0 × 29,0 13,0 × 19,8 × 29,0 5,1 × 7,6 × 29,0 5,3 × 10,2 × 29,0 6,4 × 11,8 × 29,0 7,9 × 14,0 × 29,0 9,6 × 15,8 × 29,0 11,9 × 18,0 × 29,0 13,8 × 22,5 × 29,0 6,8 × 11,2 × 29,0 7,8 × 14,2 × 29,0 9,6 × 16,4 × 29,0 12,2 × 18,8 × 29,0 14,2 × 22,8 × 29,0 16,0 × 20,0 × 29,0 16,0 × 20,0 × 29,0 16,0 × 20,0 × 29,0
Ordering code1)
Packing units (pcs) Untaped 1000 820 680 430 320 360 1620 970 920 750 400 300 280 750 750 400 330 260 290 290 290
B32564-J1475-+ B32564-J1685-+ B32564-J1106-+ B32564-J1156-+ B32564-J1226-+ B32564-J1336-+ B32564-J3105-+ B32564-J3155-+ B32564-J3225-+ B32564-J3335-+ B32564-J3475-+ B32564-J3685-+ B32564-J3106-+ B32564-J6105-+ B32564-J6155-+ B32564-J6225-+ B32564-J6335-+ B32564-J6475-+ B32564-T6475-K B32564-T6565-K B32564-T6685-K
B 32 560 … B 32 564
MKT
Technical data Climatic category in accordance with IEC 68-1 Lower category temperature Tmin Upper category temperature Tmax Damp heat test Limit values after damp heat test1) 55/100/561) − 55 °C + 100 °C (+ 125 °C for 1000 h and VC = 0,5 ⋅ VR) 56 days/40 °C/93 % relative humidity Capacitance change |∆C/C| ≤5% Dissipation factor change ∆ tan δ ≤ 3 ⋅ 10−3 (at 1 kHz) ≤ 5 ⋅ 10−3 (at 10 kHz) Insulation resistance Ris ≥ 50 % of minimum or time constant τ = CR ⋅ Ris as-delivered values 0,5 ⋅ VR; 40 °C 2 ⋅10−9/h = 2 fit For a conversion table for other operating conditions and temperatures, refer to page 276. 200 000 h Short circuit or open circuit Capacitance change |∆C/C| > 10 % Dissipation factor tan δ > 2 ⋅ upper limit value Insulation resistance Ris < 150 MΩ (CR ≤ 0,33 µF) or time constant τ = CR ⋅ Ris < 50 s (CR > 0,33 µF) 1,4 ⋅ VR, 2 s T ≤ 85 °C: VC = 1,0 ⋅ VR or 1,0 ⋅ Vrms T ≤ 100 °C: VC = 0,8 ⋅ VR or 0,8 ⋅ Vrms
Reliability: Reference conditions Failure rate
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
Service life Failure criteria: Total failure Failure due to variation of parameters
DC test voltage Category voltage VC Operation with dc voltage or ac voltage Vrms up to 60 Hz Category voltage for short operating periods Dissipation factor tan δ (in 10−3) at 20 °C (upper limit values)
T ≤ 100 °C: VC = 1,25 ⋅ VR or 1,0 ⋅ Vrms for max. 2000 h T ≤ 125 °C: VC = 0,5 ⋅ VR or 0,5 ⋅ Vrms for max. 1000 h
at 1 kHz 10 kHz 100 kHz
CR ≤ 0,1 µF 0,1 µF < CR ≤ 1 µF 8 8 15 15 30 – CR ≤ 0,33 µF 3750 MΩ 7500 MΩ
CR > 1 µF 10 – –
Insulation resistance Ris or time constant τ = CR ⋅ Ris at 20 °C, rel. humidity ≤ 65 % (minimum as-delivered values)
VR ≤ 100 Vdc ≥ 250 Vdc
CR > 0,33 µF 1250 s 2500 s
1) According to CECC 30401-007, test criteria must be met after exposure to damp heat for 21 days.
Siemens Matsushita Components
61
B 32 560 … B 32 564
MKT
Impedance Z versus frequency f (typical values)
Pulse handling capability Maximum permissible voltage change per unit of time for non-sinusoidal voltages (pulse, sawtooth).
VR
63 Vdc 100 Vdc 250 Vdc 400 Vdc 420 Vdc 630 Vdc
Max. rate of voltage rise Vpp/τ in V/µs (for Vpp = VR) Lead spacing 7,5 mm 10 mm 15 mm 22,5 mm 120 – – – 150 75 50 50 200 150 100 100 275 175 125 125 – – – – 320 – 150 –
27,5 mm – 25 50 60 60 –
For Vpp < VR , the permissible voltage rise rate value Vpp/τ may be multiplied by the factor VR/Vpp. Also refer to the calculation example on page 250.
VR
63 Vdc 100 Vdc 250 Vdc 400 Vdc 420 Vdc 630 Vdc
Pulse characteristic k0 in V2/µs (for Vpp ≤ VR) Lead spacing 7,5 mm 10 mm 15 mm 15 000 – – 30 000 15 000 10 000 100 000 75 000 50 000 220 000 140 000 100 000 – – – 400 000 – 190 000
22,5 mm – 10 000 50 000 100 000 – –
27,5 mm – 5 000 25 000 50 000 50 000 –
62
Siemens Matsushita Components
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
B 32 560
MKT
7,5 Permissible ac voltage Vrms versus frequency f Lead spacing 7,5 mm 63 Vdc/ 40 Vac 100 Vdc/ 63 Vac
Vac
Vac
Vrms
Vrms
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
250Vdc/ 160Vac
400 Vdc/ 200 Vac
Vac
Vac
Vrms
Vrms
Siemens Matsushita Components
63
MKT
B 32 560
7,5 Permissible ac voltage Vrms versus frequency f Lead spacing 7,5 mm 630 Vdc/ 400 Vac
64
Siemens Matsushita Components
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
B 32 561
MKT
10 Permissible ac voltage Vrms versus frequency f Lead spacing 10 mm 100 Vdc/ 63 Vac 250 Vdc/ 160 Vac
Vac
Vac
Vrms
Vrms
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
400 Vdc/ 200 Vac
Vac
Vrms
Siemens Matsushita Components
65
MKT
B 32 562
15 Permissible ac voltage Vrms versus frequency f Lead spacing 15 mm 100 Vdc/63 Vac 250 Vdc/ 160 Vac
Vac
Vac
Vrms
Vrms
400 Vdc/200 Vac
630 Vdc/350 Vac
Vac
Vrms
66
Siemens Matsushita Components
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
B 32 563
MKT
22,5 Permissible ac voltage Vrms versus frequency f Lead spacing 22,5 mm 100 Vdc/ 63 Vac 250 Vdc/ 160 Vac
Vac
Vac
Vrms
Vrms
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564
400 Vdc/ 200 Vac
Vac
Vrms
Siemens Matsushita Components
67
MKT
B 32 564
Jump to succeding page
27,5 Permissible ac voltage Vrms versus frequency f Lead spacing 27,5 mm 100 Vdc/ 63 Vac 250 Vdc/ 160 Vac
400 Vdc/ 200 Vac
Vac
Vrms
68
Siemens Matsushita Components
/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32560-564