SDA4331

PLL with I2C Bus for AM/FM Receivers SDA 4331X 1 1.1 • • • • • Overview Features 155 MHz FM and 40 MHz AM input frequency 30 mVeff AM and 50 mVeff FM sensitivity Additional open drain ports controlled by I2C Bus 2-pin quartz oscillator Fast phase detector with short anti-backlash pulses P-DSO-24-1 and polarity reversal • Charge pump current programmable in four steps up to 4.5 mA • Frequency resolution of 1, 5 and 10 kHz AM and 12.5, 25 and 50 kHz FM • P-DSO-24 package Type SDA 4331X 1.2 Application Ordering Code Q67100-H5139 Package P-DSO-24-1 The SDA 4331X provides separated input and output ports for AM and FM and is well suited for extremely fast loop settling times in the FM mode. Semiconductor Group 1 04.96 SDA 4331X 1.3 Pin Configuration (top view) P-DSO-24-1 Figure 1 Semiconductor Group 2 04.96 SDA 4331X 1.4 Pin Definitions and Functions Input (I) Output (O) I I/O I Function Supply voltage digital (5 V) Clock I2C Bus Data I2C Bus Address selection, sets the LSB of the IC-address 10 V open drain output, controlled via I2C Bus 10 V open drain output, indicating the operation mode (H = AM) Input for the FM signal from VCO Ground analog I Input for the AM signal from VCO Pin No. Symbol 1 2 3 4 5 6…9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 VDD1 SCL SDA A0 N.C. SA1 … SA4 O AM/FM FMIN GNDAN AMIN N.C. N.C. O I IREF PDFM PDAM PDFMA PDAMA I O O O O Reference current, setting the base current level for the charge pumps FM charge pump output AM charge pump output Source follower output FM Source follower output AM Supply voltage digital for charge pump and source followers (up to 10 V) VDD2 OSCFB OSCIN GND I/O I Oscillator feedback, quartz terminal Oscillator input, quartz terminal, optionally input for external reference Ground digital Semiconductor Group 3 04.96 SDA 4331X 1.5 Functional Block Diagram Figure 2 Block Diagram Semiconductor Group 4 04.96 SDA 4331X 2 Functional Description The SDA 4331X is a radio PLL controlled via I2C Bus for frequency synthesis in the AM and FM range. 3 Circuit Description The reference frequency for the PLL is derived from the quartz oscillator OSC1). The R-prescaler can be adapted to quartz frequencies of 4, 8 or 10.25 MHz, respectively, yielding an internal 50 kHz reference. Programming the R-counter sets the phase detector reference frequency to 1, 5 or 10 kHz in the AM mode or to 12.5, 25 or 50 kHz in the FM mode. The VCO frequency is set by programming the A/N-counter which operates as dual-modulus counter for FM and AM using a divide by 4/5 swallow counter. The phase detector drives two different charge pumps for AM and FM mode. Additional source followers are connected to the charge pump. There are four programmable current levels for each charge pump. The supply voltage for the charge pump and the source followers is supplied via the VDD2 pin and can reach 10 V maximum. AM/FM is an open drain output as well as the additional outputs SA1 … SA4 which are controlled by I2C Bus. The I2C Bus interface provides slave receiver functions. There are two addresses selected by the A0 pin. The I2C-protocol (see diagram 1) contains one string for programming all counters and functions. The transfer may be stopped optionally after each word if the remaining functions are not to be altered. After power ON all control signals are undefined, so that the complete write sequence must be executed. 1) Pv = 2 × R1 (Π × fQ × (CO + CL) × VDD)2 R1 … Series resistance of the quartz fQ … Quartz frequency CO … Parallel capacitance of the quartz CL … Load capacitance, including input capacitance of the IC The power dissipation of the quartz is given by: Semiconductor Group 5 04.96 SDA 4331X 4 4.1 Electrical Characteristics Absolute Maximum Ratings Symbol Limit Values min. max. 6 10.5 10 t.b.d. – 40 –1 125 10.5 1 V V mW mW °C V kV – 0.3 – 0.3 – 0.3 Unit Remarks TA = – 25 °C to 85 °C Parameter Supply voltage VDD1 Supply voltage VDD2 Input voltage VIN Power dissipation per output PQ Power dissipation Ptot Storage temperature TS Output voltage SA1 … SA4, AM/FM VQH ESD voltage (HBM: 1.5 kΩ, 100 pF) VESD VDD1 + 0.3 V Note: Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. 4.2 Operational Range Symbol min. Supply voltage Supply voltage Supply current Supply current1) Ambient temperature Output voltage SA1 … SA4, AM/FM 1) Parameter Limit Values typ. 5 4 – 25 max. 5.5 10.3 10 0.5 + 85 4.5 9 Unit V V mA mA °C V VDD1 VDD2 IDD1 IDD2 TA VQH VDD2 Measurement conditions: No load on pins 17 … 20. Note: In the operating range the functions given in the circuit description are fulfilled. Semiconductor Group 6 04.96 SDA 4331X 4.3 AC/DC Characteristics Symbol Limit Values min. typ. max. Unit Test Condition Parameter Input AMIN Input voltage (sine wave) Input capacitance Input current Input FMIN Input voltage (sine wave) Input capacitance Input current Input OSCIN Input voltage (sine wave) VIN C IIN 30 4 – 50 50 mVeff VDD1 = 4.5 V 0.5 MHz < fIN < 40 MHz pF µA 0 ≤ VIN ≤ VDD1 VIN 50 120 VDD1 = 4.5 V mVeff 20 MHz < fIN < 120 MHz mVeff 10 MHz < fIN < 155 MHz 4 pF µA 0 ≤ VIN ≤ VDD1 100 C IIN – 100 VIN 100 150 200 VDD1 = 4.5 V mVeff fIN = 4 MHz mVeff fIN = 8 MHz mVeff fIN = 10.25 MHz 10 pF µA 0 ≤ VQ ≤ VDD1 30 Input capacitance Input current Input/Output SDA H-input voltage L-input voltage L-output voltage Input leakage current Input capacitance C IIN – 30 VIH VIL VQL ILeakage C 0.7 × VDD1 V VDD1 0 0.3 × V VDD1 0.4 – 10 10 10 V µA pF IQL = 3 mA, VDD1 = 5 V, CL = 400 pF 0 ≤ VIN ≤ VDD1 Semiconductor Group 7 04.96 SDA 4331X 4.3 AC/DC Characteristics (cont’d) Symbol Limit Values min. typ. max. Unit Test Condition Parameter Inputs SCL, A0 H-input voltage L-input voltage Input leakage current Input capacitance VIH VIL ILeakage C 0.7 × VDD1 V VDD1 0 – 10 0.3 × V VDD1 10 10 µA pF 0 ≤ VIN ≤ VDD1 Outputs SA1, SA2, SA3, SA4, AM/FM (open drain outputs) L-output voltage VQL VQL 0.4 0.1 V V IQL = 1 mA VDD1 = 5 V IQL = 0.1 mA Input IREF Input current Voltage at IREF Output PDFM PD current A PD current B PD current C PD current D Output PDAM PD current A PD current B PD current C PD current D IIN VIREF t.b.d. 100 1.2 t.b.d. µA V IIN = 100 µA IQ IQ IQ IQ ± 4.5 ±3 ± 1.5 ± 150 mA mA mA µA VPD = 4 V IQ IQ IQ IQ ± 450 ± 300 ± 150 ± 30 µA µA µA µA VPD = 4 V Semiconductor Group 8 04.96 SDA 4331X 4.3 AC/DC Characteristics (cont’d) Symbol Limit Values min. typ. max. Unit Test Condition Parameter Output PDFMA H-output voltage H-output current L-output current VQH IQH IQL 7.5 7.7 2 5 V mA µA 10 IQH = 2 mA VPD FM = VDD2 = 9 V VPD FM = VDD2 = 9 V VPD FM = GND VQ = 4 V Output PDAMA H-output voltage L-output current IQH IQL 1 0.1 2.5 mA mA VPD AM = 5 V VPD AM = GND VQ = 5 V Note: The listed characteristics are ensured over the operating range of the integrated circuit. Typical characteristics specify mean values expected over the production spread. If not otherwise specified, typical characteristics apply at TA = 25 °C and the given supply voltage. Table 1 Programming of Mode and Frequency Resolution AM/FM 0 0 0 1 1 1 R1 0 1 1 0 1 1 R0 1 0 1 1 0 1 Mode FM FM FM AM AM AM Frequency Resolution [MHz] 12.5 25 50 1 5 10 Semiconductor Group 9 04.96 SDA 4331X Table 2 Programming R-prescaler RP1 0 0 1 1 RP0 0 1 0 1 Divide Ratio 1:1 1:80 1:160 1:205 Quartz Frequency [MHz] Test mode only 4 8 10.25 Table 3 Programming Phase Detector PD1 0 0 1 1 PD0 0 1 0 1 Current Level D C B A PPD 0 1 Polarity Normal Invers Table 4 Programming Test Mode T1 0 1 T2 0 0 PD_MUX SA1 SA2 SA3 SA4 T3 Operation 0 1 Normal Test reset Controlled by I2C Bus Clk_50 kHz N_A_CLN Semiconductor Group 10 04.96 SDA 4331X Diagram 1: I2C Protocol Slave-receive (Write) START 1 1 0 0 1 0 0/1 0 ACK MSB N14 N13 N12 N11 N10 N9 N8 ACK A/N-counter N7 N6 N5 N4 N3 N2 N1 LSB ACK [STOP or START]: [STOP or START] Optional STOP or START condition, after power ON AM/FM the complete sequence has to be programmed. PD1 PD0 IF SA4 SA3 SA2 SA1 ACK [STOP or START] G1 G0 F0 R1 R0 RP1 RP0 0 ACK [STOP or START] PPD T0 (= 0) T1 (= 0) T2 (= 0) T3 (= 0) X X X ACK STOP or START Semiconductor Group 11 04.96 SDA 4331X Figure 3 Application Circuit for AM and FM Charge Pump Output Semiconductor Group 12 04.96 SDA 4331X 5 Package Outlines P-DSO-24-1 (Plastic Dual Small Outline Package) Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book “Package Information”. SMD = Surface Mounted Device Semiconductor Group 13 Dimensions in mm 04.96 GPS05144